Epson PowerLite S11 User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Projector
  5. PowerLite S11
  6. User manual

Epson PowerLite S11 User Manual

Epson projector user manual
Hide thumbs Also See for PowerLite S11:
Table of Contents

Advertisement

Quick Links

®
PowerLite
S11/X12/X15 User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Epson PowerLite S11

Summary of Contents for Epson PowerLite S11

  • Page 1 ® PowerLite S11/X12/X15 User's Guide...

  • Page 3: Table Of Contents

    Projector Part Locations ... 14 Projector Parts - Front/Top ... 15 Projector Parts - Rear ... 16 Projector Parts - Base... 19 Projector Parts - Control Panel ... 20 Projector Parts - Remote Control... 22 Setting Up the Projector ... 24 Projector Placement... 24 Projector Setup and Installation Options ...
  • Page 4 Connecting to External Speakers ... 38 Connecting to External USB Devices ... 39 USB Device Projection... 40 Connecting a USB Device or Camera to the Projector... 40 Selecting the Connected USB Source ... 41 Disconnecting a USB Device or Camera From the Projector... 41 Connecting to a Document Camera ...
  • Page 5 Password Security Types ... 74 Setting a Password ... 74 Selecting Password Security Types... 76 Entering a Password to Use the Projector ... 76 Saving a User's Logo Image to Display... 78 Locking the Projector's Buttons ... 79 Unlocking the Projector's Buttons ... 80 Installing a Security Cable ...
  • Page 6 Solutions When the Image Brightness or Colors are Incorrect ... 118 Solutions When There is No Sound or Low Volume ... 119 Solving Projector or Remote Control Operation Problems ... 119 Solutions to Projector Power or Shut-Off Problems... 120 Solutions to Problems with the Remote Control ... 120 Solutions to Password Problems ...
  • Page 7 Remote Control Specifications ... 126 Projector Dimension Specifications... 126 Projector Electrical Specifications ... 126 Projector Environmental Specifications... 127 Projector Safety and Approvals Specifications... 127 Supported Video Display Formats... 128 USB Display System Requirements ... 130 Notices ... 132 Recycling... 132 Important Safety Information ...

  • Page 9: Introduction To Your Projector

    The PowerLite S11, X12, and X15 projectors include these special features: Bright, high-resolution projection system • PowerLite S11: Up to 2600 lumens of brightness (white light output and color light output) PowerLite X12: Up to 2800 lumens of brightness (white light output and color light output) PowerLite X15: Up to 3000 lumens of brightness (white light output and color light output) •...

  • Page 10: Product Box Contents

    Introduction to Your Projector Related concepts Projector Part Locations Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping. Make sure your projector box included all of these parts:...

  • Page 11: Additional Components

    Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the HDMI port.

  • Page 12: Optional Equipment And Replacement Parts

    Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an EPSON authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com Epson offers the following optional accessories and replacement parts for your projector:...

  • Page 13: Warranty And Registration Information

    In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.

  • Page 14: Projector Part Locations

    • If you still need help after checking this manual and the sources listed above, you can use the EPSON PrivateLine Support service to get help fast. For details, see "Where to Get Help". Parent topic: Introduction to Your Projector...

  • Page 15: Projector Parts - Front/Top

    Projector Parts - Front/Top Exhaust vent Lamp cover Horizontal keystone slider (PowerLite X12/X15) Control panel Projector status lights Focus ring (PowerLite S11) Speaker Air filter cover Intake vent Zoom ring (PowerLite X12/X15)

  • Page 16: Projector Parts - Rear

    A/V Mute slide Front adjustable foot Foot release lever A/V Mute slide lever Parent topic: Projector Part Locations Projector Parts - Rear PowerLite S11 Remote control receiver Audio ports S-Video port USB TypeA/document camera port USB TypeB port Computer port...
  • Page 17 Audio Out port Monitor Out port Lamp cover screw Security lock port Video port AC input port PowerLite X12 Remote control receiver Audio ports S-Video port USB TypeA/document camera port USB TypeB port Computer port RS-232C serial port HDMI port Lamp cover screw...
  • Page 18 Security lock port Video port AC input port PowerLite X15 Remote control receiver S-Video port Audio Out port USB TypeB port Computer1 port Computer2 port HDMI port Lamp cover screw Security lock port RS-232C serial port Audio port AC input port...

  • Page 19: Projector Parts - Base

    Video port Parent topic: Projector Part Locations Projector Parts - Base Mounting bracket holes Front adjustable foot Rear feet Security cable attachment point...

  • Page 20: Projector Parts - Control Panel

    Parent topic: Projector Part Locations Projector Parts - Control Panel PowerLite S11 Power button Source Search button (searches for connected sources) Menu button (accesses projector menu system) Enter button (selects options) Wide/Tele buttons (adjusts projected image size), horizontal keystone adjustment buttons (adjust...
  • Page 21 Power button Source Search button (searches for connected sources) Menu button (accesses projector menu system) Enter button (selects options) Volume control buttons, horizontal keystone adjustment buttons (adjust screen shape), and arrow buttons Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons...

  • Page 22: Projector Parts - Remote Control

    Projector Parts - Remote Control Power button...
  • Page 23 Aspect button (selects the image aspect ratio) Num button (when held down, switches numeric buttons to number function) Menu button (accesses projector menu system) Arrow buttons (move through on-screen options and control wireless mouse functions) Enter button (selects options and controls wireless mouse functions)

  • Page 24: Setting Up The Projector

    • Place the projector on a sturdy, level surface or install it using a compatible mount. • Leave plenty of space around and under the projector for ventilation, and do not place it on top of or next to anything that could block the vents.
  • Page 25 Front Ceiling Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.

  • Page 26: Projection Distance

    The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings.

  • Page 27: Projector Connections

    • If your presentation or video includes sound, you can connect audio input cables, if necessary. • For slide shows without a computer (PowerLite S11/X12), you can connect USB devices (such as a flash drive or camera) or an optional EPSON document camera.

  • Page 28: Connecting To Computer Sources

    Connecting to a Computer for USB Video and Audio If your computer meets the system requirements, you can send video and audio output to the projector through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a USB cable.

  • Page 29: Connecting To A Computer For Vga Video

    Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port. Contact Apple for compatible adapter options.

  • Page 30: Connecting To A Computer For Hdmi Video And Audio

    Connecting to Computer Sources Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable (PowerLite X12/X15). Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.

  • Page 31: Connecting To A Computer For Usb Mouse Control

    If you connected your computer to a Computer, USB TypeB, or HDMI (PowerLite X12/X15) port on the projector, you can set up the remote control to act as a wireless mouse. This lets you control computer presentations at a distance from your computer. To do this, connect the projector to your computer using a USB cable, if it is not connected already.

  • Page 32: Connecting To A Computer For Sound

    TypeB or HDMI (PowerLite X12/X15) port, you can still play sound through the projector's speaker system. Just connect an optional stereo mini-jack adapter cable (with one 3.5 mm mini-plug and two RCA plugs) (PowerLite S11/X12). For the PowerLite X15, connect an optional 3.5 mm stereo mini-jack audio cable.

  • Page 33: Connecting To Video Sources

    Parent topic: Projector Connections Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable (PowerLite X12/X15). The HDMI connection provides the best image quality.

  • Page 34: Connecting To A Component-To-Vga Video Source

    Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using a component- to-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable.

  • Page 35: Connecting To A Composite Video Source

    Input Signal Settings - Signal Menu Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1. Connect the cable with the yellow connector to your video source's yellow video output port.

  • Page 36: Connecting To An S-Video Video Source

    Connecting to Video Sources Connecting to an S-Video Video Source If your video source has an S-Video port, you can connect it to the projector using an optional S-Video cable. 1. Connect the S-Video cable to your video source's S-Video output port.

  • Page 37: Connecting To A Video Source For Sound

    You can play sound through the projector's speaker system if your video source has audio output ports. Connect the projector to the video source using an RCA audio cable (PowerLite S11/X12) or an optional stereo mini-jack audio cable (PowerLite X15).

  • Page 38: Connecting To An External Computer Monitor

    If you connected the projector to a computer using a Computer port, you can also connect an external monitor to the projector (PowerLite S11). This lets you see your presentation on the external monitor even when the projected image is not visible.

  • Page 39: Connecting To External Usb Devices

    Note: The projector's built-in speaker system is disabled when you connect external speakers. 1. Make sure your computer or video source is connected to the projector with both audio and video cables as necessary. 2. Locate the appropriate cable to connect your external speakers, such as a stereo mini-jack-to-pin- jack cable, or another type of cable or adapter.

  • Page 40: Usb Device Projection

    Projecting a Slide Show Connecting a USB Device or Camera to the Projector You can connect your USB device or camera to the projector's USB TypeA port and use it to project images and other content (PowerLite S11/X12). 1. If your USB device came with a power adapter, plug the device into an electrical outlet.

  • Page 41: Selecting The Connected Usb Source

    2. Connect the USB cable (or USB flash drive or USB memory card reader) into the projector's USB TypeA port shown here. Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not operate correctly.

  • Page 42: Connecting To A Document Camera

    Connecting to a Document Camera You can connect the EPSON DC-06 document camera to your projector's USB TypeA port to project images viewed by the camera (PowerLite S11/X12). Note: For additional features supported by software, connect the EPSON DC-06 document camera to your computer instead of the projector.
  • Page 43 1. Open the battery cover as shown. 2. Insert the batteries with the + and – ends facing as shown.

  • Page 44: Opening The Lens Cover

    Setting Up the Projector Opening the Lens Cover 1. To open the projector's lens cover, slide the A/V Mute slide lever. 2. To cover the lens or temporarily turn off the projected picture and sound, slide the A/V Mute slide cover closed.

  • Page 45: Using Basic Projector Features

    Controlling the Volume with the Volume Buttons Projecting a Slide Show Turning On the Projector Turn on the computer or video equipment you want to use before you turn on the projector so it can display the image source. 1. Open the projector's lens cover.
  • Page 46 The projector beeps and the power light flashes green as the projector warms up. After about five seconds, the power light stops flashing and turns green. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children.

  • Page 47: Turning Off The Projector

    2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the power light turns orange. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary).
  • Page 48 3. To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange.

  • Page 49: Selecting The Language For The Projector Menus

    Parent topic: Using Basic Projector Features Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
  • Page 50 2. To adjust the front foot, pull up on the foot release lever and lift the front of the projector. The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height.

  • Page 51: Image Shape

    You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
  • Page 52 3. Press a keystone button on the projector's control panel to adjust the image shape. Note: The horizontal keystone adjustment buttons are labeled Wide and Tele on the PowerLite S11. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape using the Keystone settings in the projector menus.

  • Page 53: Correcting Image Shape With The Horizontal Keystone Slider

    Projector Feature Settings - Settings Menu Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides. 1. Turn on the projector and display an image.
  • Page 54 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen. 6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter.

  • Page 55: Resizing The Image

    Image Shape Resizing the Image You can resize the image using the projector's zoom ring or the Wide and Tele buttons, depending on the projector model. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.

  • Page 56: Focusing The Image Using The Focus Ring

    Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles...

  • Page 57: Using The Remote Control As A Wireless Mouse

    ± 15º Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.

  • Page 58: Using The Remote Control As A Presentation Pointer

    Using the Remote Control as a Presentation Pointer You can use the projector's remote control as a pointer to help you call out important information during a presentation. The default pointer shape is an arrow, but you can select an alternative shape using the Settings menu.

  • Page 59: Selecting An Image Source

    Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1. Make sure the connected image source you want to use is turned on.
  • Page 60 • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources. Computer port sources Video and HDMI (PowerLite X12/X15) sources USB port sources (computer display and external devices; PowerLite S11/X12) Parent topic: Using Basic Projector Features...

  • Page 61: Projection Modes

    Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.

  • Page 62: Changing The Projection Mode Using The Menus

    Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.

  • Page 63: Changing The Image Aspect Ratio

    Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control.

  • Page 64: Color Mode

    Image Quality Settings - Image Menu Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use.

  • Page 65: Available Color Modes

    4. To cycle through all the available Color Modes for your input signal, press the Color Mode button repeatedly. Parent topic: Color Mode Available Color Modes You can set the projector to use these Color Modes, depending on the input source you are using: Color Mode Presentation Dynamic Theatre...

  • Page 66: Turning On Auto Iris

    You can use the Volume buttons on the remote control to adjust the volume as you project a presentation with audio. You can also use the volume buttons on the projector's control panel (PowerLite X12/X15). The volume buttons control the projector’s internal speaker system.

  • Page 67: Projecting A Slide Show

    2. Press the Volume buttons as necessary to lower or raise the volume. A volume gauge appears on the screen. 3. To set the volume to a specific level for an input source, you can set the volume using the projector's menus.

  • Page 68: Starting A Slide Show

    Projecting a Slide Show Starting a Slide Show After connecting a USB device to the projector (PowerLite S11/X12), you can switch to the USB input source and start your slide show. Note: You can change the Slideshow operation options or add special effects by highlighting Option at the bottom of the screen and pressing Enter.
  • Page 69 2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. •...

  • Page 70: Slideshow Display Options

    Related tasks Disconnecting a USB Device or Camera From the Projector Slideshow Display Options You can select these display options when using the projector's Slideshow feature. Setting Display Order Sort Order Continuous Play Screen Switching Time Options Description Name Order...
  • Page 71 Setting Options Effect Wipe Dissolve Random Parent topic: Starting a Slide Show Description Transitions between images with a wipe effect Transitions between images with a dissolve effect Transitions between images using a random variety of effects...

  • Page 72: Adjusting Projector Features

    1. Press the A/V Mute button on the remote control to temporarily stop projection and mute any sound. 2. To turn the picture and sound back on, press A/V Mute again. Note: You can also stop projection using the A/V Mute slide lever on the projector. Parent topic:...

  • Page 73: Stopping Video Action Temporarily

    2. To restart the video action in progress, press Freeze again. Parent topic: Adjusting Projector Features Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen.

  • Page 74: Projector Security Features

    Adjusting Projector Features Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings.
  • Page 75 1. Hold down the Freeze button on the remote control until you see the Password Protect menu. This takes about five seconds. 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 3.

  • Page 76: Selecting Password Security Types

    If you do not see this menu, hold down the Freeze button on the remote control for five seconds until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protect, press Enter, select On, and press Esc.
  • Page 77 • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact EPSON Support. When you contact EPSON Support, provide the displayed request code and proof of ownership for assistance in unlocking the projector.

  • Page 78: Saving A User's Logo Image To Display

    Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature).

  • Page 79: Locking The Projector's Buttons

    You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished.

  • Page 80: Unlocking The Projector's Buttons

    Unlocking the Projector's Buttons Parent topic: Projector Security Features Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them. Parent topic: Locking the Projector's Buttons Installing a Security Cable You can install two types of security cables on the projector to deter theft.
  • Page 81 • Use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.

  • Page 82: Adjusting The Menu Settings

    Projector Reset Options - Reset Menu Using the Projector's Menus You can use the projector's menus to adjust the settings that control how your projector works. The projector displays the menus on the screen. 1. Press the Menu button on the control panel or remote control.

  • Page 83: Image Quality Settings - Image Menu

    2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4.
  • Page 84 To change settings for an input source, make sure the source is connected and select that source. Setting Options Color Mode See the list of available Color Modes Brightness Varying levels available Contrast Varying levels available Color Saturation Varying levels available Tint Varying levels available Sharpness...

  • Page 85: Input Signal Settings - Signal Menu

    Available Color Modes Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
  • Page 86 Auto Setup Resolution Auto Normal Wide Tracking Varying levels available Sync. Varying levels available Position Up, down, left, right Progressive PowerLite S11: PowerLite X12/X15: Video Film/Auto Noise Reduction (PowerLite X12/X15) HDMI Video Range Normal (PowerLite X12/X15) Expanded Auto Description Automatically optimizes...

  • Page 87: Projector Feature Settings - Settings Menu

    Parent topic: Adjusting the Menu Settings Related references Available Image Aspect Ratios Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. Options Description Auto Specifies the signal type from input sources connected to...
  • Page 88 Setting Options Keystone H/V Keystone Quick Corner Zoom Varying levels available (PowerLite S11) Control Panel Lock Full Lock Partial Lock Pointer Shape Three shapes available Description Adjusts image shape to rectangular (horizontally and vertically) H/V Keystone: lets you manually correct horizontal and vertical...
  • Page 89 ECO: reduces lamp brightness and fan noise, and saves power and lamp life Adjusts the volume of the projector’s speaker system or external speakers (PowerLite S11) Limits reception of remote control signals by the selected receiver; Off turns off all receivers...

  • Page 90: Projector Setup Settings - Extended Menu

    Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Display Options Description Messages Selects various display options Display Background Messages: controls whether messages are displayed on the...
  • Page 91 Selects various operation options Direct Power On: turns on the projector when you plug it in Sleep Mode: automatically turns off the projector after an interval of inactivity Sleep Mode Timer: sets the...

  • Page 92: Projector Information Display - Info Menu

    Language Parent topic: Adjusting the Menu Settings Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Options Description Communication On...
  • Page 93 Lamp Hours Displays the number of hours (H) the lamp has been used in Normal and ECO Power Consumption modes; if the information is displayed in yellow, obtain a genuine Epson replacement lamp soon Source Displays the name of the port to which the current input source is...

  • Page 94: Projector Reset Options - Reset Menu

    Projector Lamp Specifications Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All option on the Reset menu. You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset Lamp Hours option.

  • Page 95: Maintaining And Transporting The Projector

    Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation. The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part needs replacing, contact Epson or an authorized EPSON servicer.

  • Page 96: Cleaning The Projector Case

    Projector Maintenance Cleaning the Air Filter and Vents Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them. 1. Turn off the projector and unplug the power cord.

  • Page 97: Replacing The Air Filter

    • After cleaning the air filter, you see a message telling you to clean or replace it • The air filter is torn or damaged You can replace the air filter while the projector is mounted to the ceiling, if necessary. The illustrations here show the projector placed on a table.
  • Page 98 2. Carefully open the air filter cover. 3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.

  • Page 99: Projector Lamp Maintenance

    4. Place the new air filter in the projector as shown and push gently until it clicks into place. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.

  • Page 100: Replacing The Lamp

    Projector Information Display - Info Menu Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury.
  • Page 101 4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
  • Page 102 6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
  • Page 103 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down until it locks into place. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
  • Page 104 8. Push in the lamp firmly and tighten the screws to secure it. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on.

  • Page 105: Resetting The Lamp Timer

    Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information.

  • Page 106: Replacing The Remote Control Batteries

    Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
  • Page 107 Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Operation...

  • Page 108: Transporting The Projector

    • Use a carrying case to hand-carry the projector. • When transporting the projector a long distance or as checked luggage, place it in a carrying case. Then pack the case in a firm box with cushioning around it and mark the box "Fragile."...

  • Page 109: Solving Problems

    Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it If this does not solve the problem, check the following: • The lights on the projector may indicate what the problem is.
  • Page 110 Green Flashing green Orange Flashing orange Off Status and solution Normal operation. Warming up. Wait for an image to appear. Standby or sleep mode. Preparing for monitoring or shutting down. (When the light remains orange, you can unplug the projector.)
  • Page 111 • If the problem persists, unplug the projector and contact Epson for help. Replace the lamp soon to avoid damage. Do not continue using the projector. A fan or sensor has a problem. Turn the projector off, unplug it, and contact Epson for help.

  • Page 112: Using The Projector Help Displays

    Power light Lamp light Red or flashing Flashing red Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help. Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu...

  • Page 113: Solutions When No Image Appears

    • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources. • Press the projector's power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver.

  • Page 114: Solutions When Image Is Incorrect Using The Usb Display Function

    • If the mouse cursor flickers, select Make the movement of the mouse pointer smooth in the EPSON USB Display Settings program on your computer. • Turn off the Transfer layered window setting in the EPSON USB Display Settings program on your computer.

  • Page 115: Displaying From A Pc Laptop

    2. To display on both the laptop's monitor and the projector, try pressing the same keys again. 3. If the same image is not displayed by the laptop and projector, check the Windows Display utility to make sure the external monitor port is enabled. (See your computer or Windows manual for instructions.)

  • Page 116: Solutions When Only A Partial Image Appears

    If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible. • If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape.

  • Page 117: Solutions When The Image Contains Noise Or Static

    • Securely connected at both ends • Not connected to an extension cable • Check the settings on the projector's Signal menu to make sure they match the video source. If available for your video source, adjust the Progressive and Noise Reduction settings.

  • Page 118: Solutions When The Image Is Fuzzy Or Blurry

    • Adjust the image focus. • Clean the projector lens. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen.

  • Page 119: Solutions When There Is No Sound Or Low Volume

    • Make sure any connected audio cables are labeled "No Resistance". • If you are using the USB Display function, turn on the Output audio from the projector setting in the EPSON USB Display Settings program on your computer.

  • Page 120: Solutions To Projector Power Or Shut-Off Problems

    Solving Problems Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet.

  • Page 121: Solutions To Password Problems

    • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson. • If you lose the remote control you cannot enter a password. Order a new one from Epson. Parent topic:...
  • Page 122 Speak to a Support Representative To use the EPSON PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

  • Page 123: Technical Specifications

    Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats USB Display System Requirements...
  • Page 124 Brightness PowerLite S11: Normal Power Consumption mode: White light output 2600 lumens (ISO 21118 standard) Color light output 2600 lumens ECO Power Consumption mode: White light output 2080 lumens (ISO 21118 standard) PowerLite X12: Normal Power Consumption mode: White light output 2800 lumens (ISO 21118 standard)

  • Page 125: Projector Lamp Specifications

    Noise level Keystone correction angle USB Type B port compatibility USB 1.1 and 2.0 compliant for USB display or external mouse USB Type A port compatibility USB 1.1 and 2.0 compliant for USB device input or EPSON (PowerLite S11/X12) Parent topic:...

  • Page 126: Remote Control Specifications

    Lamp life Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Remote Control Specifications...

  • Page 127: Projector Environmental Specifications

    Projector Environmental Specifications Temperature Humidity (relative, non-condensing) Operating altitude Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States Canada Operating: Normal Power Consumption mode: 283 W ECO Power Consumption mode: 234 W Standby: 0.36 W (Communication Off), 2.9 W (Communication On)

  • Page 128: Supported Video Display Formats

    For best results, your computer monitor or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.
  • Page 129 Display format Refresh rate (in Hz) MAC16" MAC19" MAC21" Composite video TV (NTSC) TV (PAL) 50/60 TV (SECAM) Component video SDTV (480i) SDTV (576i) SDTV (480p) SDTV (576p) HDTV (720p) 50/60 HDTV (1080i) 50/60 HDMI input signals (PowerLite X12/X15) SVGA WXGA SXGA SXGA+...

  • Page 130: Usb Display System Requirements

    HDTV (1080i) HDTV (1080p) * Wide resolution only (PowerLite X12/X15) Parent topic: Technical Specifications USB Display System Requirements Your computer system must meet the system requirements here to use the projector's USB Display software. Requirement Operating system USB version Memory...
  • Page 131 Parent topic: Technical Specifications...

  • Page 132: Notices

    Caution: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.

  • Page 133: Important Safety Instructions

    • Do not look into the lens when the projector is on. The bright light can damage your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
  • Page 134 • Do not use the projector where it may be exposed to smoke, corrosive gases, or excessive dust. • Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle.

  • Page 135: Restriction Of Use

    • Do not disassemble the lamp or subject it to impacts. • Do not place the source of an open flame, such as a lit candle, on or near the projector. • Do not block the lens during projection using a book or any object other than the lens cover. This could damage the projector or cause a fire.

  • Page 136: Fcc Compliance Statement

    Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada. Parent topic: Notices Trademarks ® ® EPSON , Instant Off , PowerLite Your Vision is a registered logomark of Seiko Epson Corporation. ® ® , and Quick Corner are registered trademarks, and EPSON Exceed...

  • Page 137: Software Copyright

    We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the GPL Programs, contact Epson as described in the User's Guide.
  • Page 138 • udhcp 0.9.8 • uvc rev.219 • wireless_tools 29 • EPSON original drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright ©...
  • Page 139 we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.
  • Page 140 c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
  • Page 141 so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
  • Page 142 This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
  • Page 143 END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
  • Page 144 We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the LGPL Programs, contact Epson as described in the User's Guide.
  • Page 145 Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.
  • Page 146 When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
  • Page 147 and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".) "Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
  • Page 148 the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you;...
  • Page 149 If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6.
  • Page 150 to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system.
  • Page 151 If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims;...
  • Page 152 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A...
  • Page 153 That's all there is to it! BSD License (Berkeley Software Distribution License) This projector product includes the open source software program "University of California , Berkeley License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License".
  • Page 154 This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg". The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 155 (1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation. (2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent JPEG Group".
  • Page 156 This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng". The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 157 libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000 , are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors: Tom Lane Glenn Randers-Pehrson Willem van Schaik...
  • Page 158 September 12, 2004 zlib This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib". The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 159 If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes. mDNSResponder This projector product includes the open source software program "mDNSResponder" which applies the following license terms "Apache License Version 2.0, January 2004". List of "mDNSResponder"...
  • Page 160 "Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
  • Page 161 transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is...
  • Page 162 7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE.
  • Page 163 See the License for the specific language governing permissions and limitations under the License. newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib".
  • Page 164 * Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  • Page 165 WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. (4) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc. This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered.
  • Page 166 (8) Hewlett Packard (c) Copyright 1986 HEWLETT-PACKARD COMPANY To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
  • Page 167 OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (12) SuperH, Inc. Copyright 2002 SuperH, Inc. All rights reserved This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered.
  • Page 168 MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;...
  • Page 169 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  • Page 170 Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
  • Page 171 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
  • Page 172 IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE PRODUCT LICENSED HEREUNDER.
  • Page 173 WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;...
  • Page 174 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  • Page 175 All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 176 (35) - ARM Ltd (arm and thumb variant targets only) Copyright (c) 2009 ARM Ltd All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 177 MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL CODESOURCERY BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED...

  • Page 178: Copyright Notice

    Seiko Epson Corporation. The information contained herein is designed only for use with this EPSON product. Epson is not responsible for any use of this information as applied to other products.

  • Page 179: Copyright Attribution

    Copyright Attribution This information is subject to change without notice. © 2012 Epson America, Inc. 4/12 CPD-34721R2 Parent topic: Copyright Notice...

This manual is also suitable for:

Powerlite x12Powerlite x15

Table of Contents