Code Entry Code Setup Options:.Pressing.OK at.the.CODE.SETUP.screen.presents. 3.options.for.programming.a.Mode.with.codes..These.are.LIST.CODES. (lets.you.enter.a.4.digit.code.from.the.on-screen.code.list),.ENTER.CODES,. (lets.you.enter.a.4.digit.code.directly.from.the.printed.code.list).SEARCH. CODES,.(lets.you.search.through.the.codes.stored.in.the.remote.to.find. the.correct.one.for.your.device). Code Entry using On-screen Code List 1..Manually.turn.on.the.device.to.be.controlled. 2..Press.and.hold.the.SETUP button.until.CODE.SETUP.is.displayed. (takes.about.3.seconds),.then.release.the.SETUP button. 3..Press.and.release.OK..LIST.CODES.is.displayed. 4..Press.and.release.OK..MODE.KEY?.is.displayed. 5..Press.and.release.the.desired.mode.button.(TV,.VCR,.DVD,.etc.)..The. Mode.is.displayed.along.with.its.currently.programmed.code.. 6..Using.the.UP/DOWN.buttons,.select.the.Device.type.to.be. programmed.(TV,.VCR,.DVD,.etc..Note - For TV Mode, only a TV Device can be selected. 7..Press.and.release.OK to.confirm.selection.. 8..The.Code.List.Brand.and.Code.will.now.be.displayed.(e.g..Admiral.
Setup, cont. System Setup Options Pressing. OK at. the. SYSTEM. SETUP. screen. accesses. the. System. Setup. Options.for.Volume.Punch-Through.control.Setup,.Time.Setup,.Date.Setup,. Backlight.Setup.and.System.Reset. Volume/Mute Control and Punch-Through Feature Your.remote.allows.you.to.select.which.device.mode.controls.VOLUME. and.MUTE..This.remote.is.initially.set.for.all.device.modes.to.use.their. own.Volume/Mute.control.if.present..If.the.programmed.code.does.not. have.Volume/Mute.operation,.then.VOLUME.and.MUTE.will.“punch- through”.(hand-over).control.to.the.TV.mode.device.without.you. needing.to.change.to.TV.mode..Note:.Any.mode.chosen.for.Volume/ Mute.control.must.have.its.own.Volume/Mute.function.or.else.VOLUME. and.MUTE.will.not.function. Setting ALL Volume/Mute Control to any one Mode (ALL VOL. SET) This.routine.can.set.all.Modes.to.“punch-through”.to.any.one.chosen.
Setup, cont. Timer Setup Pressing.OK at.TIMER.SETUP.accesses.the.available.Timer.Options.. These.are.a.TV.Sleep.Timer.and.4.Timers.that.can.send.a.sequence.of. up.to.3.key.commands.at.the.preset.time. Setting and Clearing a TV Sleep Timer (TV Sleep Setup) The.remote.can.be.programmed.with.a.TV.Sleep.Timer..At.the.end.of. the.set.Timer.period,.the.remote.sends.the.Power.command.for.the. TV.Mode.device..The.TV.Sleep.Timer.can.be.set.for.a.period.of.1-90. minutes..The.“Zzz”.symbol.is.displayed.when.a.TV.Sleep.Timer.is.set. To set a TV Sleep Timer (no “Zzz” in normal display) 1..Turn.on.the.TV.Mode.device. 2..Press.and.hold.the.SETUP.button.until.CODE.SETUP.is.displayed.(takes. about.3.seconds),.then.release.the SETUP.button. 3.. Press. the. down. navigation. button. repeatedly. until. TIMER. SETUP. is. displayed..Press.and.release.OK.
Page 15
Setup, cont. To set a Timer (Note, the Timer must be cleared first if it was previously set – see To Clear a Timer below) 1.. Press.and.hold.the.SETUP.button.until.CODE.SETUP.is.displayed.(takes. about.3.seconds),.then.release.the SETUP.button. 2.. Press. the. down. navigation. button. repeatedly. until. TIMER. SETUP. is. displayed..
Code Learning Tips On Learning You.can.only.learn.one.device.type.under.any.one.Mode.button.e.g.. only.learn.TV.codes.under.the.TV Mode,.DVD.codes.under.the.DVD Mode,.etc..If.you.are.trying.to.learn.from.a.“Universal”.remote,.it.might. have.more.than.one.code.type.stored.under.a.Mode..Try.learning.from. another.remote.to.see.if.there’s.a.problem.with.the.type.or.brand.of. remote.you.are.trying.to.learn.from.. a. Some functions from some types of remotes might not be able to be learned. b. No functions may be stored under the SETUP button. c. Only one original device type can be learned per individual Mode. d.
Page 17
Tips On Learning, cont. Tips On Learning, cont. m. If.learning.the.first.or.second.buttons.for.a.Mode.results.in. continuous.errors.then.try.the.following: i... End.the.Learn.session.by.pressing.the.EXIT button. ii...Clear.out.the.learned.commands.for.that.Mode. iii... C heck.the.IR.transmitters.are.correctly.aligned.between.the.two. remotes. iv... A djust.the.distance.between.the.two.remotes.to.be.closer.(e.g.. half.an.inch).or.a.further.away.(e.g..2.inches).from.each.other. v...Try.learning.the.original.remote.for.that.Mode.again. If.problems.reoccur.with.the.same.button.check.the.original.remote. button.being.learned.–.does.it.transmit?.Does.it.operate.the.target. device?.Try.learning.that.button.under.a.different clear.Mode..If.it.learns. okay.then.it.is.likely.to.be.a.different.code.type.from.the.others.and. cannot.be.learned.under.the.same.Mode. Learning Notes 1.. You.cannot.learn.under.the.Setup.button. 2.. All.learned.commands.for.a.Mode.are.deleted.if.the.same.or.a.new. 4-digit.code.is.entered.for.that.Mode.by.any.Code.Entry.or.Code. Search. 3.. The.Backlighting.is.turned.off.for.Learning.
Troubleshooting Remote does not operate your product. •.Press.the.mode.button.of.the.product.you.want.to.control. •.Program.the.remote.with.a.new.code. •.Install.new.batteries..(You.might.have.to.reprogram.your.remote.after. installing.new.batteries.) •.Remote.may.not.be.compatible.with.your.product. Remote does not operate some features of your product. •.Program.remote.with.a.new.code. •.Remote.may.not.be.able.to.operate.all.features.of.your.product.or. button.names.might.be.different.than.your.product. Lost Your Codes? Should.you.lose.your.codes.or.programming.instructions,.you.can.find. available.on.our.website: www.jascoproducts.com This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause...