Starting And Stopping; Oxygenated Fuels; Operating The Trimmer - Homelite UT21006 Operator's Manual

FUELINg AND REFUELINg THE TRIMMER
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
premixing gasoline and 2-cycle oil. The mixture should be
at a 50:1 ratio.
NOTE: We recommend you use ONLY Homelite (exact mix)
or G oil in your product.
TO MIX THE FUEL:
 Use a clean container that is approved for use with
gasoline.
 Mix the 2-cycle engine oil with unleaded gasoline in the
container, according to the instructions on the oil
package.
This engine is certified to operate on unleaded gasoline
intended for automotive use with an octane rating of 87
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle
outboard oil.
NOTE: Most fuel mixture will stay fresh up to 30 days. DO
NOT mix quantities larger than usable in a 30 day period.
PREMIUM EXACT MIX (50:1)
gASOLINE
1 gallon (US)
1 liter

OXYgENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR
WARRANTY.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated previously are
not covered under warranty.
Ethanol. Gasoline containing up to 10% ethanol by vol-
ume (commonly referred to as E10) or 15% ethanol by
volume (commonly referred to as E15) are acceptable.
Do not use E85 fuel.
FILLINg TANK
 Clean surface around fuel cap to prevent contamination.
 Set trimmer on its side so that the spout points up.
 Loosen fuel cap slowly. Rest the cap on a clean surface.
 Carefully pour fuel into the tank. Avoid spillage.
 Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
OPERATION
Always shut off engine before fueling. Never add fuel to a
machine with a running or hot engine. Move at least 30 ft.
from refueling site before starting engine. Do not smoke
and stay away from open flames and sparks. Failure to
safely handle fuel could result in serious personal injury.

STARTINg AND STOPPINg

See Figures 7 - 8.
Trimmer should be on a flat, bare surface for starting. The
starting method differs depending on whether the engine is
cold or warm.
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine starts
and runs.
 Lay the trimmer on a flat, bare surface.
 PRIME - Press the primer bulb 7 times.
 SET the start lever to the START position.
 PULL the rope until the engine starts.
LUbRICANT
 Squeeze the trigger to run.
2.6 oz.
NOTE: Squeezing and releasing the throttle trigger releases
20 cc (20 ml)
the start lever to the RUN position.
To restart a warm engine:
SQUEEZE the throttle trigger.
PULL the rope until the engine starts.
NOTE: If the engine starts and stops before the throttle trigger
engages, squeeze the throttle trigger and pull the rope until
the engine starts and runs. Squeezing and releasing the
throttle trigger releases the start lever to the RUN position.
To stop the engine:
Press and hold the quick shutoff switch in the stop "
position until the engine stops.
IF ASSISTANCE IS REQUIRED STARTINg
THIS PRODUCT:
Do not return this product to the retail store where it was
purchased. Please call our Customer Service Department
for any issues you may have.
For Help Call: 1-800-242-4672

OPERATINg THE TRIMMER

See Figure 9.
Always position the unit on the operator's right side. The
use of the unit on the operator's left side will expose the
operator to hot surfaces and can result in possible burn
injury.
Page 7 — English
WARNINg:
WARNINg:
"