Table of Contents
Advertisement
SERVICE AND ADJUSTMENTS
&
WARNING: To avoid
serious
injury,
before performing
any service or ad-
justments:
1. Be sure throttle is in STOP position.
2. Remove safety Ignition key.
3. Make sure the augers and all moving
parts have completely
stopped.
4. Disconnect
spark
plug wire from
spark plug and place wire where it
cannot come in contact with plug.
SNOW THROWER
TO ADJUST SNOWTHROWER
HEIGHT
See "TO ADJUST SKID PLATES" and "SCRAPER BAR"
in the Operation section of this manual.
CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
I
w..-oovo,°-r,--,n,
I
never operate your snow thrower with
the deflector removed or damaged.
•
Tochange directionand/or distance snow is discharged,
see "TO CONTROL SNOW DISCHARGE"
in the Op-
eration section of this manual.
SHEAR BOLTS (See Fig. 18)
AUGER SHEAR BOLTS
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other components. If one or both augers do not turn when
auger controllever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
1.
Disengage all controls and move throttle control to
STOP position.Wait for all moving parts to stop.
2.
Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
3.
Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shoulder/shear bolt. Install
1/4-20 lock nut and tighten securely.
I
CAUTION: Do not substitute. Use only original
I
equipment shear bolts as supplied with your
I
snow thrower.
4.
Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shear bolts and hex nuts. Should a foreign object
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other com-
ponents. If impellerdoes not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
1.
Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2.
Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
3.
Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 Iocknuts and tighten securely.
I
4.
I
CAUTION: Do not substitute. Use only original
|
equipment
capscrew/shear
bolts as supplied
I
with your snow thrower.
Connect spark plug wire to spark plug.
1L _ '20NUT_
1/H_'E_ASOC_IlBEo_L_
:HIAU4"RL20_XRLi
_
'MPELLEF_R
g
LOCKNUT_
_
AUGER HUB
"AUGER SHAFT
FIG. 18
TO REMOVE BELT COVER (See Fig. 19)
1.
Remove the two (2) screws securing belt cover to
frame,
2.
Remove belt cover.
SCREWS
16
FIG. 19
Advertisement
Table of Contents
