Refrigerator Doors - Whirlpool WRT111SFAW00 User Instructions

7. Slip thecompression sleeve a nd compression nutonthe
copper tubing asshown. Insert theend ofthetubing intothe
outlet e nd squarely asfarasitwill g o.Screw compression nut
ontooutlet endwithadjustable wrench. Donotovertighten.
8. Place t hefree end ofthetubing i nacontainer orsink, a nd turn
ON themain water supply. Flush t hetubing u ntil w ater i sclear.
Turn OFF theshutoff valve onthewater p ipe. C oil t hecopper
tubing.
Connect to Refrigerator
NOTE: On kit models, assemble water valve to refrigerator
according to kit instructions.
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.
3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid
damage to the tubing when the refrigerator is pushed back
against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
A
B
C
6.
A. Tube clamp
B. Tube clamp screw
C. Copper tubing
D. Compression nut
E. Valve inlet
The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the 1/4"(6.35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.
3.
4.
Style 2
1. Unplug refrigerator or disconnect power.
2. Disconnect the tube clamp on the back of the product and
insert the copper tubing through the clamp as shown.
Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown.
Tighten the compression nut. Do not overtighten. Reattach the
tube clamp and tube to the back of the cabinet.
A
B
C
5. Turn shutoff valve ON. Check for leaks. Tighten any
connections (including connections at the valve) or nuts that
leak.
6.
The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the 1/4"(6.35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.
Complete the Installation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
Refrigerator Doors
TOOLS NEEDED: _e" hex-head socket wrench, #2 Phillips
screwdriver, flat-blade screwdriver, 5/le" open-end wrench, flat
2" putty knife.
IMPORTANT:
• Before you begin, turn the refrigerator control OFE Unplug
refrigerator or disconnect power.
• Remove food and adjustable door or utility bins from doors.
• If you are only removing and replacing the doors, see the
"Remove Doors and Hinges" and "Replace Doors and
Hinges" sections.
Remove Doors and Hinges
5_6"
Hex-Head Hinge Screw
1=
2.
3.
Unplug refrigerator or disconnect power.
Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE: Provide support between the freezer and refrigerator
doors while the hinges are being moved. Do not depend on
the door magnets to hold the doors in place while you are
working.
Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.
A. Tube clamp C. Compression nut
B. Copper tubing