Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.
Page 5
Model W1706 (Mfg. Since 3/13) Controls.and.Features Refer to Figures.1–2.and the descriptions below to better understand the controls and features of the Model W1706. A.. Blade.Quick-Release.Lever:.Quickly releases or engages blade tension for blade changes. B.. Blade.Tracking.Knob:.Adjusts and locks the blade tracking. C..
Model W1706 (Mfg. Since 3/13) SAFETY SAFETY For Your Own Safety, Read Manual Before Operating Machine The. purpose. of. safety. symbols. is. to. attract. your. attention. to. possible. hazardous. conditions.. This. manual.uses.a.series.of.symbols.and.signal.words.intended.to.convey.the.level.of.importance.of.the. safety.messages..The.progression.of.symbols.is.described.below..Remember.that.safety.messages.by. themselves. do. not. eliminate. danger. and. are. not. a. substitute. for. proper. accident. prevention. mea- sures—this.responsibility.is.ultimately.up.to.the.operator! Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,.
Page 7
INTENDED.USAGE..Only use machine for keep machine in good working condition. A its intended purpose and never make machine that is improperly maintained could modifications not approved by Woodstock. malfunction, leading to serious personal injury Modifying machine or using it differently or death.
Model W1706 (Mfg. Since 3/13) POWER.SUPPLY Circuit.Requirements This machine must be connected to the correct size and The.machine.must.be.properly.set.up. type of power supply circuit, or fire or electrical damage before.it.is.safe.to.operate..DO.NOT. may occur. Read through this section to determine if connect.this.machine.to.the.power. an adequate power supply circuit is available for this source.until.instructed.to.do.so.in.the.
Model W1706 (Mfg. Since 3/13) Grounding.Requirements In the event of certain types of malfunctions or The.machine.must.be.properly.set.up. breakdowns, grounding provides a path of least resistance before. it. is. safe. to. operate.. DO. NOT. for electric current to travel— in order to reduce the risk connect.
Model W1706 (Mfg. Since 3/13) SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1706.
Model W1706 (Mfg. Since 3/13) Machine.Placement Cleaning.Machine •. Floor.Load: This machine distributes a The table and other unpainted parts of your heavy load in a small footprint. Some bandsaw are coated with a waxy grease that protects them from corrosion during shipment. residential floors may require additional Clean this grease off with a solvent cleaner or bracing to support both machine and...
Model W1706 (Mfg. Since 3/13) Setup.Procedures Before connecting your bandsaw to power for the first time and performing the Test.Run on Page.16, you MUST successfully complete the following tasks in the given order per the instructions on the referenced pages: 1.
Page 14
Model W1706 (Mfg. Since 3/13) 5. Remove the insert and the table slot locking pin from the table. 6. Line up the table slot with the blade, position the table so that the blade is in the center cut-out. Table 7.
Model W1706 (Mfg. Since 3/13) 12. Place the fence assembly onto the front rail and position it to the left of the table insert, then secure it in place by pressing down on the lock lever (see Figure.12). Lock Lever Figure.12.
Model W1706 (Mfg. Since 3/13) Blade.Tracking Blade tracking is affected by the tilt of the upper wheel NOTICE (known as center tracking) and the alignment of both wheels (known as coplanar tracking). If,.after.properly.performing.the.blade. tracking. procedure,. the. blade. is. still. The wheels on this bandsaw were aligned at the factory, not.tracking.correctly,.refer.to.Aligning so center tracking is the only adjustment that needs to be Wheels on.
Model W1706 (Mfg. Since 3/13) 6. Rotate the upper wheel by hand several times (at CENTER TRACKING least three) and watch how the blade rides on the wheel crown. See Figure.15 for an illustration of Blade Centered this concept. on Peak of Crown —...
Model W1706 (Mfg. Since 3/13) Test.Run Once the assembly is complete, test run your machine to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page.
Model W1706 (Mfg. Since 3/13) Tensioning.Blade A properly tensioned blade is essential for making accurate cuts, extending the life of the blade, and making many other bandsaw adjustments. For instance, every time you replace the blade, you must perform this procedure because all blades tension differently.
Model W1706 (Mfg. Since 3/13) Adjusting.Positive.Stop After using the table at a tilt of other than 0°, the positive stop allows the table to be quickly and accurately returned to the horizontal position in relation to the blade. This is important for accurate cutting results. Note:.The height of the positive stop is lowered when the table is tilted to the left.
Model W1706 (Mfg. Since 3/13) Aligning.Table To ensure cutting accuracy when the table is first installed, the table should be aligned so the miter slot is parallel to the bandsaw blade. This procedure works best with a ⁄ " blade. Tools.Needed.
Model W1706 (Mfg. Since 3/13) Aligning.Miter.Gauge. Body To ensure accurate cutting results when using the miter gauge, the miter gauge body must be aligned with the blade. Tools.Needed. Machinist's Square ..........1 Phillips Screwdriver..........1 To.align.the.miter.gauge.body,.do.these.steps: 1.. Install the widest blade possible, then make sure the blade is properly tensioned (refer to Page.17) and is tracking correctly (refer to Page.14).
Model W1706 (Mfg. Since 3/13) Adjusting.Fence The fence must be aligned with the blade to ensure accurate cutting results. This is best done by aligning the fence with the miter slot after the table is properly aligned. Tools.Needed. Hex Wrench 5mm ..........1 Wrench 10mm ...........1 To.align.the.fence.with.the.miter.slot,.do.these.steps: 1.
Model W1706 (Mfg. Since 3/13) Adjusting.Blade.Support. Bearings The support bearings are positioned behind the blade and NOTICE support the back of the blade during cutting operations. Proper adjustment of the support bearings is an important Whenever.changing.a.blade.or.adjusting. part of making accurate cuts and also keeps the blade the.tension.or.tracking,.the.upper.and.
Page 25
Model W1706 (Mfg. Since 3/13) 7. Loosen the thumbscrew on the support bearing adjustment shaft (see Figure.27). 0.016" 8. Use the knurled knob to position the support bearing approximately 0.016" away from the back of the blade, as illustrated in Figure.29. Tip:.For a quick gauge, fold a crisp dollar bill in half twice (four thicknesses of a dollar bill is approximately 0.016") and place it between...
Model W1706 (Mfg. Since 3/13) Adjusting.Blade.Guide. Bearings The blade guides provide side-to-side support to keep NOTICE the blade straight while cutting. The blade guides are designed to be adjusted in two ways—forward/backward Whenever.changing.a.blade.or.adjusting. and side-to-side. Properly adjusted blade guides are the.tension.or.tracking,.the.upper.and.
Page 27
Model W1706 (Mfg. Since 3/13) 7. Loosen the cap screws behind the guide bearings (see Figure.31), then open the upper wheel cover. 8. Rotate the upper wheel with one hand, and use the hex wrench to rotate the eccentric guide bearings until they just begin to rotate with the blade (see Figure.33).
Model W1706 (Mfg. Since 3/13) OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine.
Model W1706 (Mfg. Since 3/13) Operation.Overview Disabling.&.Locking. Switch The purpose of this overview is to provide the novice machine operator with a basic understanding of how The ON/OFF switch can be disabled and the machine is used during operation, so the machine locked with the provided padlock (see controls/components discussed later in this manual are Figure.34).
Model W1706 (Mfg. Since 3/13) Basic.Controls Refer to Figures.35–37 and the descriptions below to better understand the basic controls and components of this bandsaw. A.. ON/OFF.Buttons:.Turns the motor ON and OFF. B.. Upper.Wheel.Cover.Knob:.Enables access to the upper wheel compartment. C.. Fence.and.Miter.Gauge:.Allows for controlled cutting at various angles.
Model W1706 (Mfg. Since 3/13) Cutting.Overview The Model W1706 is capable of performing the following cuts: • Miters • Compound Angles • Angles • Simple/Complex Curves • Resawing • Duplicate Parts • Ripping • Circles • Crosscutting • Beveled Curves Workpiece.Inspection Some wood workpieces are not safe to cut or may require modification before they are safe to cut.
Model W1706 (Mfg. Since 3/13) • Wet.or."Green".Stock: Cutting wood with a moisture content over 20% causes unnecessary wear on the blade and yields poor results. Because.of.the.unpredictable.nature. of.cutting.warped.stock,.use.extreme. Excessive.Warping: Workpieces with excessive • caution..The.difference.between. cupping, bowing, or twisting are dangerous to acceptable.and.unacceptable.warped.
Model W1706 (Mfg. Since 3/13) Table.Tilt The table tilts 45° to the right and 10° to the left for a wide range of cutting options. If. the. bandsaw. should. unexpectedly. To.tilt.the.table,.do.these.steps: start.when.making.adjustments,.severe. personal. injury. could. result.. ALWAYS. 1. DISCONNECT BANDSAW FROM POWER! disconnect.
Model W1706 (Mfg. Since 3/13) Ripping Ripping is the process of cutting with the grain of the wood stock. For plywood and other processed wood, ripping simply means cutting down the length of the NEVER.place.fingers.or.hands.in.the. workpiece. For ripping, a wider blade is better. In most line.of.cut..In.the.event.that.something.
Model W1706 (Mfg. Since 3/13) Crosscutting Crosscutting is the process of cutting across the grain of wood. For plywood and other processed wood, crosscutting simply means cutting across the width of the material. To.make.a.90˚.crosscut,.do.these.steps: 1. Mark the workpiece on the edge where you want to begin the cut.
Model W1706 (Mfg. Since 3/13) Resawing Resawing (see Figure.44 for an example) is the process of cutting a board into two or more thinner boards. The maximum board width that can be resawn is limited by When.resawing.thin.pieces,.a. the maximum cutting height of the bandsaw. Maximum wandering.blade.(blade.lead).can.tear.
Model W1706 (Mfg. Since 3/13) Cutting.Curves When cutting curves, simultaneously feed and turn the NOTICE stock carefully so that the blade follows the layout line without twisting. Use either a narrower blade or a blade The.chart.below.displays.blade.widths. with more TPI (teeth per inch), or make more relief cuts, and.the.corresponding.minimum.radii.
Model W1706 (Mfg. Since 3/13) Blade.Speed The Model W1706 offers blade speeds of 1800 and 3100 FPM (Feet Per Minute). For general woodworking and most cutting operations, we recommend using the 3100 FPM speed. Keep in mind, the results from different speeds are related to the type of blade being used.
Model W1706 (Mfg. Since 3/13) Blade.Information Selecting the right blade requires a knowledge of the various blade characteristics to match the blade with the particular cutting operation. Blade.Length Measured by the circumference, blade lengths are usually unique to the brand of your bandsaw and the distance between wheels.
Page 40
Model W1706 (Mfg. Since 3/13) Tooth.Style Figure.49.illustrates.the.three.main.tooth.styles: Raker: Considered to be the standard because the • tooth size and shape are the same as the tooth gullet. The teeth on raker blades usually are very numerous, have no angle, and produce cuts by scraping the material.
Model W1706 (Mfg. Since 3/13) Blade.Changes To.change.the.blade,.do.these.steps: 1. DISCONNECT BANDSAW FROM POWER! 2. Put on heavy leather gloves and safety glasses. If. the. bandsaw. should. unexpectedly. 3. Release the blade tension by moving the tension start. up. when. the. wheel. covers. are. quick release lever all the way left.
Dealer. If you do not have a dealer in your area, these products are also available through online dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at: 1-800-840-8420 or at sales@woodstockint.com.
Model W1706 (Mfg. Since 3/13) MAINTENANCE General Regular periodic maintenance on your machine will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. On.a.daily.basis,.check.for.the.following.conditions. and.repair.or.replace.when.necessary: • Loose mounting bolts. MAKE. SURE. that. your. machine. is. •...
If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. Redressing.Rubber.Tires MAKE.
Model W1706 (Mfg. Since 3/13) Belt.Service To ensure optimum power transmission from the motor to the blade, the belt must be in good condition and operate under proper tension. The belt should be checked for cracks, fraying, and wear. Belt tension should be checked at least every 3 months—more often if the bandsaw is used daily.
Page 46
Model W1706 (Mfg. Since 3/13) Replacing.Belt Tools.Needed. Socket 12mm w/Extension ........1 Wrench or Socket 13mm ........1 To.replace.the.belt,.do.these.steps: 1. DISCONNECT BANDSAW FROM POWER! 2. Open both wheel covers, remove the bandsaw blade, and loosen the motor mount bolts shown in Figure.54 on the previous page. 3.
Model W1706 (Mfg. Since 3/13) Shimming.Table To ensure accuracy when cutting stacked workpieces or circles, the table should be 90° to the back of the blade, as illustrated in Figure.56. If the table is not perpendicular to the back of the blade, the table will need to be shimmed.
Model W1706 (Mfg. Since 3/13) Blade.Lead Bandsaw blades may wander off the cut line when sawing, as shown in Figure.58—this is called blade lead. Blade lead is usually caused by too fast of a feed rate, a dull or damaged blade, or improper blade tension. If your blade is sharp/undamaged, properly tensioned and you still have blade lead, perform the following procedures.
Model W1706 (Mfg. Since 3/13) Tool.Needed. Wrench or Socket 10mm ........1 The.skew.the.table,.do.these.steps: 1. On a scrap piece of wood, mark a line that is perpendicular to the front edge. Starting where the line begins, cut the board by pushing it through the blade with the miter gauge.
Page 50
Model W1706 (Mfg. Since 3/13) 3. With the blade installed and properly tensioned, hold a straightedge close to the center of both wheels. Make sure the straightedge fully extends across the wheels, as shown in Figure.61 on the previous page. —...
Page 51
Model W1706 (Mfg. Since 3/13) Shimming.a.Wheel 1. DISCONNECT BANDSAW FROM POWER! 2. With a straightedge touching both points of whichever wheel is forward most, measure the distance the straightedge is away from the out- of-adjustment upper wheel (see Figure.63 for an example).
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this diagram carefully. If you notice differences between your machine and these wiring diagrams, call Woodstock International Technical Support at (360) 734-3482.
Model W1706 (Mfg. Since 3/13) Troubleshooting This section covers the most common problems and corrections with this type of machine. WARNING!.DO.NOT.make.any.adjustments.until.power.is.disconnected.and. moving.parts.have.come.to.a.complete.stop! PROBLEM POSSIBLE.CAUSE CORRECTIVE.ACTION Motor will not start. 1. Low voltage. 1. Check power supply for proper voltage. 2. Open circuit in motor or loose 2.
Model W1706 (Mfg. Since 3/13) Fence.&.Miter.Gauge 77-1 107-1 114-5 77-3 114-8 114-9 114-14 114-1 77-2 Fence Assembly With Rails 114-10 114-13 114-11 114-7 114-6 114-4 114-2 114-12 114-3 -57-...
Page 60
Model W1706 (Mfg. Since 3/13) Fence.&.Miter.Gauge.Parts.List PART # DESCRIPTION PART # DESCRIPTION XPS22 PHLP HD SCR 10-24 X 5/8 114-4 X1706114-4 STOP DOWEL XPCAP44 CAP SCREW 1/4-20 X 2-1/2 114-5 X1706114-5 HANDLE 1/4-20 XPS49 PHLP HD SCR 8-32 X 1-1/4 114-6 X1706114-6 POINTER X1706036...
Page 62
Fold along dotted lIne place stamp Here Woodstock international inc. p.o. box 2309 bellingham, Wa 98227-2309 Fold along dotted lIne tape along edges--please do not staple...
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox machine or machine part, which in normal use has proven to be defective, provided that the original owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase of the product within two years, and provides Woodstock International, Inc.
Page 64
High Quality Machines and Tools Woodstock International, Inc. carries thousands of products designed to meet the needs of today's woodworkers and metalworkers. Ask your dealer about these fine products:...