Foreword; Copyright; Precautions; Installation - Marantz SR9200 User Manual

FOREWORD

This section must be read before any connection is made to the mains
supply.
WARNINGS
Do not expose the equipment to rain or moisture.
Do not remove the cover from the equipment.
Do not push anything inside the equipment through the
ventilation holes.
Do not handle the mains lead with wet hands.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to comply with the
household power and safety requirements that exist in your area.
SR9200 can be powered by 230 V AC only.
IMPORTANT: (FOR UK VERSION ONLY)
This apparatus is fitted with an approved moulded 13 Amp plug.
To change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362 13A, A.S.T.A. or BSI
approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut
off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 13A. If a
plug without a fuse is used, the fuse at the distribution board should
not be greater than 5A.
Note:
• The severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
HOW TO CONNECT A PLUG
The wires in this mains lead are coloured in accordance with following
code: – green - and - yellow : earth
– blue : neutral
– brown : live
As the coloured of the wires in the mains lead of this apparatus may
not correspond with the coloured makings identifying the terminals in
your plug, proceed as follows:
– the wire which is coloured green and yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
earth symbol , or coloured green or green and yellow.
– the wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
– the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of lead – not simply over the two wires.

COPYRIGHT

Recording and playback of any material may require consent. For
further information refer to the following:
- Copyright Act 1956
- Dramatic and Musical Performers Act 1958
- Performers Protection Acts 1963 and 1972
- any subsequent statutory enactments and orders
ABOUT THIS USER GUIDE
Refer to the figures on page 2 of this user guide. The numbers on the
figurescorrespond to those in the text. All references to the
connections and controls that are printed in BOLD type are as they
appear on the unit.
2

PRECAUTIONS

The following precautions should be taken when operating the
equipment.
GENERAL PRECAUTIONS
When siting the equipment ensure that:
- the ventilation holes are not covered;
- air is allowed to circulate freely around the equipment
- it is on a vibration free-surface;
- it will not be exposed to interference from an external source;
- it will not be exposed to excessive heat, cold, moisture or dust;
- it will not be exposed to direct sunlight;
- it will not be exposed to electrostatic discharges
Never place heavy objects on the equipment.
If a foreign body or water does enter the equipment, contact your
nearest dealer or service centre.
Do not pull out the plug by pulling on the mains lead, hold the plug.
It is advisable when leaving the house, or during a thunderstorm, to
disconnect the equipment from the mains supply.
PRECAUTIONS IN CONNECTION
• Be sure to unplug the power cable from the AC outlet or turn off the
POWER/STANDBY switch before proceeding with any connection.
• Connect one cable at a time observing the "input" and "output".
This will avoid any cross connection between channels and signal
inputs and outputs.
• Insert the plugs securely. Incomplete connection may result in
noise.
• Prior to connecting other audio and video equipment to the SR9200,
please read their owner's manuals.

INSTALLATION

If this unit or another electronic device incorporating a microcomputer
is used at the same time with the tuner or television, picture
disturbance or noise may occur. In such a case, install the unit
according to the following guide points.
• Separate the unit as far as possible from the tuner or television.
• Place the antenna wire for the tuner or TV apart from the power
cable and audio and video connection cables of this unit.
• Since the phenomenon is likely to occur when using an indoor
antenna and/or 300-ohm feeder wire, we recommend using an
outdoor antenna and 75-ohm coaxial cable.