This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered,
brush-
covered or grass-covered
land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required
by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark
arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department,
Page 1
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 PRINTED IN U.S.A. FORM NO.
TABLEOFCONTENTS Content Page Important Safe Operation Practices ..............Assembling Your Chipper Shredder Vacuum ............ Know Your Chipper Shredder Vacuum .............. Operating Your Chipper Shredder Vacuum ............Maintaining Your Chipper Shredder Vacuum ............ Troubleshooting ....................Parts List ......................FINDINGMODELNUMBER This Operator's Manual is an important part of your new chipper shredder vacuum. It will help you assemble, prepare and maintain the unit for best performance.
SECTION 1: IMPORTANT SAFEOPERATION P RACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Page 4
g. Replace g asoline capandtighten securely. Never operate without either the inlet nozzle or h. Ifgasoline is spilled, w ipeitofftheengine optional hose attachment properly attached to the andequipment. Movemachine toanother machine. Never attempt to attach or change either area. W ait5 minutes b efore starting the attachment while the engine is running.
understand and follow the warnings and instructions in this manual and on the machine. ARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, NOTE: Not all safety labels shown may apply to your model chipper shredder vacuum. TO AVOID SERIOUS iNJURY...
Page 6
Attaching TheHandle • Unfold the upper handle until it aligns with the lower Bag Handle handle. • Secure the two handles by tightening the wing nuts (carriage bolts must be seated properly into the handle). See Figure 2. • Remove the hairpin clips from the handle brackets on the chipper shredder vacuum and remove the carriage bolts and wing nuts from the lower handle.
SECTION 3: KNOW YOUR CHIPPER SHREDDER V ACUUM Blower Chute (if so equipped) Bag Handle Nozzle Height Adjustment Lever Chipper Chute Nozzle Figure 5 Read this operator's manual and safety rules before small twigs across yard. See Figure 5. operating your chipper shredder vacuum. Compare the Nozzle HeightAdjustmentLever illustrations in Figure 5 with your unit to familiarize Used to adjust the nozzle ground clearance ranging...
Page 8
StartingEngine • Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine • Attach spark plug wire to spark plug. Make certain to release. the metal cap on the end of the spark plug is •...
IMPORTANT: The flail screen is located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in SECTION 5: MAINTAINING YOUR CHIPPER SHREDDER VACUUM. For best performance, it is also important to keep the chipper blade sharp. adjustments without first stopping engine and WARNING: Do not at any time make any...
Page 10
• Check engine oil level before each use as • Remove hex screw and flat washer on top of rear instructed in the separate engine manual packed housing mounting bracket and the lock nut that with your unit. Read and follow instructions secures flail screen.
Page 11
• Apply lubricant to the threads of impeller removal tool and then thread the tool into the crankshaft. Stop when the impeller assembly can move on the crankshaft. Housing • Remove the impeller assembly from the crankshaft. Unthread the impeller removal tool from the impeller assembly.
SECTION 6: TROUBLESHOOTING Problem Cause Remedy Engine fails to start Spark plug wire disconnected. Connect wire to spark plug. Fuel tank empty or stale fuel. Fill tank with clean, fresh gasoline. Throttle control lever (if so equipped) Move throttle lever to FAST position. not in correct starting position.
Page 16
MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with MTD does not extend any warranty for products sold or respect to new merchandise purchased and used in the exported outside of the United States, its possessions United States, its possessions and territories.