Additional Recording Operations - Pioneer CT-WM62R Operating Instructions Manual

IREcoRDING (DECK I)
3. Press the OPEN/CLOSE button to close the tray.
4. Press one of the CASSETTE NUMBER buttons to
load the cassette for recording.
5. Select the desired tape transport mode with the
REVERSE MODE button.
• To record on both sides of the tape, select "C.Y' (reverse
mode).
• To record on only one side of the tape, select "z" (one
way mode).
6. Select the desired type of Dolby noise reduction
with the DOLBY NR buttons (see below).
7. Press the recording (e) button to enter recording
standby mode.
8. Adjust the recording level using the REC LEVEL
control knob.
With the amplifier, select the audio source you wish to
record and use the REC LEVELcontrol knob to adjust the
recording level (see ADJUSTING THE RECORDING LEVEL,
page 17).
9. Start recording by pressing the appropriate play (1_
or <) button or the pause
(11)
button.
One way mode recording (Z)
Press the forward play (1_) button to record on side A. Press
the reverse play (_1) button to record on side B.
Reverse mode recording (o)
Press the forward play (1_) button to begin recording on both
sides.
If the reverse play (<1) button is pressed, recording will stop
after only one side is recorded.
NO TES:
• If the pause (11)button is pressed, recording will begin. The
tape transport direction will be the direction displayed by
the tape transport indicators when the button is pressed.
• During recording, the CASSETTE RETURN and CASSETTE
NUMBER buttons do not operate.
• The cassette deck will not record on tapes whose erasure
prevention tabs have been removed. Make sure that the
tabs are intact before loading the tape for recording. If the
tabs have been removed, put a piece of adhesive tape over
the hole (see page 7).
To stop recording:
Press the stop (i) button.
To pause recording:
Press the pause (11) button. To resume recording, press the
pause button again or press the appropriate play (1_ or <)
button.
ADDITIONAL RECORDINGOPERATIONS
SEI-rlNG THE DOLBY NR SYSTEM
This cassette deck allows you to preprogram a different Dolby
NR setting for each tape in DECK I. This lets you perform relay
recording or relay playback of tapes with different types of
Dolby NR.
The Dolby NR setting of DECK II is selected with the same
buttons.
• To check the currently programmed Dolby NR settings:
Press the DOLBY NR MEMORY button. The current settings
appear on the display.
EXAMPLE:
The sample display below indicates the following preprog-
rammed Dolby NR selections:
tape 1: B-type, tape 2: off, tape 3: C-type, tape 4: B-type, tape 5:
C-type, tape 6: off, DECK I1:C-type.
r_ (Lighted)
r-_ I iiiiiiii lUlllll
f
//J=_=_\ IIIIIIII IIIIIIII IIInlll
(Flashing)
Programming the Dolby NR settings of each tape
(DECK I, DECK II)
1. Press the DOLBY NR MEMORY button.
• The currently programmed settings are displayed.
2. Press the DOLBY NR OFF/B/C button repeatedly
until the desired setting is displayed. (The DOLBY
type to be memorized will flash.)
16
<RRB1134>
En
3. Press one of the CASSETTE NUMBER buttons.
• The selected tape is programmed to record or playback
with the type of Dolby NR selected in step 2.
4. Repeat steps 2 and 3 for the other tapes on the tray.
5. To set the Dolby NR for the tape in DECK II, press
the DOLBY NR OFF/B/C button repeatedly until the
desired setting is displayed. (The DOLBY type to be
memorized will flash.)
6. Press the stop (i) button of DECK I1.
To change the Dolby NR setting during recording or playback:
Press the DOLBY NR OFF/B/C button until the desired setting is
displayed. The memorized setting for the tape which is cur-
rently being recorded or played back will also change.
• During tape copying, only the Dolby NR setting of the
playback tape will change.
To change the Dolby NR setting during stop mode:
Press the DOLBY NR OFF/B/C button until the desired setting is
displayed. The current Dolby setting changes and the me-
morized setting for the currently loaded tape will change.
• The tape transport -r-l-J- and "l-n'-I" indicators and
cassette number indicators display the location of the
cassette whose Dolby NR setting has been changed.
NOTES
• The DOLBY NR MEMORY button switches the level meter
from normal (audio level) display mode to Dolby NR
memory display mode.
• During the Dolby NR setting procedure, none of the other
operation buttons will function.