Advertisement
cabinet
To vent through
the roof or wall, mark 5-3/4"
and 6-1/4" in from back wall along the
centerline
on underside
of cabinet,
Use
these points as centers
to draw 7-1/8"
circles on underside
of cabinet,
Use a saber saw to cut the openings
for the
vent system, Repeat for the underside
of
the top of the cabinet,
This will create
slotted
openings
which
makes it easier to
install the vent system,,
Install vent system through
the vent
m opening
in upper cabinet
or wall,
Complete
venting
system according
to
method
needed,
See "Venting
requirements,"
Use caulking
to seal exterior
wall or roof opening,
If roof or wall cap does not
have a damper,
install damper
(supplied
with hood) in vent system to
prevent
air from flowing
back into vent
system,
If roof or wall cap has a damper,
Do Not use
damper
blade supplied
with range hood,
Do Not turn on power
until
m installation
is complete.
Run
wiring through
wall or cabinets
according
to the National
Elecfrbal
Code
and local
codes and ordinances,
Use caulking
to seal
ceiling
or outside wall opening,
four keyhole mounting
screw slots marked
on the cabinet
bottom,
keyho
Check
that
,?;--JA
o,,,o,.
X
_
front of hood
screw
Lift range hood into final
m position,
feeding
electrical
wire
through
wiring opening,
Tighten mounting
screws to cabinet,
making
sure mounting
screws are in narrow neck of slot,
Electrical
Shock Hazard
Disconnect
power before making
electrical
connections.
Connect
ground wire to green ground
screw in terminal
box.
Failure to do so can result in death or
electrical
shock.
Panel C
white
For models
requRing
dRect wiring:
Connect
the white and black wires of the
power
supply cable
to the white and black
leads in the range hood with twist-on
connectors,
Connect
the power
supply grounding
wire
to the green,
grounding
screw inside the
range hood terminal
box,
Use caulking
to seal wire opening,
Replace
terminal
box cover,
For cord
connected
models:
EJectrica! Shock Hazard
Plug into a grounded
3-prong outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instructions
can
result in death, fire, or electrical
shock.
For your personal
safety, this range hood
must be grounded,
To minimize possible
shock hazard, the cord must be plugged
into a mating,
3-prong,
ground-type
outlet,
grounded
in accordance
with National
Electrical
Code, ANS!/NFPA 70 - latest
edition*
and all local codes and
ordinances,
If mating outlet is not available,
if is the
responsibility
and obligation
of the customer
to have a properly
grounded,
3-prong
outlet installed by a qualified
electrician,
Do not use an extension
cord,
Using a U.L.-listed
power
supply
cord-connection
kit:
Follow Power Cord Kit instructions
for
connecting
wiring.
Replace
terminal
box cover,
For models
with a factory
installed
power
cord:
Plug power
cord into grounded
3-prong
outlet,
_m
Turn power supply on,
Copies of standards listed may
be obtained from:
" National
Fire Protection
Association
Bafterymorch
Park
Quincy,
Massachusetts
02269
make reinstalling
your
range hood inanother
home
as easy as the first
installation.
of tan e
For best results, turn range hood fan ON at
beginning
of cooking
and allow it to run
until all smoke and odors are removed
from
room,
To turn fan ON and OFF:
Press fan control to turn fan on and off and
adjust fan speed,
Speed may be increased
or decreased
anytime
during range hood
operation,
To turn range hood light ON and OFF:
Press light control to turn light on or off, Light
may be turned
off or on anytime
during
range hood operation,
Care of
¢
Fitter/light
lens:
For best results, remove
and dean
often,
To remove
filter/light
lens:
/
/
tilter tab
Pull firmly on filter tab to remove
filter/light
lens from range hood,,
To clean
filter/light
lens:
Place filter/light
lens in dishwasher
or hot
sudsy wafer to dean,
To reinstall filter/light
lens:
Place edge
of filter/light
lens in opening
so
that right side is above
flange
and tab
faces downward,
Press filter/light
lens into
position,
When it's time to replace
your
aluminum
filter/light
lens:
1, Model series RH2000X:,
Order Filter/Light
Lens no, 883149
2, Call Whirlpool's Telesales line at
1-800-442-9991
3, Give the Telesales Representative
the
part number
needed,
4, The Representative
will give you the
current price,
5, Place your order using your Master
Card ®_, V isa ®_ or Discover ®) c redit card,
6, If you wish: mail a check
or money order
to:
Whirlpool
Corporation
1900 Whirlpool
Drive
LaPorfe, IN 46350-9980
Attn: Accessory
Accounting
Be sure to ask the Telesales
Representative
about
the wide variety
of
other Whirlpool
Product Accessories,
To clean
fan motor:
Every three years lubricate
each
motor
bearing
with a few drops of oil to help
prolong
motor life,
Clean exterior of motor with a damp
cloth
and grease-cutting
detergent,
Exterior surfaces
Clean the range hood with a mild
detergent
and soft cloth, Do Not use
abrasive
cleansers
or steel wool pads,
Light
Do Not use bulb larger than 60 watts in light
socket,
Light bulb is not included,
Advertisement
