Husqvarna CTH 224T Illustrated Parts List page 15

TRACTOR - MODEL NO. CTH 224T (96051007800), PRODUCT NO. 960 51 00-78
MOWER DECK 44 44
KEY PART
NO. NO. DESCRIPTION
1 580 97 33-01 Deck Weldment
2 532 42 30-62 Palnut 1/4
3 873 90 05-00 Nut Lock Hex Flange 5/16 - 18
5 817 00 05-10 Bolt 5/16-18
11 532 13 77-29 Screw Thd Roll 1/4 - 20 X 5/8
13 872 11 06-12 Bolt Carr Sh 3/8 - 16 X 1-1/2 Gr. 5
14 532 15 60-85 Keeper Belt Idler
16 873 90 06-00 Nut Lock FlG 3/8 - 16 unc
17 532 40 02-34 Nut Flange Lock Top
18 532 18 76-90 Washer Spacer Mandrel
19 532 11 04-85 Bearing Ball Mandrel
20 532 17 39-84 Screw Thread Roll
23 817 49 06-28 Screw Thdrol 3/8 - 16 X 1-3/4
27 532 44 58-86 V-Belt Drive
32 532 44 62-05 Spring Drive
33 580 79 61-01 Mandrel Asm. Tall
34 580 85 47-01 Shaft Asm Mndrl N/Greaseable38
35 581 51 79-01 Blade Mower LH
36 532 19 30-03 Bolt/Washer Asm 7/16 - 20 unf
42 817 00 05-12 Screw 5/16-18 x 3/4
43 532 44 32-39 Pulley Mandrel
45 581 65 08-01 Mandrel Asm. Short
72 581 45 41-01 Chute Upper
75 532 13 14-94 Pulley Idler Flat
76 532 41 55-98 Washout Port
84 532 44 32-35 Keeper Belt LH Mandrel
85 581 51 80-01 Blade Mower RH
86 532 18 17-13 Bolt 3/8-24 x 1.50 Gr. 8
87 810 03 06-00 Washer Lock Hvy. 3/8
88 532 14 02-96 Washer Hard
91 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.
94 532 19 72-50 Bracket Clutch Cable
95 817 00 06-12 Screw 3/8-16 x 3/4
96 532 40 02-71 Spacer
97 532 18 20-61 Shield Idler Mower
98 532 19 51-61 Stud Fastener
99 532 19 51-86 Arm Suspension Mower Rear
100 532 19 65-39 Bolt Shoulder
101 873 68 09-00 Nut Crownlock 9/16 - 18 unc
102 532 40 25-11 Spacer Bearing Swing Plate
104 581 71 40-01 Mandrel Cover RH
105 532 44 47-55 Mandrel Cover LH
110 532 41 53-56 Gear Output
111 532 43 69-79 Gasket Gearcase
112 532 44 38-52 Shaft Gearcase Adapter
113 532 43 85-33 Plug Oil
KEY PART
NO. NO.
114 532 43 85-34
115 818 03 10-16
116 872 11 04-14
117 873 90 04-00
118 532 44 32-32
119 532 43 81-66
120 532 44 32-36
121 532 43 69-85
124 581 65 07-01
125 532 44 04-20
127 532 19 34-06
128 532 17 48-73
129 532 44 32-37
130 819 13 13-12
131 532 19 42-08
143 532 43 81-97
144 532 43 58-61
145 532 43 79-88
146 532 44 58-96
154 532 19 98-55
159 581 48 72-02
160 581 48 71-02
161 581 48 73-02
162 581 48 74-02
163 872 11 04-06
250 819 11 12-12
- - 580 85 60-01
- - 581 65 05-01
- - 581 92 84-02
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
15
DESCRIPTION
Valve Relief
Screw Torx #10-24 x 1
Bolt 1/4-20 x 1.75 Gr. 5
Nut Hex Flange 1/4-20 unc
Arm Clutching
Gearcase Subasm
Keeper Belt RH
Washer
Non Greasable Mandrel Shaft
Bracket Idler Chassis
Bolt Shoulder 3/8-16 x 3-5/8 Gr. 5
Wheel Gauge
Rod Anti-Sway
Washer 13/32 x 13/16 x 12 Ga.
Pin Cotter 5/16 Bow Tie Lock
Door Mulch
Pin Hinge
E-Ring 5/16"
Spring
Screw Thd Roll 1/4-20 x 1/2
Plate 107 CRD LH Side
Plate 107 CRD LH Front
Plate 107 CRD RH Front
Plate 107 CRD RH Side
Bolt
Washer 11/32 x 3/4 x 12 Ga.
Mandrel Assembly Tall (Includes
Housing (key # 33), Shaft As-
sembly (key # 34), And Bearing
Only (key # 19) - Pulley/Nut/
Washer And Blade Bolt/Washers
Not Included.)
Mandrel Assembly Short (In-
cludes Housing (key # 45), Shaft
Assembly (key # 124), And Bear-
ing Only (key # 19) - Pulley/Nut/
Washer And Blade Bolt/Washers
Not Included.)
Replacement Mower Complete