HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927...
TABLE OF CONTENTS Here's How To Get Help ........3 EC-10GH ROBIN ENGINE Table Of Contents ..........4 Crankcase and Cylinder.........28-29 Parts Ordering Procedures ........5 Crankshaft and Piston........30-31 Rules For safe Operation ........6-7 Governor ............32-33 Operation and Safety Decals ........ 8 Blower Housing &...
PARTS ORDERING PROCEDURES Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • UPS Ground • UPS Second Day or Third Day* •...
I NEVER use accessories or attachments, which are not I NEVER operate the rammer in an explosive atmosphere or recommended by Multiquip for this equipment. Damage to near combustible materials. An explosion or fire could result the equipment and/or injury to user may result.
I NEVER use accessories or attachments, which are not I Always know the location of the nearest fire extinguisher recommended by Multiquip for this equipment. Damage to and first aid kit . Know the location of the nearest telephone. the equipment and/or injury to user may result.
To maintain optimum performance, proper operation and service are essential. Construction of Tamping Rammer The Mikasa MT-70H is equipped with an air cooled, two cycle gasoline engine. Transmission of the power takes place by increasing the engine speed to engage the centrifugal clutch.
16. Spark Plug – Provides spark to the ignition system, excess fuel is present in the carburetor, or crankcase. L1. A Returned Material Authorization must be approved by Multiquip prior to shipment. A copy of the Authorization must replace with engine manufactures recommended type accompany the shipment to the designated Warehouse.
MT-70H — OPERATION Inspection This section is intended to assist the operator with the initial start-up of the MT-70H Tamping Rammer. It extremely important 1. Check all nuts, bolts fasteners for tightness. Retighten as neces- that this section be read carefully before attempting to operate sary.
MT-70H — OPERATION 2. Close the choke lever Figure 3 and move the throttle lever to the "Full Open" position. Turning the choke lever 90 degrees clockwise closes the choke . In cold weather, start the unit with choke fully closed. In warm weather or when the engine is warm, the unit can be started with choke halfway or completely open.
MT-70H — MAINTENANCE I The air cleaner on the engine side will hardly be Maintenance contaminated, if it is, however after cleaning the element Perform the scheduled maintenance procedures as indicated: with kerosene, dip it in mixed oil consisting of 3 parts of DAILY gasoline and 1 part of engine oil.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
MT-70H — GUIDE CYLINDER AND FOOT GUIDE CYLINDER AND FOOT PAGE 22 — MT-70H — PARTS & OPERATION MANUAL — REV. #5 (03/01/01)
Page 23
MT-70H — GUIDE CYLINDER AND FOOT GUIDE CYLINDER AND FOOT PART NO PART NAME REMARKS 352423290 PISTON PIN 080100150 STOP RING ..........2 ..REPLACES 301010350 352210510 PISTON ROD 352423300 PISTON END 020118150 NUT M18 P1.5 352321900 MAIN SPRING ......... 2 ..REPLACES 352321620 352209360 SPRING CYLINDER 352208510...
MT-70H— TANK AND HANDLE 1 TANK AND HANDLE 1 PART NO PART NAME REMARKS 353910010 FUEL TANK INCULDES ITEMS W/ 352111820 HANDLE 351319900 SHOCK ABSORBER 014210020 SOCKET HEAD BOLT 10X20 REPLACES 001521020 033121009 TOOTHED LOCK WASHER M10 012210020 BOLT 10X20 REPLACES 002211020 351110650 FUEL TANK 3L (P)
MT-70H — TANK AND HANDLE 2 TANK AND HANDLE 2 PART NO PART NAME REMARKS 352108250 HANDLE 352321591 SUB HANDLE ........1 ... REPLACES 352321590 35131990 SHOCK ABSORBER 0105091025 BOLT 10X25 T ........4 ...REPLACES 001221025 030210250 WASHER SW M10 031110160 WASHER PW M10 020310080...
EC-10G ENGINE (ROBIN) — CRANKCASE AND CYLINDER CRANKCASE AND CYLINDER PAGE 28 — MT-70H — PARTS & OPERATION MANUAL — REV. #5 (03/01/01)
Page 29
EC-10G ENGINE (ROBIN) — CRANKCASE AND CYLINDER CRANKCASE AND CYLINDER PART NO PART NAME REMARKS 1061030501 CRANK CASE CP ........1 ..INCULDES ITEMS W/ 0310060010 DOWEL PIN 0440200010 OIL SEAL 044008010 OIL SEAL 7.4X14X4 0600200020 BALL BEARING (6204C3) 0105070010 STUD 0200070030 WASHER EC10 0100070010...
EC-10G ENGINE (ROBIN) — CARBURETOR & AIR CLEANER CARBURETOR & AIR CLEANER PART NO PART NAME REMARKS 1066252100 CARBURETOR ASSY......1 ..INCLUDES ITEMS W/ 2366254008 PACKING 1616235008 FLOAT BODY 2366250508 FLOAT 2366245008 PACKING 1616235108 BOLT 2266240208 MAIN JET # 72.5 2366244508 SPRING 2146251508...
Items purchased in kits. item with respect to which damages are claimed, be approved by Multiquip prior to shipment. and in no event shall Multiquip be liable for loss The sender will be notified of any material To obtain a Return Material Authorization, of profit or good will or for any other special, received that is not acceptable.