Table of Contents
Advertisement
Installation
Television
Location
Follow
these
recommendations
before
deciding
the
location of your television.
Avoid
excessive
sunlight
or
bright
lights,
including
reflections.
Keep away
from excessive
heat or moisture.
Inadequate
ventilation
may cause
internal
component
failure.
Fluorescent
lighting
may
reduce
remote
control
transmitting
range.
Keep
away
from magnetic
equipment,
including
motors,
fans and external
speakers.
WARNING:
Use this television
receiver
only with the
cart,
stand,
tripod,
bracket,
or table
specified
by the
manufacturer,
or sold with the apparatus.
When
a cart
is used,
use caution
when moving
the cart/apparatus
combination
to avoid
injury from tip-over.
In order
to
avoid
injury to children,
never
place
your television
receiver
on a
piece of furniture
that is capable
of being
tilted by a child
leaning
on it, pulling
on it, standing
on it, or climbing
on it. A falling
television
can cause serious
injury or even death.
CT-27SL14,
CT-27SL14U:
CAUTION:
These
television
receivers
for
use
only
with
PANASONIC
TY-27SL33T
stand.
Use
with
other
carts
(or
stands)
is capable
of resulting
in instability
causing
possible
injury.
CT-32SL14,
CT-32SL14U:
CAUTION:
These
television
receivers
for
use
only
with
PANASONIC
TY-32HL43T
stand.
Use
with
other
carts
(or
stands)
is capable
of resulting
in instability
causing
possible
injury.
CT-36SL14,
CT-36SL14U:
CAUTION:
These
television
receivers
for
use
only
with
PANASONIC
TY-36HL43T
stand.
Use
with
other
carts
(or
stands)
is capable
of resulting
in instability
causing
possible
injury.
Optional
Cable
Connections
Shielded audio and video cables should be used between
components. For best results:
Use 75-ohm
coaxial
shielded
cables.
Use appropriate
input and output
connectors,
that match
your component
connectors.
Avoid
long cables
to minimize
interference.
AC Power
Supply
Cord
CAUTION:
TO PREVENT
ELECTRIC
SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT
OF AC OUTLET
AND FULLY INSERT.
DO NOT
Polarized plug
USE A PLUG WITH A RECEPTACLE
OR OTHER
OUTLET
UNLESS
THE
BLADE
CAN
BE
FULLY
INSERTED
TO
PREVENT BLADE EXPOSURE.
PROTECT
POWER
CORDS
FROM
BEING
WALKED
ON,
ROLLED
OVER, CRIMPED,
BENT, OR PINCHED,
PARTICULARLY
AT PLUGS,
CONVENIENCE
RECEPTACLES,
AND THE POINT WHERE THEY EXIT
FROM THE APPARATUS.
Cable / Antenna
Connection
For proper reception, either a cable or antenna connection
is required.
Cable Connection
Incoming
Cable from
Cable Company
Connect
the cable
supplied
by your
local
cable company.
Tighten
with
fingers
only.
Use
of any tool
(e.g.
pliers)
for tightening
may result
in tuner damage.
Note:
A cable
converter
box
may
be
75 Ohm VHF/UHF
on back of TV
required
for
proper
reception.
Check
with
your
local
cable
company
for compatibility
requirements.
Antenna
Connections
For proper
reception
of VHF/
Incoming Cable from
UHF
channels,
an
external
Home Antenna
antenna
is required.
For best
reception
an outdoor
antenna
is recommended.
Note:
Cable
Mode
is
preset
at
the
factory.
Antenna
users
must
change
to TV Mode
in the Set
Up menu
under
Prog
Chan (page
13).
Remote
Control
Battery
Installation
Requires two AA batteries (supplied).
Battely
Polarity
®
Procedure
1.
Turn the remote
control face
down.
Remove
battery
cover
by pressing
down
on the marking
on the cover
and sliding
it off in the direction
indicated.
2.
Install batteries
matching
(+) and (-) polarity
signs.
3.
Replace
the battery
cover by sliding
in reverse
until the
lock snaps.
Note:
Incorrect
installation
can cause
battery
leakage
and
corrosion that will damage the Remote Control.
Precautions
Replace batteries in pair.
Do not mix battery types (zinc carbon with alkaline).
Do not recharge,
heat, short-circuit,
disassemble,
or
burn batteries.
4o
Hide quick links:
Advertisement
Table of Contents
