Network Setup Troubleshooting Other Troubleshooting Tips P.10 This manual describes problems that may be encountered when setting up a network and their possible causes and solutions. Find a description related to your problem and follow the solution. Forgotten or Do Not Know the Access Point Name/Network Name (SSID), Security P.10 For problems not described here or which occur after setup, refer to the on-screen manual: Basic Guide/ Protocol (encryption standard), and Network Key...
Problems during Network Setup Easy setup Advanced setup Check 4 Is "WPA/WPA2 Enterprise" set as a security protocol (encryption standard) on the The Target Access Point is Not Displayed (Detected) access point? Check "WPA/WPA2 Enterprise" is not supported on the machine. Change the security protocol (encryption standard) for the access point, then configure settings again.
Access point was not detected. is Displayed Check 2 Check Make sure that the DHCP function of the access point is active. The message appears when no access point is found. • For details on how to check the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer.
Multiple access points with the same name exist. is Displayed Check 5 Is TKIP set as an encryption standard when the access point is configured to communicate using IEEE802.11n standard only? Check The message appears when multiple access points with the same name are found.
The directly entered access point was not detected. is Displayed Check 4 Is the MAC address filtering enabled on the access point? Check • For details on how to check the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer.
Glossary Glossary • SSID • IP address An identifier to identify the specific access point. Also called an access point name or a network name. A numerical identification assigned to each computer or network device connected to a network. • MAC address •...
Problems during Software Installation The Machine is Not Displayed (Detected) • When using an access point that does not support WPS, configure settings manually. For the procedure to configure settings of the machine manually, refer to "Wireless Setup Using Easy Check Setup"...
Glossary Check 3 • IP address Is the IP filtering feature enabled on the network device (router, access point, etc.)? A numerical identification assigned to each computer or network device connected to a network. • For details on how to check settings of the network device, refer to the manual supplied with the •...
Page 10
Check 2 Check 4 Is the machine connected to a network? When obtaining an IP address automatically, make sure that the DHCP function of the network device (router, access point, etc.) is active. • To confirm the connection status, press the Setup button, then using the { } [ ] and OK buttons, select Device settings >...
Other Troubleshooting Tips Reference Information Forgotten or Do Not Know the Access Point Name/Network Name Character Entry (SSID), Security Protocol (encryption standard), and Network Key Action Check This machine allows you to enter characters when an on-screen keyboard is displayed. Follow the procedure below.
Use the { or } button to select Other setup, then press the OK button. • To insert a space, select Space on the on-screen keyboard and press the OK button. • To insert characters, select the section (C) of the screen using the { or } button, move the cursor to the character on the right of the target position using the [ or ] button, then enter characters.
Page 13
Enter the access point name/network name (SSID), • When the access point is set to operate in IEEE802.11n and IEEE802.11g with TKIP set then press the left FUNCTION button. as an encryption standard, communication is established using IEEE802.11g. For details on how to enter characters, refer to "Character 11-A Entry"...
11-B WPA/WPA2 Specifying the Machine's IP Address (IPv4 only) Disable Press the OK button. Action The machine's IP Address can be specified by the following procedure. Press the Setup button. Select Device settings, then press the OK button. Enter the network key, then press the left FUNCTION button.
Restoring the Machine's Default LAN Settings to Perform Setup Again Action Follow the procedure below to restore LAN settings of the machine to the default state. Press the Setup button. Select Device settings, then press the OK button. Select LAN settings, then press the OK button. Select Reset LAN settings, then press the OK button.
Connection Checklist Check Check 1 Before connecting the machine, are the computer and network device (router, access point, etc.) configured and can the computer connect to the network? Configure the computer and network device. • For the procedures, refer to the manuals supplied with the computer and network device, or contact their manufacturers. Check 2 Are the machine and network device (router, access point, etc.) turned on? Turn on each device.
Page 17
Is the firewall function of your security software active? A message may appear on the computer monitor warning that Canon software is attempting to access the network. If the warning message appears, set the security software to always allow access.
Page 18
Solución de problemas de configuración de red Otros consejos para la solución de problemas P.10 Este manual describe los problemas que pueden aparecer al configurar una red y sus posibles causas y soluciones. Localice la descripción que se ajuste al problema y siga las instrucciones de la solución. Se ha olvidado o se desconoce el nombre del punto de acceso/nombre de red (SSID), el P.10 Si el problema no está...
Problemas durante la configuración de red Configuración fácil Configuración avanzada Comprobación 4 ¿En el punto de acceso está establecido “WPA/WPA2 Empresa” como protocolo de No se muestra (detecta) el punto de acceso de destino seguridad (estándar de codificación)? Comprobaciones El equipo no admite “WPA/WPA2 Empresa”. Cambie el protocolo de seguridad (estándar de codificación) del punto de acceso y vuelva a establecer la configuración.
Se muestra Punto de acceso no detectado. (Access point was not Comprobación 2 detected.) Compruebe que la función DHCP del punto de acceso está activada. Comprobaciones • Para obtener información sobre cómo comprobar la configuración del punto de acceso, consulte el manual suministrado con éste o póngase en contacto con el fabricante.
Se muestra Existen varios puntos de acceso con el mismo nombre. Comprobación 5 (Multiple access points with the same name exist.) ¿Se ha establecido TKIP como estándar de encriptación al configurar el punto de acceso para que se comunique exclusivamente con el estándar IEEE802.11n? Comprobaciones Este mensaje aparece cuando se localizan varios puntos de acceso con el mismo nombre.
Se muestra No se ha detectado el punto de acceso introducido Comprobación 4 directamente. (The directly entered access point was not ¿Está activado el filtrado de direcciones MAC en el punto de acceso? detected.) • Para obtener información sobre cómo comprobar la configuración del punto de acceso, consulte el manual suministrado con éste o póngase en contacto con el fabricante.
Glosario Glosario • SSID • Dirección IP Identificador de un punto de acceso específico. También se denomina nombre del punto de acceso o Identificación numérica asignada a cada ordenador o dispositivo de red conectado a una red. nombre de red. •...
Problemas durante la instalación del software El equipo no aparece (no se detecta) • Cuando utilice un punto de acceso que no admita WPS, establezca la configuración manualmente. Para conocer el procedimiento para establecer la configuración del equipo Comprobaciones manualmente, consulte “Configuración inalámbrica mediante Configuración fácil (Easy Setup)” en el manual impreso: Guía de inicio.
Glosario Comprobación 3 • Dirección IP ¿Está activada la función de filtrado IP en el dispositivo de red (router, punto de Identificación numérica asignada a cada ordenador o dispositivo de red conectado a una red. acceso, etc.)? • Para obtener información sobre cómo comprobar la configuración del dispositivo de red, consulte •...
Comprobación 2 Comprobación 4 ¿El equipo está conectado a una red? Cuando obtenga la dirección IP automáticamente, asegúrese de que la función DHCP del dispositivo de red (router, punto de acceso, etc.) está activada. • Para confirmar el estado de conexión, pulse el botón Configuración (Setup) y, a continuación, mediante los botones { } [ ] y OK, seleccione Configuración de dispositivo (Device settings) >...
Otros consejos para la solución de problemas Información de referencia Se ha olvidado o se desconoce el nombre del punto de acceso/nombre Introducción de caracteres de red (SSID), el protocolo de seguridad (estándar de cifrado) y la Acción clave de red Comprobaciones Este equipo permite introducir caracteres cuando se muestra un teclado en pantalla.
Utilice el botón { o } para seleccionar Otra configuración (Other setup) y, a continuación, pulse • Para introducir un espacio, seleccione Espacio (Space) en el teclado en pantalla y pulse el botón OK. el botón OK. • Para introducir caracteres, seleccione la sección (C) de la pantalla utilizando el botón { o }, mueva el cursor al carácter situado a la derecha de la posición de destino mediante el botón [ o ] y, a continuación, introduzca los caracteres.
Page 29
Introduzca el nombre del punto de acceso/nombre de • Cuando se establece el punto de acceso para que opere en IEEE802.11n y IEEE802.11g red (SSID) y, a continuación, pulse el botón FUNCIÓN con TKIP como estándar de encriptación, la comunicación se establece utilizando (FUNCTION) izquierdo.
11-B WPA/WPA2 Especificación de la dirección IP del equipo (sólo IPv4) Desactivado Pulse el botón OK. Acción La dirección IP del equipo se puede establecer con el procedimiento siguiente. Pulse el botón Configuración (Setup). Seleccione Configuración de dispositivo (Device settings) y, a continuación, Introduzca la clave de red y, a continuación, pulse el botón OK.
Restauración de la configuración de LAN predeterminada del equipo para volver a configurar Acción Siga el procedimiento que se indica a continuación para restaurar la configuración de LAN del equipo al estado predeterminado. Pulse el botón Configuración (Setup). Seleccione Configuración de dispositivo (Device settings) y, a continuación, pulse el botón OK.
Lista de comprobación de las conexiones Comprobaciones Comprobación 1 Antes de conectar el equipo, ¿se han configurado el ordenador y el dispositivo de red (router, punto de acceso, etc.) y el ordenador se puede conectar a la red? Configure el ordenador y el dispositivo de red. •...
Page 33
¿Está activada la función de firewall del software de seguridad? En la pantalla del ordenador puede aparecer un mensaje advirtiendo de que el software de Canon está intentando acceder a la red. Si aparece el mensaje de advertencia, establezca en el software de seguridad que permita el acceso siempre.