Summary of Contents for Salus PL07
- Page 1 Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:02 Pump and Boiler Logic Module Model No PL07 Instruction Manual...
- Page 2 Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 PL07 INSTRUCTION MANUAL...
-
Page 3: Product Compliance
Always isolate the AC Mains supply before inserting or removing the unit from the KL06 wiring centre, or carrying out any work on the PL07 logic module. Please leave these instructions with the end user where they should be kept in a safe place for future reference. - Page 4 Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 INTRODUCTION The PL07 from Salus Controls is a modular pump and boiler logic control module, designed specifically for heating applications. FEATURES • Modular installation • Cage clamp wiring terminals (no terminal screws) • Separate circulating pump and boiler control relays •...
-
Page 5: Installation
/ heating system supplier for advice on how to continue. The PL07 logic module is not a standalone unit, and is intended to be mounted on a KL06 wiring centre. The wiring centre should be installed first, followed by the PL07 logic module. - Page 6 Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 There are few electrical connections required to the PL07, and these connections should be made to the cage clamp terminals on the front of the module (after first securing the cable in the KL06 wiring centre):...
-
Page 7: Cable Connections
Please take the following steps to make the wiring connections to the PL07: 1. Prepare the cable ends: • Strip outer sheath to a distance of 110mm •... - Page 8 5. Fit the protective cover: Secure the cover by turning the locking screws a quarter turn. ELECTRICAL SAFETY - The PL07 logic module should not be operated without the protective cover in place. PL07 INSTRUCTION MANUAL...
-
Page 9: User Interface And Controls
10:03 USER INTERFACE AND CONTROLS The status and operation of the PL07 is clearly shown by the use of two green Light Emitting Diodes (LEDs) on the module front panel: When initially powering up the PL07, both LEDs will turn on for about one second before turning off. -
Page 10: Jumper Setting Summary
Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 JUMPER SETTING SUMMARY Jumper Function Default Setting J1 – Boiler and Pump Jumper in ON position protection ON – OFF OFF – Disables boiler and pump protection (immediately turns pump and boiler relays on when a thermostat calls for heat). -
Page 11: Operation
OPERATION Boiler Control The PL07 will turn the boiler on when it receives a call for heat from any of the installed thermostats via the KL06 wiring centre. Depending on the jumper settings the boiler will be turned on immediately, or after a delay of three minutes. - Page 12 10/9/10 10:03 The boiler and pump will be turned on by the PL07 (immediately, or after a delay of three minutes) if there is a call for heat from any of the installed thermostats. Once all the thermostats are no longer calling for heat, the boiler will be turned off immediately and the pump will be operated in accordance with the relevant jumper settings (i.e.
-
Page 13: Maintenance
• Heating system time switch or programmer is switched on. WARRANTY Salus Controls warrants that this product will be free from any defect in materials or workmanship, and shall perform in accordance with its specification, for a period of two years from the date of installation. Salus Controls sole liability for breach of this warranty will be (at its option) to repair or replace the defective product. -
Page 14: Product Specification
Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 PRODUCT SPECIFICATION Model: PL07 Type: Controlled logic module for pump and boiler control in heating applications. Switching 1. Circulating Pump Relay: Switching Voltage: 230V AC, 50Hz Switching Current: 5A resistive, 2A inductive Contact Type: Normally Open 2. - Page 15 Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 PL07 INSTRUCTION MANUAL...
- Page 16 Salus PL07 Manual Ver007.qxd:Layout 1 10/9/10 10:03 salus-tech. Email: sales@salus-tech.com Tel: 01226 323961 Sales Email: tech@salus-tech.com Tel: 01226 323961 Technical Salus Controls plc, Salus House, Dodworth Business Park South, Whinby Road, Dodworth, Barnsley S75 3SP...