Whirlpool ER8AHKXRL00 Use & Care Manual page 5

Connect to Refrigerator
NOTE: On kit models, assemble water valve to refrigerator per kit
instructions.
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut, Do not
overtighten.
3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help prevent
damage to the tubing when the refrigerator is pushed back
against the wall.
4. Turn shutoff valve ON,
5. Check for leaks, Tighten any connections (including
connections at the valve) or nuts that leak,
Complete the Installation
Electrica_ Shock Hazard
P_ug into a grounded 3 prong outlet.
Do not remove ground prong,
Do not use an adapter,
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or eiectrica_ shock,
C
D
6=
A. Tube clamp
B. Copper tubing
C. Compression nut
D. Valve inlet
The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the 1/4"(6,35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.
Style 2
1. Unplug refrigerator or disconnect power.
2. Disconnect the tube clamp on the back of the product and
insert the copper tubing through the clamp as shown.
3. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown.
4. Tighten the compression nut. Do not overtighten. Reattach the
tube clamp and tube to the back of the cabinet,
A. Tube clamp C. Compression nut
B. Copper tubing
5. Turn shutoff valve ON, Check for leaks. Tighten any
connections (including connections at the valve) or nuts that
leak,
6. The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the 1/4"(6.35 mm) water line at either tube connection, Obtain
a water strainer from your nearest appliance dealer.
Plug in refrigerator or reconnect power.
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
TOOLS NEEDED: %6" hex-head socket wrench, #2 Phillips
screwdriver, flat-blade screwdriver, %6" open-end wrench, flat
2" putty knife.
IMPORTANT:
• Before you begin, turn the refrigerator control OFE Unplug
refrigerator or disconnect power.
• Remove food and adjustable door or utility bins from doors.
• If you are only removing and replacing the doors, see the
"Remove Doors and Hinges" and "Replace Doors and
Hinges" sections,
• Depending on your model, you may have standard (Style 1) or
contour (Style 2) doors, If you are also going to reverse the
door swing, follow the instructions for the appropriate door
style.
Remove Doors and Hinges
5/16" Hex-Head Hinge Screw
1. Unplug refrigerator or disconnect power.
2. Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet,
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Remove the parts for the top hinge as shown in Top Hinge
graphic, Lift the freezer door free from the cabinet,
4. Remove the parts for the center hinge as shown in the Center
Hinge graphic, Lift the refrigerator door free from the cabinet.
5. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.