Table of Contents
Advertisement
•
Watch forholes, r uts,bumps, r ocks, o rother
hidden objects. U neven terrain couldoverturn the
machine. Tallgrasscanhideobstacles.
•
Avoid turnswhen driving ona slope.Ifa turnmust
bemade, t urndown theslope. T urning upa slope
greatly increases t hechance ofa rollover.
•
Avoid stopping when driving upa slope.Ifit is
necessary t ostopwhiledriving upa slope, s tartup
smoothly a ndcarefully toreduce thepossibility o f
flipping thetractor o verbackward.
SettingTheCruiseControl
NOTE:
The cruise control feature should only be
utilized while traveling in the forward direction.
•
Place the shift lever in the FORWARD position,
then slowly depress the drive pedal until the desired
speed is achieved.
•
Lightly depress the cruise control button.
•
While continuing to hold the cruise button in, lift
your foot from the drive pedal (you should feel the
cruise latch engage).
•
Once engaged, the cruise control button and the
drive pedal will lock in the "down" position, and the
tractor will maintain the same forward speed.
NOTE:
Cruise control can not be engaged at the
tractor's fastest ground speed. If the operator should
attempt
to
do
so,
the
tractor
will
automatically
decelerate to the fastest optimal mowing ground speed.
Disengage the cruise control using one of the following
methods:
•
Depress the brake pedal to disengage the cruise
control and stop the tractor.
•
Lightly depress the drive pedal.
To change to the reverse direction when operating with
cruise control, depress the brake pedal to disengage
the cruise control and bring the tractor to a complete
stop. Then place the shift lever in the REVERSE
position and depress the drive pedal.
Using the DeckLiftLever
To raise the cutting deck, move the deck lift lever to the
left, then place it in the notch best suited for your
application. Refer to Setting TheCatting Heightearlier in
this section.
Engaging the PTO
Engaging the PTO transfers power to the cutting deck
or other (separately available) attachments. To engage
the PTO, proceed as follows:
•
Move the throttle control lever to the FAST (rabbit)
position.
•
Pull the PTO knob outward into the engaged (ON)
position. See Figure 8.
Front View
Pull Out
Push In
t
Figure 8
•
Keep the throttle lever in the FAST (rabbit) position
for the most efficient use of the cutting deck or other
(separately available) attachments
IMPORTANT: The electric PTO clutch will automatically
shut off if the PTO is engaged with the shift lever in
position for reverse travel. Refer to Safety Interlock
Switches on page 12.
Mowing
WARNING:
To help avoid blade contact or
a thrown
object
injury, keep
bystanders,
helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop
machine if anyone enters the area.
This tractor is equipped with one of MTD's high quality
cutting decks. The following information will be helpful
when using the cutting deck with your tractor.
WARNING:
Plan your mowing pattern to
avoid discharge
of materials toward roads,
sidewalks,
bystanders
and the like. Also,
avoid discharging
material against a walt or
obstruction
which
may
cause
discharged
material to ricochet back toward the operator.
•
Do not mow at high ground speed, especially if a
mulch kit or grass collector is installed.
•
For best results it is recommended that the first two
laps be cut with the discharge thrown towards the
center. After the first two laps, reverse the direction
to throw the discharge to the outside for the
balance of cutting. This will give a better
appearance to the lawn.
•
Do not cut the grass too short. Short grass invites
weed growth and yellows quickly in dry weather.
•
Mowing should always be done with the engine at
full throttle.
•
Under heavier conditions it may be necessary to go
back over the cut area a second time to get a clean
cut.
•
Do NOT attempt to mow heavy brush and weeds
and extremely tall grass. Your tractor is designed to
mow lawns, NOT clear brush.
14
Advertisement
Table of Contents
