Page 2
Once your PHILIPS MAGNAVOX purchase is registered, you're eligible to receive all the privile, of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once.And take advantage of these important benefits.
Page 3
:Introduction3 Welcome to your VCR owner's manual• This manual has seven sections: Setting Up Your VCR; Description of Controls; Basic Operations; Recording; _ Playing; Stereo Features; and Information You May Need.The instructions explain all of theVCR's features, which are listed below.You cannot hurt yourVCR by trying the features! So read on - and relax.
4:Tableof C ontents Setting Up Your VCR Introduction ........: ..'....Table of Contents ...._. _..."., ....,..Before UsingYourVCR ....,......Hookups Without a Cable Box ..........
Replace the battery compartment lid. Using the Remote Control • Point the remote control at theVCR's remote sensor (see page 27) when using the remote control to operate the VCR. Point the remote control at the TV when using the remote control to operate the TV.
8 HookupsWith a CableBox/Digital Satellite System • eo6e. • oo_aQ eeo4o meeoo.oe oeoo .eOOOQOQe Oe.eO.O.eOO_.JOeOO • Q OOOaOO4 OOeOtOOQ.e eooeQoe• .eO• OOOOQ.OO • Q •eeoooee This connection allows you to view any channel. After you connect the Cable Box/Digital Satellite System,VCR, and TV as shown below, the features described...
Page 10
antennaor cableto ANT(enna) IN Jack Audno andV,deo IN JacksonTV VIDEO (yellow) andAUDIO (red andwhite) OUT Jacks Audio Cable • Audio andVideo cables are not supplied. Connect the antenna or cable to the ANT(enna) IN Jack on the back of theVCR. Connect a video cable to the yellowVIDEO Jack on...
Turning onYour VCRII Turn on the'l-V. Before turning on yourVCR, make sure there are batteries in the remote control and theVCR and "IV are connected correctly. • Follow the steps on this page only when you plug theVCR power cord into the wall oudet for the first time. •...
12 ChannelMemory • •1• ••••1 •• • • ••••ooeieee •ie•••••••• • • 1•••• cole iiee• eeee • e• • ee • • • eeeeeeeo• ioe• ••••eoeeee• • • • • • •••••••••1•1• Programming Channels Although yourVCR may automatically memorize the channels you receive when you turn it on for the first time, this function lets you reprogram channels.
Page 13
Channel Memory ( cont,d) 1 3 Adding/DeletingChannels Press the VCR button. Press the MENU button to bring up the main menu display. Press the Number 3 button to selectTUNER SET UP. Press the Number 4 button to selectADD/DELETE CH. END PUSH EXIT Use the Number buttons to enter the channel number.
14 Setting t heClock: ooeoeeeeoeoee • • o••• •o co• eoee • • •el • eo• eeeeeoeeeeoee ooeoeeooeeoee • eeoeeee•e • •ooee e•oeoeee•ee • ooa•o • • •e • • • There are two ways to set the clock.With manual clock setting, you tell the VCR the current time.With automatic clock setting, theVCR gets the current time from your local PBS station.
Page 15
Setting t heClock (cont,d) 15 Press two Number buttons for the hour(s) and two Number buttons for the minute(s).Then press I forAM or 2 for PM. For example, for 2:15 PM, press 02, I S, 2. • Enter a 0 before a single digit number. •...
Page 16
16 Settingthe C lock (cont'd) Automatic Clock Setting Press the VCR button, then press the MENU button bring up the main menu display. PROGRAM TUNER SET UP SET CLOCK END PUSH EXIT Press the Number 4 button to select SET CLOCK. 2 SET MANUAL CLOCK 3 DAYUGHT...
Page 17
Setting t heClock (cont'd) 1 7 Time Zone When using the AUTO CLOCK function, you can specify a time zone in which a local PBS channel is located.That way, theVCR will update the clock according to your time zone. Press theVCR button, then press the MENU button bring up the main menu display.
18 Dayh'ght-SavingTime Selection Daylight-Saving Time Selection You may program theVCR so its clock will automatically move forward one hour in April and turn back one hour in October. Dayiight-SavingTime is set to ON prior to shipment from the fac- tory. You may turn Daylight-SavingTime ON or OFF by following steps below.
Language Selection Follow the steps below to changethe languageof the on-screen displays. Press theVCR button. Press the MENU button to bring up the main menu display. PROGRAM VCR SET UP TUNER SET UP SET CLOCK SELECT PUSH NO. SHOWN END PUSH EXIT Press the Number 2 button to selectVCR...
• Although the remote control that comes with your VCR will work most Magnavox TVs,as well as many TVs sold under other brand names, it is Within 30 seconds after releasing the MUTE button, press and possible that the remote control will release the TV button.
Page 22
EJECT Button When playbackis stopped, press to eject the tape. PAUSEISTILL In Record mode, press to temporarily stop the recording (pause). Press a second time to resume normal recording. Details are on page 3 I. You can not pause a one touch recording that is set for a specific length of time.
Page 23
Remote C ontrol Buttons (cont'd) 2 3 REC(ord)IOTR Press once to start a recording. Details are on page 3 I. Or, press three to 18 times to start a one touch recording (an imme- diate recording, 30 minutes to eight hours long) of the channel you are watching.
24 Remote Control B uttons ( cont'd) Press to erase incorrect data when programmingVCR functions.Also, press to reset the real time counter. Details are on page 45. MEMORY Press to memorize a tape position at which the real time counter was set to 0:00:00.
VCR Display Panel 2 5 Cassette Compartment Insert a tape here. Information aboutVCR operations appears here. VORO,,p,ay ano, I BD _" PHILIPS Timer Light This light glows when you turn off the VCR when a timer recording has been set. It also glows when a one touch recording has been set.
26 Front Panel PLAY Button Press to play a tape.Also, press to release Slow, Search or Still mode and to return to normal play- back. Details are on pages 46-47. POWER Button STOPIEJECT Button Press to turn theVCR _ower on and off. Press once to stop the tape.When playback is stopped, press to eject the tape.
Front P anel ( cont'd)27 RFWD (Fast Forward) Button When in Stop mode, press to fast forward the tape at high speed. When in Play mode, press to fast forward while the picture stays on- screen. Details are on page 46. - REW(ind) Button Remote...
28 Rear Panel ANT(enna) IN Jack Connect your antennaor cab._ ix-IO. here. Details are on pages AUDIO IN Jacks Connect the cables coming from the AUDIO OUT Jacks of a cam- corder, anotherVCR, or an audio source here. Details are on page 42. AUDIO OUT Jacks Connect the cables going to the...
On.Screen S tatus Displays 29 ooeeeoolooeoeoleoDleoeo •eeeoeeeoQoeeeoeelmQeeeoooetoooeeeee• eeQeeeeeeoeoooeeeeoeoees e• eeeo• • eeoo• eeoeeoo Function Receiving and A status display, which includes the current time, channel, and other information (see illustration), will appear when you press the STA- Button Recording Mode TUS/EXIT button or certain function buttons.The contents of the sta-...
30 Playing looooool. • ooo •• •• oooo Q oooouQ • tleoeooloQoeooeooooeooooloeolooBeeo • oololoooooooooeeo • • ••••••Qoos •e •••••eeooo• _ • Insert a tape in theVCR. Read and follow the steps below to play a tape. Turn on the'IV. Turn theTV on and set it to channel 3 or 4, whichever the CH3/CH4...
Recording 31 eeeee •eee • • •••0••••• • • • ••••••eeeeeoeeoeoeeeeeeeee eoooeeoeeeee•eeee• • e•eooe•ee••• eeeo ••eeee• 0• • eeee •• Insert a tape in theVCR. Read and follow the steps below to record a television program. Turn on the T_. Turn the TV on and set it to channel 3 or 4, whichever the CH3/CH4...
Page 32
32 Recording OneChannel/Watching Another Start a recording (see page 31). Press the VCR button. Press the VCR/TV button to put the VCR in TV position.The VCR light will disappear from the VCR's display panel. Press theTV button, then press the CHANNEL (Up/Down) or Number buttons...
OneTouch R ecording 33 The one touch recording (OTR) functionallowsyou to program an immediatetimed recording 30 minutes to eight hours long without settingthe timer. Beforeyou begin,make sure: • Channelsare programmed. • The desired recording speed (SP,LRor SLP)hasbeen selected with the (Tape)SPEEDbutton. •...
34 Timer R ecording Follow the steps below to programyourVCR to record TV pro- grams while you're away from home.You can program up to eight timer recordings. For each one, the VCR will turn itselfon, record, and turn itself off automatically. Before you begin make sure: •...
Page 35
Timer R ecording (cont'd) 3 5 Use the Number buttons (I - 8) to select a slot in which to store the timer recording. There are eight timer recording slots. Open slots will flash on-screen. NOTE:If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLYSET PROGRAM will appear on- screen for a few seconds.
Page 36
36 Timer R ecording (cont'd) Press the Number I button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed. (For details, see the chart below.)You cannot use the (Tape) SPEED button at this time.
Timer R ecording (cont'd) 3 7 Checking or Cancelling Timer Recordings With the VCR on and inVCR position (the VCR lightwill appear on the display panel), press theVCR button, then press the MENU button. Press the Number I button to select PROGRAM. Press the Number 4 button to select PROGRAM...
38 Setting U ptheVCR Plus+ Programming System First, fill in the boxes on this page.It will only take a few minutes, and you must do it if you want theVCR Plus+ programming system to work properly. Sincethe channelnumbers of the stations you receive may not be the same as the station numbers, and since channel numbers differ from area to area,you must program the VCR with your local channel infor- mation.To fill in the boxes, you will need I) a cable channelline-up list, if applicable (you can request one from your cable company), and 2) a chart that listsVCR Plus+ channel numbers, which you can find in your...
Setting UptheVCRPlus+ Programming System (cant'd)39 Examine the listson page 38. Now, compare the channelnumbers you have written in theVCR PLUS+ CH. and CABLEJTV CH. columns.You'll n otice that some stations haveVCR Plus+ and CableFl'V channel numbers that are the same,and other stations have channel numbers that do not match.Where the channel numbers DO NOT match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps.
Page 40
40 Timer R ecording With theVCR Plus+ Programming System eeeeeeee*ee .eee eeoeee_oe.oeoooooe eeeoe eieeee.e *eeoc .eeQeeeeeeeeeeee.e.eeoe o*ee • e••eee•.•e•e.e.•ee•.e Follow the steps below to program a timer recording using the PlusCode programming numbers in your'IV guide. Before you begin, make sure: EJ_'TA •...
Timer R ecording With theVCR Plus+ Programming System (cont'd) 4 1 Press the Number I button to record in SP speed, the Number 2 button to record in LP speed, or the Number button to record in SLP speed. Your selection will appear to the right of REC SPEED on-screen, although SP= I LP=2 SLP=3 will condnue to flash.
42 Rerecording (Tape Duplication) • i • oooo o• I• • • •••s • vynvR R Reco nVR D • RFc-- (supplied)from VCR's OUT Jack TV's ANTENNA IN Jack I.Audio cablesfrom AUDIO OUT ofVCR I to AUDIO IN ofVCR 2 Jacks Jacks 2.Video cablefrornVIDEO OUT...
Repeat Playback 43 Repeat Playback Follow the steps below to program the VCR to play a tape over and over. Press theVCR button. Press the MENU button to bring up the main menu display. PROGRAM VCP. SET TUNER SET UP SET CLOCK SELECT PUSH...
44 Time Search Press theVCR button. Press theTIME SEARCH button to bring up the time search display.There must be a tape in theVCR. IME SEARCH 0._0 NTER SEARCH TIME Within I 0 seconds, use the Humber buttons to enter the desired length of time you want to skip forward or back- ward.
RealTime C ounterMemory 45 Real Time Counter Memory Followthe stepsbelow to reset the real time counter to zero at a tape locationyou want to refer to later. Play, fast forward, or rewind a tape to the location that you would like to refer to later.
46 Special Effects P layback Forward and Reverse Searching (SP/LP/SLP) When in Play mode, press and release the F.FWD button the REW(ind) button. A fast forward or reverse picture search will begin. To return to playback, press the PLAY button. Super High Speed Searching...
Special Effects P layback (conted) 47 "_i,ew, n_ a'_iow'i4o;:ion"_ic;_ure" .........._;i" ..""_'" ..When in Playmode, press the SLOW button. The tape will play in slow motion. NOTE:You cancontrol the speed of slow motion playbackby pressing the VAR(iable). SLOW buttons. To release Slow mode and return to normal playback, p ress the PLAY button or press the SLOW button again.
48 Automatic• Operation Features e_oo • eeeoo • • •oQ ••.oeooeo_oo_•o • •0• • oooQ •oo •••e .•• e_oeo •_o eoeoeoiom •••o_•• e_Qoeoooeoou. •*•••• • ••• • e• • • • •e • ooooeo The following playback features will always operate: __ _ '* _ _ _ : _'?
Page 49
Automatk Operation l Features (€ont'd) 4 9 To adjust the tracking manually, press the CHANNEL (Up/Down) buttons on theVCR during tape playback. NOTES: • This _unction is controlled on/y by the CHANNEL (UplDown) buttons on the VC/_ The CHANNEL (UplDown) buttons on the remote con- trol will not adjust tracking.
Page 50
50MTSBroadcast StereoSystem • O*04 eee•oo 40COLD •o_ De• oDe••oDe • • eeeoee •co • • •••• • •e•e• *•• ••e•e eieoooeoeoe ee•ee• • ••oee•e•••,•eoe•e••• • • oeJ• • ¥ourVCR can playrecordings broadcastin Hi-Fi (high fidelity) stereo,which producesa •crisp, clear soundL. from two sources.YourVCR also can playtapes recorded in a secondaudio (usually, that meansyour pr_ gram is recorded in a secondlanguage).Of course,yourVCR will playtapes recorded in monaural (singl.
MTSBroadcast StereoSystem(co_t_'d) Press the VCR button, then press the MENU button. slow Press the Number 3 button to selectTUNER SET UP. 3 AUTO PROGRAHHING 4 ADD/DELETE CH 5 CH MEMORY REVIEW 6 TV STEREO / ITv_fTO2 SELECTcABLE TvPUSH NO. SHOWNoN 1 7 2ND AUOIO TO END PUSH EXIT Press the Number 6 button to selectTV STEREO or the...
Hi-FiStereo Sound System (con t'd)53 eoee • 4Qee • oeeeeeee • eeeeeeeeeoe • • • eeoeoeoo4oeoe4 • ••eeeeee• oeoeo eeeeee eeeo ••eeeQ ee• eeooo ••e oooo •••• • Press the MENU button to bring up the main menu display. Press the Number 3 button to selectTUNER SET UP. 2 CABLEIW 3 AUTO Pfl.OGRAMMING...
54 Helpful Hints ..• oooeee •_ ooeeo 4_o_•oo ooeQ oo• e•4 •oe o_•o oooo •_o o_ooo _•o • oeoo .ooo•4 oooo • e• ••4••_ooe eeoeooeoeo coo••co•••e• If you are having problems with yourVCl_ check the following list of problems and possible solutions before requesting service.You may be able to solve the problem yourself.
Helpful H ints (cont'd) 55 • so•o•••• • Qoooto_e •oo• •QIOOetOOleOOOOOIOItQOOIOOOQOeOOQOQ ••• I• QO• • OOOOO• • O_O• O•• O• Be OOI ..•OOOO• e"• 'l'O'IOOe• OQOOIO TV programs cannot be watched normally. • Put theVCR in "IV position. (Press theVCR/'I'V button so that theVCR light disappears from the display panel.
58Limited W arranty VIDEO CASSETTE RECORDER 90 Days Free Labor/One Year Parts Exchange. This product must be carried in for repair. IS COVERED? may be a delayif the appropriatespare parts and technical manual(s) are not readily available). You must have proof of purchase to receive warranty service.A sales receipt or other document showing MAKE SURE YOU KEEP...
Index 59 eeooeeeeeeeo eeoc • • ee•eeooe eeeeoeoee oeoeooeee.eoooe• eeeo eee,eeee• oeeeeeee•o•o• • ••••leeoeeeee ,e•e •,oeeeee ac power cord ......i..28 long play........36, 56 speed button ........22 accessories........60 Ip ..........36, 56 standard play......36, 56 ant(enna) in jack ....6- IO,28 status display........
Check to be sure the items on this page are packed with your VCR. These accessories are provided to help you use or set up your VCR. "7000 300[3 -1000 [3O0 Remote Control 4835 218 37204 Two"AA" Batteries 4835 138 17012 RF Coaxial Cable, 75 ohm 4835 323 2701 I...