18.5 hp, 42" mower electric start automatic transmission (57 pages)
Summary of Contents for Craftsman 917.273661
Page 1
Call: Read and follow all 1-800-659-5917 Safety Rules and Instructions Sears Craftsman Help Line before operating this equip- 5 am - 5 pm, Mon- Sat ment, Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman website: www.sears.com/craftsman...
Page 2
Repair Parts ......... MaintenanceSchedule......15 Sears Service ......Back Cover LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment maintained, lubricated and tuned up according to the instructions in the owner's...
IMPORTANT:This cutting machineis capableof amputatinghands andfeet and throw- ing objects.Failureto observethe followingsafety instructionscould result in serious injury or death. _WARNING: In order to preventac- • Be aware of the mower discharge direc- cidentalstarting when setting up, trans- tion and do not point it at anyone. porting,adjustingor making repairs, not operate the mower...
Page 4
• Never carry children. They may fall off and be seriously injured or interfere with • Mow up and down slopes, not across. safe machine operation. • Remove obstacles such as rocks, tree • Never allow children to operate limbs, etc.
• Removeobstacles such as rocks,tree • Be sure the area is clear of other people limbs,etc. before mowing.Stop machineif anyone enters the area. • Watchfor holes,ruts, or bumps.Uneven terrain could overturnthe machine.Tall • Nevercarry passengersor children evenwith the bladesoff. grass can hide obstacles. •...
Page 6
Some limitations and exclusions apply. For prices and additional information Congratulations on making a smart pur- call 1-800-827-6655. chase.Your new Craftsman® product is designed and manufactured for years of SEARS INSTALLATION SERVICE dependable operation. But like all products, For Sears professional...
Page 7
Yournewtractor has been assembledat the factory. Reviewthe video cassette before you begin. When right or left hand is mentionedin this manual,it meanswhen you are in the operatingposition (seatedbehindthe steering wheel). Adjustment Knob REMOVE TRACTOR FROM CARTON UNPACK CARTON Cut along dotted lines on all four pan- els of carton.
Page 8
5. Place motion control lever in neutral ,/CHECKLIST (N) position. Before you operate your new tractor, 6. Press lift lever plunger and raise wish to assure that you receive the best attachment lift lever to its highest posi- performance and satisfaction from this tion.
Page 9
These symbols may appearon your tractoror in literaturesupplied with the product, Learn and understandtheir meaning. I'.,I REVERSE NEUTRAL HIGH CHOKE FAST SLOW IGNITION ® ENGINE OFF LIGHTS ON ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE LOCKED UNLOCKED OVER TEMP FUEL OIL PRESSURE...
Page 10
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. ht Switch Position Attachment Clutch Switch Ignition Switch Lift Lever Plunger...
Page 11
The operation of any tractor result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety SAFETYGLASSES glasses or eye shields while operating your tractor or performing adjustments or repairs. We recommend standard safety glasses or a wide vision safety...
Page 12
TO ADJUST GAUGE WHEELS TO OPERATE ON HILLS Gauge wheels are properly adjusted AQ_,WARNING: Do not drive up or down when they are slightly off the ground when hills with slopes greater than 15 ° and do mower is at the desired cutting height not drive across...
Be sure freewheel control is in the BEFORE STARTING ENGINE transmission engaged position. CHECK ENGINE OIL LEVEL Sit on seat in operating position, The engine in your tractor has been depress clutch/brake pedal and set shipped, from the factory, already filled parking brake.
3. Allow one minute for transmission Slowly move motion control lever for- warm up. This can be done during ward, after the tractor moves approxi- engine warm up period. mately five (5) feet, slowly move motion • The attachments can be used during control lever to reverse position.
FILL IN DATES AS YOU C 0 M PLETE J__/,"_ _.J_ REGULAR SERVICE _'_K_'4r_'fSERVlCE DATES Check Brake Operation Check Tire Pressure Check Operator Presence Interlock Systems Check for Loose Fasteners Sharpen/Replace Mower Blades li_s Lubrication Chart Check Battery Level Clean Battery and Terminals Check...
Page 16
TRACTOR IMPORTANT: To ensure proper assembly, center hole in blade must align with star Always observe safety rules when per- on mandrel assembly. forming any maintenance. Install and tighten blade bolt securely BRAKE OPERATION (45-55 Ft. Lbs. torque). If tractor requires more than five (5) feet to IMPORTANT:...
Page 17
NOTE: The original equipment battery SAE VISCOSITY GRADES your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte not necessary. TO CLEAN BATTERY AND TERMINALS oil vJ cchart4 Corrosion and dirt on the battery Change the oil after every 50 hours of op-...
ENGINEOIL FILTER CLEAN AIR SCREEN Replacethe engine oil filter every season Air screen must be kept free of dirt and or everyother oil change if the tractor is chaff to prevent engine damage from usedmore than 100hours in one year. overheating.
Page 19
CLEANING We do not recommend using a garden hose or pressure washer to clean your • Clean engine, battery, seat, finish, etc. tractor unless the engine and transmis- of all foreign matter. sion are covered to keep water out. Water •...
Page 20
Slide mower under tractor with deflec- • Using the lift lever, place mower tor shield to right side of tractor. position where no part of the mower, IMPORTANT: Check belt for proper rout- including gauge wheels, is touching ing in all mower pulley grooves.
Page 21
BOTH FRONT PLATE LINKS MUST BE Suspension EQUAL IN LENGTH Lift Link Adjustment FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side- Nut "C" to-side. If the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.
Page 22
R.H. Mandrel Cover BeltTension Rod (Disengaged Position) _ ji7 Clutch Pulley Idler Pulleys Mandrel Spring Arm R.H. Sus Primary Idler Arm TO REPLACE MOWER BLADE 10. Check secondary idler arm and idler pulley to see that they rotate freely. (SECONDARY) DRIVE BELT 11.
Page 23
Secondary Idler Idler Arm Pulley Secondary Spring Arm Center L.H. Mandrel Mower Blade (Secondary) Drive Belt R.H. Mandrel TO CHECK AND ADJUST BRAKE With parking brake "Engaged" Your tractor is equipped with an adjustable _Njat "A" brake system which is mounted on the right side of the transaxle.
Page 24
3. Pull belt towardfront of tractorand roll NOTE: To seal tire punctures and prevent belt around electricclutch and onto flat tires due to slow leaks, purchase engine pulley. use tire sealant from Sears. Tire sealant 4. Install belt through stationaryidler and also prevents tire dry rot and corrosion.
Page 25
REPLACING BATTERY Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of _WARNING: Do not short battery termi- tractor. nals by allowing a wrench or any other object to contact both terminals at the same time. When replacing hood, be sure to re-...
Page 26
TO ADJUST CHOKE CONTROL FINAL SETTING The choke control has been preset at the 1. Start engine and allow to warm for five factory and adjustment should not be nec- minutes. Make final adjustments with essary, check adjustment as described engine running and shift/motion...
Page 27
Immediatelyprepareyour tractor for stor- blended fuels (called gasohol or using age at the end of the season or if the trac- ethanol or methanol) can attract moisture tor will not be usedfor 30 days or more. which leads to separation and formation _IkWARNING: Never store the tractor...
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. Fill fuel tank. See "TO START ENGINE" Engine not "CHOKED" properly. Operation section. 3. Wait several minutes before Engine flooded.
Page 29
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Loss of power Faulty spark plug. Clean and regap or change (continued) spark plug. Dirty fuel filter. Replace fuel filter. Stale or dirty fuel. Empty fuel tank and refill tank with fresh, clean gasoline.
Page 30
TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center CAUSE PROBLEM CORRECTION 3. Wet grass• Poor grass 3. Allow grass to dry before discharge mowing. Mower deck not level. Level mower deck. (continued) Low/uneven tire air pressure. Check tires for proper pressure.
Page 31
TRACTOR - - MODEL NUMBER 917.273661 SCHEMATIC BLACK BATTERY SOLENOID STARTER BLACK ELECTRIC CLUTCH CLUTCH / BRAKE (PEDAL UP) SEAT SWITCH NOT OCCUPIED) PTO (DISENGAGED) GROUNDING CONNECTOR BLUE BLACK (OPTIONAL) SPARK PLUGS IGNITION UNIT (2 PLUGS ON TWIN CYL ENGINES) CHARGING SYSTEM OUTPUT...
Page 32
TRACTOR - - MODEL NUMBER 917.273661 ELECTRICAL...
Page 33
TRACTOR - - MODEL NUMBER 917.273661 ELECTRICAL KEY PART DESCRIPTION 144927 Battery 74760412 Bolt, Hex 1/4-20 x 3/4 7603J Tray, Battery 145211 Bolt, Battery, Front 1/4-20 x 7-1/2 150109 Holddown, Battery, Front 145769 Nut, Push, Nylon, Battery, Front 1/4 176138 Switch, Interlock 175688...
Page 34
TRACTOR - - MODEL NUMBER 917,273661 CHASSIS AND ENCLOSURES lO.4 209"_ j209 4 44 >209 chassis-stealth,stlt...
TRACTOR - - MODEL NUMBER 917,273661 GROUND DRIVE 1202 165 156 24 ./_ drive-hydro,stlt...
Page 37
TRACTOR - - MODEL NUMBER 917.273661 GROUND DRIVE PART PART DESCRIPTION DESCRIPTION Transaxle, HydroGear, Model 174607 Pulley, Engine Washer Number 314-0510 (See Break 10040700 down) 154778 Keeper Belt Engine 165866 Rod Shift Fend. 169183 Strap Torque 179334 Clutch Electric 169182 Strap Torque 76020416 Pin Cotter...
TRACTOR - - MODEL NUMBER 917,273661 MOWER DECK 122- mower deck.48prem stlt...
Page 47
TRACTOR - - MODEL NUMBER 917,273661 MOWER DECK PART PART DESCRIPTION DESCRIPTION 180358 Deck Weldment Mower 74780616 Bolt Fin Hex 3/8-16 uncx 1 Gr. 5 138017 Bracket Asm., Sway Bar 72140608 Bolt Rdhd Sqnk 3/8-16 unc x 1 4939M Retainer Spring 155986 Bar Pnt Adj.
Page 48
"'1- _,-.I r-.t , NI wl.- €.n .,_ r124 ",,,4 u108 _125 SEALANT 20W50 78.80Z 127- SEAL O-RING...
Page 49
TRACTOR - - MODEL NUMBER 917.273661 HYDRO GEAR TRANSAXLE - - MODEL NUMBER 314-0510 PART PART DESCRIPTION DESCRIPTION 170351 Main Housing, Assembly 170408 Rotor, Brake 170352 Side Housing, Assembly 142883 Brake Puck 170353 Center Section, Assembly 142882 Puck Plate 170354 Swashplate, Trunion Machined 142887 Brake Actuating Pin...
Page 50
TRACTOR - - MODEL NUMBER 917.273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 CYLINDERHEAD, VALVEAND BREATHER CRANKCASEJ 23_@ I c._ ¸¸¸¸¸¸¸22 20-- O--¸19 y" 15/.
Page 51
TRACTOR - - MODEL NUMBER 917,273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 CRANKCASE HEADNALVEIBREATHER PART PART DESCRIPTION DESCRIPTION Seal, front oil 24-033-03-S Kit, breather cover w/gasket 24-032-01-S Crankcase (Includes 2-4) (USE: Miniblock 24 782 24) 24-041-50-S Gasket, breather Fitting 24-096-87-S Cover, breather 24-294-13-S Pin, locating (6)
Page 52
TRACTOR - - MODEL NUMBER 917,273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 IGNITION/ELECTRICALJ BLOWER HOUSING BAFFLES _--4 AIR INTAKE...
Page 53
TRACTOR - - MODEL NUMBER 917,273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 BLOWER HOUSING & BAFFLES IGNITION/ELECTRICAL PART PART DESCRIPTION DESCRIPTION 24-027-114-S Housing, blower 54-755-15-S Kit, grass screen (Incl. 2, 24-096-85-S & 25- (Includes 2-4,and 24 113 18- 086-91-S) 24-100-01-S Nut plastic (2) M-403025-S Screw, hex.
Page 54
TRACTOR - - MODEL NUMBER 917.273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 ® OIL PAN / LUBRICATION...
Page 55
TRACTOR - - MODEL NUMBER 917,273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 OIL PAN/LUBRICATION STARTING SYSTEM PART PART DESCRIPTION DESCRIPTION 24-199-07-S Pan assembly, oil M-839080-S Screw, hex. flange (Includes 2-12,16) M8x1.25x80 (2) 24-393-37-S Oil pump assembly (Includes 25-098-09-S Starter, solenoid shift assem 3,4) bly (Includes 3-7) 24-381-11-S...
Page 56
TRACTOR - - MODEL NUMBER 917,273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 EXHAUST CRANKSHAFT 2--@ FUEL SYSTEM ]...
Page 57
TRACTOR - - MODEL NUMBER 917,273661 KOHLER ENGINE-MODEL NUMBERCV730 TYPE NUMBER 0028 CRANKSHAFT PART DESCRIPTION 24-014-42-S Crankshaft (includes 52-139-09-S Plug, cup EXHAUST PART DESCRIPTION 24-041-49-S Gasket, exhaust (2) 25-072-04-S Stud, M8x1.25x33 (4) PA-CV730-0018Replacement Engine 24 522 327 Short Block 24-782-23 Miniblock 24-755-113-S Gasket Set FUEL SYSTEM...
Page 59
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION _OLo ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. down the face of slopes, never across the face. Do not mow ARNING: To avoid serious injury, operate your tractor up and slopes greater than 15 degrees.
Page 60
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, iiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiii_ no matter who made it, no matter who sold it! iiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiii_ iiiiiiiiiiiiiiii_ For the replacement parts, accessories...