Oki C9800hdn Software Installation Manual
Oki C9800hdn Software Installation Manual

Oki C9800hdn Software Installation Manual

Software setup c9800 series
Hide thumbs Also See for C9800hdn:

Advertisement

C9800 Software Installation Guide

Table of Contents

Network Installation ..............................................2
Windows ..........................................................2
Install the Ferrite Core ....................................2
Novell...............................................................7
Windows® Installation ..........................................8
USB Connection ..............................................8
Parallel Connection........................................11
Macintosh® Installation ......................................13
OS 9.1 to 9.2.x ...............................................14
OS X.1+ to X.3+ ............................................16
Service and Support.............................................18
About this Guide
This guide describes the initial printer driver installation. For
more detailed information, refer to the EFI User Software
Installation Guide and EFI Configuration Guide provided on
the User Documentation CD (CD3).
The general steps for installing the software are as follows:
• Install the PostScript printer driver or PCL printer driver
and corresponding printer driver files.
• Set up the printer driver to communicate with the Fiery.
• Install Fiery utilities and user software.
Configure Fiery utilities and user software.
You must also configure either a local connection for printing
directly to your printer or a network connection for printing over
a network.
A full set of user documentation, where procedures are
described in detail, is provided on the User Documentation
CD (CD3).
1
NOTE

Advertisement

Table of Contents
loading

Summary of Contents for Oki C9800hdn

  • Page 1: Table Of Contents

    C9800 Software Installation Guide About this Guide Table of Contents This guide describes the initial printer driver installation. For more detailed information, refer to the EFI User Software Network Installation ..........2 Installation Guide and EFI Configuration Guide provided on the User Documentation CD (CD3). Windows ............2 Selecting a printer driver in Windows ....2 The general steps for installing the software are as follows:...
  • Page 2: Network Installation

    CAUTION! Do not connect this product to an uninterruptible power supply (UPS). For further information please contact Oki 3. Place the open core about 1 inch from the cable connector Data at 1-800-OKIDATA or www.okidata.com. on the printer end.
  • Page 3 Network Installation Windows (cont’d) 2 Connect the Ethernet Interface 3 Assign an IP address to the printer If you are not using DHCP, you need to obtain an IP Address from your network Administrator and enter it using the front panel: 1.
  • Page 4 Install Browse to your CD-ROM drive. Double-click manually load the LPR Utility from the Menu Installer on CD1. To do this, click Custom Install /Network Software/ Click InstallationConfig/OKI LPR. 2. Select your language. 5 Install Printer Utilities Next 3. Click to accept the License Agreement.
  • Page 5 5. Select Quick Install to install only Command WorkStation, or, 1. Click Start Settings Printers CUSTOM INSTALL select to install your choice of these OKI C9800 EFI Fiery icon EFI tools: 2. Right click the > Command WorkStation Properties. 3. Click > Fiery Mail Port 4. Click the Installable Options tab.
  • Page 6 Network Installation Windows (cont’d) 5. Select Two-Way Communications. 6. Type the Fiery IP address or DNS name. 7. To display the printer’s current default settings when opened, select Update Fiery Driver When Opened . Update 8. Click . Click 8 Install the User Documentation 1.
  • Page 7: Novell

    2 Install the Printer on a Novell ® Network This utility installs, configures, and manages Oki network print server devices. Novell Client for Windows must be loaded, the Admin Manager software must be running, and you must be logged in to NDS.
  • Page 8: Windows® Installation

    Windows Installation ® USB Connection 1 Connect the USB Cable 2 Install the Fiery PostScript Printer Driver NOTE The installation procedure may vary slightly depending on the operating system you are using. Drivers are provided for ® Windows XP, 2000, Me, and 98. 1.
  • Page 9 Windows Installation ® USB Connection (cont’d 9. Click . Then, close the Printers dialog box. NOTE To print a test page: If New Hardware Found Wizard displays: → → Start Settings Printers 10. Click Win 98: Select “Search for the best driver for your Next device”.
  • Page 10 Windows Installation ® USB Connection (cont’d) 5 Install the User Documentation 1. Insert the User Documentation CD (CD3) into your CD-ROM drive. The CD will autorun. Start → Run → Browse If it doesn’t autorun, click Browse to your CD-ROM drive. Double-click Install Click 2.
  • Page 11: Parallel Connection

    Windows Installation ® Parallel Connection 1 Connect the parallel Interface 2 Install the Fiery PostScript Printer Driver NOTE The installation procedure may vary slightly depending on the operating system you are using. Drivers are provided for ® Windows XP, 2000, Me, and NT 4.0. 1.
  • Page 12 Windows Installation ® Parallel Connection (cont’d) 5 Install the User Documentation 16. Right-click the printer icon. → → Properties General Tab Print Test 17. Click 1. Insert User Documentation CD (CD3) into your CD-ROM Page drive. The CD will autorun. Start →...
  • Page 13: Macintosh Installation

    Macintosh Installation ® Network Interface Connection USB Interface Connection IMPORTANT! • Requires Mac OS 9.04 or higher Before connecting the network cable, install the Ferrite Core. • Printer operation is not assured if another USB compatible See “1 Install the Ferrite Core” on page 2. device is connected concurrently with it.
  • Page 14: Install The Driver

    Package, PPD Files, Adobe PS Options Plug-ins, SDM for MAC, Swatch Utility, Admin Setup Utility, Printing 6. Highlight your OKI printer model, click Plug-ins. Create 7. Click . The OKI printer icon appears on the desktop. 8. Click AutoSetup Continue 11. Click to install additional utilities.
  • Page 15: User Documentation

    Installation ® OS 9.1 to 9.2.x (cont’d) 4 Install the EFI Fiery Utilities 1. Place EFI Utilities CD (CD2) in the CD-ROM drive. OKI CD 2. Double-click the icon that appears on the desktop. 3. Double-click the icon. User Software 4.
  • Page 16: Os X.1+ To X.3

    2. Place the CD supplied with the printer in the CD-ROM 2. Double-click the icon that appears on the desktop. drive. 3. Double-click the icon. 3. Double-click the OKI CD icon that appears on the desktop. User Software 4. Double-click MAC icon 4. Double-click 5. Double-click the...
  • Page 17 Macintosh Installation ® OS X.1+ to X.3+ (cont’d) 4 User Documentation For additional information on using printer features as well as printer utilities, see the on-line documentation. Requirements • Microsoft Internet Explorer version 4.0 or higher and Acrobat Reader. To Load In order to open the on-line documentation, you must have Acrobat Reader installed.
  • Page 18: Service And Support

    Service and Support If you need further assistance or have questions, see our web site: http://my.okidata.com In the U.S. and Canada, call: 1-800-OKI-DATA (1800-654-3282) 24 hours a day, 7 days a week...
  • Page 19 Trademarks OKI is a registered trademark of Oki Electric Industry Company, Ltd. Microsoft, Internet Explorer and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation.
  • Page 20 Oki Data Americas, Inc., 2000 Bishops Gate Blvd., Mt. Laurel, NJ 08054-4620 Tel: 1-800-654-3282 (856) 235-2600 Fax: (856) 222-5320, www.okidata.com © 2005 Oki Data Americas, Inc. 59373601...

This manual is also suitable for:

C9800hn

Table of Contents