Sharp AQUOS LC-60LE820UN Operation Manual page 49

Using a PC
AQUOS
NET DOCK
1 Press MENU to display the MENU screen, and then
press 4/1_ to select "System Options".
2 Press A/V to select "Input Terminal Setting", and
then press ENTER.
3 Press A/T to select "PC input", and then press
ENTER.
4 Press A/V to select a specific adjustment item,
and then press ENTER to set each item.
5 Press A/Y (or 4/1_) to select or adjust the desired
setting, and then press ENTER.
This function sets the terminal to output the computer
audio.
The adjustment items vary depending on the input
source. Select the input source corresponding to the
terminal connected to the PC and then adjust the
desired item.
iNPUT 3
Video: Select this when the TV and PC are connected
using an analog RGB cable and the audio is not input.
Video+Audio: Select this when the TV and PC are
connected using an analog RGB cable and the audio is
input via a ® 3.5 mm stereo minijack.
m iNPUT 4
HDMl(Digital): Select this when the TV and PC are
connected using an HDMI-certified cable and audio is
input via the same cable.
HDMl+Analog: Select this when the TV and PC are
connected using a DVI-HDMI conversion cable and the
audio is input via a ® 3.5 mm stereo minijack.
For automatically adjusting the PC image.
Yes: Auto Sync. starts and "Now adjusting the image."
displays.
No: This function does not work.
= When "Auto Sync." is successful, "Completed" displays. If
not, "Auto Sync." failed.
= "Auto Sync." may fail even if "Completed" displays.
o "Auto Sync." may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing "Auto Sync.".
o Be sure to connect the PC to the TV and switch it on before
starting "Auto Sync.".
Ordinarily you can easily adjust the picture as necessar
to change image position using "Auto Sync.". In some
cases, however, manual adjustment is needed to
optimize the image.
N-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
o For resetting all "Fine Sync." adjustment items to the factor
preset values, press A/Y to select "Reset", and then press
ENTER.
o It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
o The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
o The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
o When "Audio Select" is set to "HDMl(Digital)", sound will
not be produced if you use only an HDMI-certified cable to
connect HDMI-compatible equipment. To produce sound,
you should make an analog audio connection.
o If you want to connect HDMI-compatible equipment
using only an HDMI-certified cable, set "Audio Select" to
"H DMl(Digital)".
It is necessary to set the PC correctly to display XGA
and WXGA signal.
VGA
Horizontal Vertical VESA
Resolution
Frequency Frequency Standard
720 x 400 31.5 kHz 70 Hz
31.5 kHz 60 Hz O
640 x 480 37.9 kHz 72 Hz O
37.5 kHz 75 Hz O
35.1 kHz 56 Hz O
37.9 kHz 60 Hz O
SVGA 800 x 600
48.1 kHz 72 Hz O
46.9 kHz 75 Hz O
48.4 kHz 60 Hz O
XGA 1024 x 768 56.5 kHz 70 Hz O
60.0 kHz 75 Hz O
WXGA 1360 x 768 47.7 kHz 60 Hz O
SXGA 1280 x 1024 64.0 kHz 60 Hz O
SXGA+ 1400 x 1050 65.3 kHz 60 Hz O
UXGA 1600 x 1200 75.0 kHz 60 Hz O
1080p 1920 x 1080 67.5 kHz 60 Hz
VGA and XGA are registered trademarks of International |
Business Machines Corp.
l
Q- 48