Table of Contents
Advertisement
Watching TV
Perform the following
steps before you press POWER
on the remote control unit.
1
Insert the batteries
into the remote control unit.
(See page 8.)
2
Connect
the antenna
cable to the TV. (See page
12.)
3
Plug in the AC cord to the AC outlet. (See page 7.)
Press POWER
on the TV, or POWER
on the remote
control.
TV status
indicator
(POWER)
ON
Lighting (Green)
OFF/Standby
Lighting (Red)
Press POWER
on the TV, or POWER
on the remote
control.
• The TV enters standby mode and the image on the screen
disappears.
• The POWER indicator on the TV changes to Red.
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when POWER
is turned off.
You can change channels
in several ways.
Method 1
Using CH ^/v
on the remote control unit or on the
TV.
• POWER indicator (Green): The TV is on. ("Please wait"
will appear for a few seconds on the screen.)
The Auto Setup menu appears
the first time you
turn on the TV, and assists you to select the menu
language,
specify the Air/Cable
setting,
and program
your channels
automatically.
IMPORTANT:
Make sure that the antenna
or cable TV
system
connection
is made!
1
The turn on the TV, press POWER (POWER indicator on
the front of the unit changes green. It may take approx.
10 seconds for a picture to appear on screen.).
2
The "Auto Setup" function begins. Press ,/_ to select
your desired language.
3
Press A/T to select "Signal Type", then press ,/_
to
select "Cable" or "Air".
Air
VHF/UHF channels
Cab e
CABLE TV channe s
4
Press A/T to select"Automatic
Search", then press
ENTER.
The TV will begin memorizing all the channels available
in your area.
• It may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a BAR display
may not advance for several minutes, please be
patient.
• If you press EXIT in the process of "Auto Setup", the Auto
Setup stops and changes to the normal screen.
• When you make a menu selection, your changes occur
immediately.You do not have to press EXIT to see your
changes.
• When you are finished programming the menus, press
EXIT.
• If your cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although it may appear as though
the channel does not change, it actually moves from the
analog to the digital channel in sequence.
If you use channel-down,
it will move in reverse, from the
digital channel to the analog channel.
Method 2
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CATV/DIGITAL.
To select a 1 or 2-digit channelnumber(e. g., Channel 5):
Press 5
• When selecting
a 1-digit
channel
number,
it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection wil! be made
if there is no operation within a few seconds.
To select a 3-digit channel number(e. g., Channel 115):
Press 1_1_5
To select a 4-digit channel number(e. g., Channel 22.1):
Press 2_2_
° (DOT) _1
• When you enter 0-9 only, channel selection wil! be made
if there is no operation within a few seconds.
• If you press 0 by itself in "Air" reception,
nothing wil!
happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection wil!
be made if there is no operation within a few seconds.
(_=14
Advertisement
Table of Contents
