Lawn Mower; Drive Wheels; Grass Catcher; Gear Case - Craftsman 917.377782 Owner's Manual

LAWN MOWER
Alwaysobservesafetyruleswhen per-
formingany maintenance.
TIRES
o Keeptires free of gasoline,oil, or insect
controlchemicalswhichcanharmrubber°
° Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage_
DRIVE WHEELS
Check rear drive wheels each time you
mow to be sure they move freely. The
wheels not turning freely means trash,
grass cuttings, etc., may be inside the
drive wheel and dust cover area and must
be cleaned out to free drive wheels.
If necessary to clean the drive wheels,
check both rear wheels°
BLADE CARE
For best results, mower blade must be kept
sharp. Replace a bent or damaged blade.
TO REMOVE BLADE
1, Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug.
2, Turn lawn mower on its side° Make
sure air filter and carburetor are up,
3o Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt,
NOTE: Protect your hands with gloves
andtor wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5, Remove blade and attaching hardware
(bolt, lock washer, hardened washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade adapter,
The key must be in good condition to work
properly. Replace adapter if damaged,
TO REPLACE BLADE
I, Position the blade adapter on the en-
gine crankshaft. Be sure key in adapter
and crankshaft keyway are aligned,
2. Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
3. Be sure the trailing edge of blade (oppo-
site sharp edge) is up toward the engine.
4o Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft,
5, Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
* The recommended tightening torque is
35-40 ft. Ibs_
IMPORTANT: Blade bolt is heat treated.
If bolt needs replacing, replace only with
approved bolt shown in ttle Repair Parts
section of this manual,
Blade adapter Crankshaft
keyway
Key -....
kwasher
Blade
Blade Crank
bolt shaft
washer Trailing edge Blade adapter
TO SHARPEN BLADE
NOTE: We do not recommend sharpening
blade - but if you do, be sure the blade
is balanced, balanced. An unbalanced
blade will cause eventual damage to lawn
mower or engine,
° The blade can be sharpened with a fife
or on a grinding wheel, Do not attempt
to sharpen while on the mower.
• To check blade balance, drive a nail into
a beam or wall. Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail.
If blade is balanced, it should remain in
a horizontal position, if either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
GRASS CATCHER
• The grass catcher may be hosed with
water, but must be dry when used.
• Check your grass catcher often for dam-
age or deterioration. Through normal
use it will wear, tf catcher needs replac-
ing, replace only with approved replace-
ment catcher shown in the Repair Parts
section of this manual. Give the lawn
mower model number when ordering.
GEAR CASE
• To keep your drive system working
properly, the gear case and area around
the drive should be kept clean and free
of trash build-up, Clean under the drive
cover twice a season.
• The gear case is filled with lubricant to the
proper level at the factory° The only time
the lubricant needs attention is if service
has been performed on the gear case,
- If lubricant is required, use only Texaco
Starplex Premium 1 Grease, Part Noo
750369. Do not substitute,
13