Table of Contents
Advertisement
Other Features
Information On Screen
Programme Number, Programme Name (or AV) and
Sound Indicator are displayed on the upper right of the
screen. They are displayed after programme change for 3
seconds.
- -
C01
Programme Number and
Programme Name (5 characters)
,
,
Sound Indicator (Mono, Stereo, Dual)
The alternatives of Sound Indicator are Mono, Stereo, Dual
which shows the current sound mode.
Programme Number, Programme Name and Sound Indica-
tor OSD' s are displayed when a new programme is entered
by pressing digit or "- / - -" button, "
"-P/CH" button.
Sleep Timer Indicator (If activated)
Screen format Indicator
Sleep Timer and Screen format indicators are displayed with
Programme Number, Programme Name and Sound Indica-
tor by pressing "
" button.
TV
Sleep Timer Indicator shows the time left if enabled.
Sound Mute
To cut off the sound from the TV press " " button. To restore
the sound press the " " button again or use the "
" buttons, in this case the volume will start from minimum set-
ting.
Sound Modes
This is a stereo option. The alternatives of Sound Modes
are Mono, Stereo, Dual 1 and Dual 2. This indicator is dis-
played in the lower middle side of the screen. "I-II" button is
used to select Mono, Stereo, Dual 1 or Dual 2.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual 1 is selected in default and
also can be selected after Dual 2 by Remote Control.
If Dual 2 selected by Remote Control.
Screen Format
The Screen Format OSD is displayed below the sound indi-
cator, by TV satus OSD's. By pressing "
screen format can be switched into AUTO, 4:3 or 16:9.
AUTO
FORMAT
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid sig-
nal detected. It shows the remained time for the switching to
" button, "P/CH+" or
" button, the
4:3
16:9
FORMAT
FORMAT
the Stand-By mode (it will take 5 minutes). The indicator is
displayed in 3 seconds when there is no valid signal.
After a Remote Control command (if No-Signal Timer is ac-
tive) the timer stops and if no signal detected again the tim-
er is initialized to 5 minutes and starts 3 seconds later again
to count down.
Still Picture
Pressing "OK" button makes the picture on the screen fro-
zen. Pressing this button again enables moving pictures
again.
To Display the Time
• While watching a TV programme with Teletext transmis-
sion press "
tured from Teletext will be displayed at the upper right cor-
ner of the screen.
• If the programme being watched does not have Teletext
transmission, no time information will be displayed.
• The time information will disappear after pressing "
button again.
Flash back (
This button is used to return to the previous viewed preset.
By pressing the "
gle between two presets.
Double-digit (- / - -)
+" or "-
This OSD is displayed when the "- / - -" button pressed in
place of the programme number indicator.
After then, in order to enter a programme it must be pressed
to two digit consecutively. When it is late to press any digit
button this function will be ignored and the display will be
erased. In the same way it must not be late to press any dig-
it button after entering the first digit. The limit of the delay
time is 3 seconds.
AV Modes
By pressing the "
modes (except being in Teletext). Pressing this button will
switch the TV in one of the optional AV modes: EXT-1,
EXT-2, S-VHS EXT2. EXT.1 supports the RGB mode and
EXT.2 supports S-VHS EXT2 mode unless there is an
S-VHS socket..
In order to quit the AV mode press the "
"P/CH+" / "-P/CH" button.
ENGLISH - 14 -
NO SIGNAL
4 : 50 MIN
" button. The current time information, cap-
)
" button repeatedly it is possible to tog-
" button you can switch your TV to AV V
"
", digit buttons or
TV
Advertisement
Table of Contents
