Table of Contents
Advertisement
VCR
Plus+ Set Up
programming only.
VCR Plus+ programming allows you to set most items of a timer recording by simply entering a special code found in IV GUIDE
magazine as well as the TV listings in selected newspapers. In order for the VCR to read this special code, some set up is required.
A Guide (VCR Plus+) channel number is assigned to each local broadcast and cable station. Because this number sometimes
differs from the channel your TV receives the station on, it is necessary to program the VCR with local channel information.
O
,,,_L,o, j
oT,v,_,p,. ,,_,o
OO
°6T8'
O
O
O
Channel Set Up Preparations
NOTE: Complete the steps on this page if you are using
Connection Method 2 on page 10 for VCR hookup.
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step 4 at right.
You will need the following to complete the list:
• A line up of normal and/or cable stations you
receive along with the channel numbers your TV
receives them on. A cable channel line-up chart is
supplied by your cable company.
• A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found in
selected newspapers.
1
Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2 In the middle column, fill in each station's
assigned Guide (VCR Plus+) number found in TV
Guide, newspapers, etc.
3 In the right column, fill in the channel number that
y.ourTV receives the station on from your channel
line-up.
EXAMPLE ONLY
Broadcast or Cable
Station Name
HBO
Nickelodeon
CBS
FOX
Assigned
Guide
(VCR Plus+)
channelno.
33
38
04
11
26
Channel
no.
your TV
recelvesthe
station on
15
20
04
VCR Plus+ Channel Set Up
(Connection
Method 2 on page 10)
O
Push MENU
to display the
MENU
menu.
O
Rotate and push
the WHEEL to
select SET UP
CHANNEL.
---
MENU
---]
SET
UP VCR
I
IDIOMA/LANGUE:ENGLISH
I
SELECT
ROTATE
WHEEL
I
ISET
PUSH WHEEL
I
[END
PUSH MENU KEY
J
O
Rotate and push
the WHEEL to
select VCR Plus+
CH SET UP.
IMPORTANT NOTE:
---
SET
UP CHANNEL
---
ANTENNA
SYSTEM
:
CATV
AUTO SET
ISELECT
ROTATE
WHEEL
ISET
PUSH WHEEL
[END
PUSH MENU
KEY
For this step, use the list you prepared. You may leave lines
blank if, you don't receive that station, or the GUIDE CH
number and the CATV (or TV) CH numbers are the same.
O
Push WHEEL
to move the
shaded area on
the right side.
l
VCR
Plus+
CH SET
UP
GUIDE CH
CATV CH
-,_
_--
SELECT
ROTATE WHEEL
/
SET
PUSH WHEEL
END
PUSH MENU KEY
Then,
rotate
the Wheel
to change
CATV or TV CH number.
Next, push the Wheel
to enter CATV or TV CH number.
Now, rotate
the Wheel
to continue.
Repeat this operation
until the list is complete.
To Make Corrections
Rotate and push the Wheel to select the incorrect CATV or TV
CH number. Then, Push CLEAR to delete the numbers.
Now, use the Wheel to re-enter the channel.
Push MENU
twice to exit the
VCR Plus+ CH
SET UP mode.
;Make
yourentrieswithin60 secondsor the VCR will
_ _
leave thismode.
....
• Once localchannelshavebeen programmed, t hey Will
stayin memory, even in the case of a powerfailure.
CR P us+C 3and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
nder license from Gemstar Development Corporation.
_)
Advertisement
Table of Contents
