External Control Device Setup - LG RU-42PX10 Owner's Manual

External Control Device Setup
Use this function to specify a monitor JD number,
Refer to 'Rea_ Data Mapping 1' See page 35,
1. Press the MENU button and then use &/V button to select the SPECL&L menu.
2. Press the Ip button and then use &/T button to select _,
3 Press the _ butch and then use _ z I_ button to adiust Set _B to ch_se the
desired monitor _D number. The adjustment range of Set m is 1 ~ 99
4, Press the ENTER button to save,
. Baud rate :9600 bps (UART)
* Data mength : 8 bi_
o Parity : None
* Use a crossed (reverse) cable,
• Stop bit : 1 bit
• Communication cede : ASCH code
COMMAND 1 COMMAND 2
01, Power
02, input _
03 Aspect Ratio
04. Screen Mute
05. VoJu_ Mute
06. Vdurr, e _ntrot
07. Contrast
QS. B[_htness
09. CoJor
10 Tvnt
11, Sharpness
12, OSD Se_:_-t
13 Remote Contro_ Lock M_
14 PtP/DW
!5, SP__om
16 PiP Pos_
17. Tre_e
18. Ms
19. BaJ_ce
20. Color Tem_rature
21. Red Adju_nt
22 Green Adju_
23, Blue Adjustment
24. PIP _nput Source
25, Abnorm_ State
26, _SM Method
27, Low Po_r
28. Orbiter _rr_ Se_
29. Orbiter P{xel _tflng
30. Picture Si_
31. Auto Config
COM
_Transr_Jssie_
l[Commandl][Comman_][ ][Set ID][ ][Datal[Cr] 1
[Command 1]: First command to contro_ PDP set. (j, k or m)
* [Command 2]: Second command to control PDP set.
[Set }D]: You can adjust the set ID to choose desired monitor
JD number in Speciam menu. Adjustment range is 1
99. When selecting Set ID '0', every connected
PDP set is cor_roHed, Set _D is indicated as deci-
mal (1 ~99) on menu and as Hexa decimal
(OxO-Ox63) on transmission/receiving protocol
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCH code 'OxOD'
* [ ]: ASCH _e 'space (Ox20)'
OK Acknowle_
[[Command2][ ][Set ID][ ][OKl[Da_][x] ]
The Monitor transmits ACK (acknowledgement) based on
this format when receiving norma_ data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
I[Commane2][
][Set iDl[ ][NG][Data][x] I
* The Monitor transmi_ ACK (acknowledgement} based on
this format when receiving abnorma_ data from nomviabte
functions or communication errors.
Data 1: IrlegaJ Code
2: Not supported functien
3: Wait more time
DATA
(Hexa_cimal}
k a 0~1
k b 0-_6
k c 0_3
k d 0--1
k e 0~1
k f 0_
k _ 0_
k h 0~64
k i 0 _- 64
k i 0--64
k k 0 ~ 64
k I 0~1
k m 0~1
k n 0~3
k R 0 ~99
k q 0~3
k r 0~_
k s 0--64
k t 0~_
k u 0--3
k v O_ 3C
k w 0 _ 3C
k $ 0 ~ 3C
k y 0~6
k z O~a
i p 0_3
j r 1 ~ FE
j s _g
j t 0 ~14
j u 1
OOM DATA 0 DATA 1 DATA2 DATA 3
MAND 1 MAND2
{Nexad_ma_}(N_;,xa_em_{kiex_de_mal)(Hex_e_m_i)
32, Tune _mmand
m a
01 *- 7D 0 0 rrain_b!Tu_nd
3& Channel Add/Del m b 0 ~ 1
34, Key m c Key code
34 Plasma TV