Zenith P42W34 Installation And Operating Manual page 34

Externa! Contro! Device Setup
Use this function to specify a TV _D number.
Refer to 'Rea_ Data Mapping 1 '. See page 35
1. Press the MENU button and then use A ,'V button to sele_ the _£CL&t- menu.
2. Press the I_ button and then use A / V button to select _ _.
3. Press the I1_button and then use _1._I_ button to adjust Set ID to choose the desired
TV _D number. The adjustment range of Set m is 1 - 99.
4. Press the ENTER button to save.
• Baud rate : 115200 bps (UART)
• Data length : 8 bits
• Parity : None
* Use a crossed (reverse) cable.
• Stop bit : 1 bit
• Communication code : ASCii code
COMMAND ! COMMAND 2 DATA
(Hexa_cirnal_
01, Pcwer k a 0 -_ 1
02 !nput _!_ .................. k .............. b .............. .....
03, Aspect Ratio k c 0 -_ 3
04, Screen Mute k d 0 _ 1
05, Volume Mute k e 0 '- 1
06. Volume Control k f 0 _ 64
07 Corrirasf k ,q 0 '_ 64
08 Br_htness k h 0 _ 64
09. Octet k i 0 "- 64
10. Tint k i 0 ._ 64
1I, Sharpness k k 0 _ 64
12, OSD _ k I 0 _ 1
13, Remote Control Lock M_ k m 0 _ 1
14 PIP/DW k n 0 _ 3
15, PIP Aspect Ratio k o 0 _ 1
16, Split Zoom k _ 21 -_99
17, PIP Posifi_ k q 0 - 3
18 TreNe k r 0 '- 64
19. _s k s 0_64
20. _ance k t 0 "- 64
21, Coior Temperd_re k ..... y ...... 0,:-3 .....
22 Red Adju_ent k v 0 _ C8
23. Green Adjustment k w 0 _ C8
24 Blue Adjustment k $ 0 -- C8
25 PIP Input Source k y 0 _ 6
26 A_ormal State k z 0 ~ a
27, ISM Matl_od i p 0 _ 3
28. Low Power j q 0 _ 1
29 O_iter Time Setti_ j r I '_ FE
30. _iter Pixel Se_ng i s 0 _9
31. P_ture Size Setting j t 0 ,_64
for Doub_ Window mode
32. Auto _figure j u 1
• Menu doesn't display on _reen when setting the 4
12 13, and 26 ~ 32
Transrrfissien
[Commandl][Command2][ ][_t tD}[ ][Data][Cr] ]
[Command 1]: First command to contro_ the TV. (j or Ix)
[Command 2]: _cond command to control the TW
[Set _D]: You can adjust the set ID to choose desired TV tD
number in Special menu, Adjustment range is 1 "_
99. When selecting Set iD '0' every connected the
TV is co_rolled. Set tD is indicated as decima_
(1 .-99) on menu and as Hexa decimal (OxO.-Ox63)
on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
[C_: Carriage Return
ASCH code 'OxOD'
* [ ]: ASCII code 'space (Ox20)'
OK Acknowledgement
l[Command2l[ ][Set ID][ ][OKl[Data][x]
I
* The TV transmits ACK (acknowiedgement) based on this
format when receiving normal data. At this time, if the data
is data read mode, it indicates present status data, If the
data is data write mede, if returns the data of the PC com-
puter
Error Acknowledgement
[[Command2][ ][Set _DI[ ][NGl[Data][x I l
* The TV transmits ACK (acknowledgement) based on this
format when receiving abnormal data from nonviable
fundions or communication errors
Da_ 1 : tliegat Code
2: Not supported function
3: Wait more time
34 Plasma TV