1. Manuals
  2. Brands
  3. Sony Manuals
  4. Projector
  5. VPL VPL-HW15
  6. Protocol manual

Sony VPL-HW15 Protocol Manual

Hide thumbs Also See for VPL-HW15:
Table of Contents

Advertisement

Quick Links

VIDEO PROJECTOR
VPL-HW15
PROTOCOL MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony VPL-HW15

Summary of Contents for Sony VPL-HW15

  • Page 1 VIDEO PROJECTOR VPL-HW15 PROTOCOL MANUAL 1st Edition...
  • Page 2 ! WARNING This manual is intended for qualifi ed service personnel only. To reduce the risk of electric shock, fi re or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualifi ed to do so. Refer all servicing to qualifi...

  • Page 3: Table Of Contents

    Table of Contents 1. Overview 1-1. Introduction ................ 1 1-2. Glossary of Terms .............. 1 1-3. Protocol Stack Structure ............. 1 2. Common Commands 2-1. Sub Commands ..............2 2-1-1. ITEM List ..............2 2-1-2. Infrared Remote Command Code ......6 2-2.

  • Page 5: Introduction

    1. Overview 1-1. Introduction The projector is remotely controllable over RS-232C. It is useful for setting up the projector away from the operator. This protocol manual describes the specifi cations such as packet format and procedures for controlling the projector. In the following sections below, the term “CONTROLLER”...

  • Page 6: Common Commands

    2. Common Commands 2-1. Sub Commands Sub Command is the value which is used by Simplifi ed Command. Value is assigned for executing func- tion. For example, if you want to change the picture mode, the appropriate value assigned for the desired picture mode should be chosen.
  • Page 7 <Table 1> <Table 2> Remarks Item Number Data Item Upper byte Lower byte Data Upper byte Lower byte Film Mode 0000h Set/Get Auto1 0001h Auto2 0002h Gamma Correction 0000h Gamma 1 0001h Gamma 2 0002h Gamma 3 0003h Gamma 4 0004h Gamma 5 0005h...
  • Page 8 Table 2-2 ITEM List For Screen <Table 1> <Table 2> Remarks Item Number Data Item Upper byte Lower byte Data Upper byte Lower byte Wide Mode Full 0000h Set/Get Normal 0001h Wide Zoom 0002h Zoom 0003h Full1 0007h Full2 0008h Over Scan 0000h 0001h...
  • Page 9 Table 2-4 ITEM List For Status <Table 1> <Table 2> Remarks Item Number Data Item Upper byte Lower byte Data Upper byte Lower byte Status Error NO ERROR 0000h Get only LAMP ERROR 0001h FAN ERROR 0002h COVER ERROR 0004h TEMP ERROR 0008h D5V ERROR...

  • Page 10: Infrared Remote Command Code

    2-1-2. Infrared Remote Command Code Tables are shown per function category. . 15 bit PROJECTOR: Table 2-6-Table 2-9 . 20 bit PROJECTOR-E: Table 2-6-Table 2-9 . 20 bit PROJECTOR-EE: Table 2-10 Table 2-6 Infrared Remote Command Code For Picture CATEGORY Code Name 15 bit...
  • Page 11 Table 2-7 Infrared Remote Command Code For Screen CATEGORY Code Name 15 bit 20 bit PROJECTOR PROJECTOR-E PITCH SHIFT PHASE WIDE MODE TOGGLE Table 2-8 Infrared Remote Command Code For Setup CATEGORY Code Name 15 bit 20 bit PROJECTOR PROJECTOR-E POWER ON/OFF PICTURE MUTING STATUS ON...

  • Page 12: Reply

    Table 2-10 Infrared Remote Command Code for 20 bit PRJECTOR-EE CATEGORY Code Name 20 bit PROJECTOR-EE OPTIONS EXIT SYNC MENU ON/OFF PLAY STOP PAUSE FAST REWIND FAST FORWARD PREVIOUS NEXT 2-2. Reply <Table 3> Item Number Data Item Data Upper byte Lower byte COMPLETE UNDEFINED COMMAND...

  • Page 13: Rs-232C

    3. RS-232C 3-1. Connection The RS-232C pin assignment is shown below. REMOTE: RS-232C (D-sub 9-pin, Female) _ EXT VIEW _ Pin No. Signal name Function N.C. Receive Data Transmit Data N.C. Signal Ground N.C. N.C. N.C. N.C. 3-2. Communication Specifi cations .

  • Page 14: Communication Procedure

    3-3. Communication Procedure RS-232C communication sequence is shown below. Each command must be issued by CONTROLLER and PROJECTOR responses to it. CONTROLLER PROJECTOR Send Command The command is executed if it’s valid. Then, the receive command is sent to the CONTROLLER. Receive Command (ACK/NAK/REPLY) Send Command (Infrared Remote Command)

  • Page 15: Command Block Format

    3-4. Command Block Format There are 2 types of block format for RS-232C as shown in the Fig. 1-1. In this section, the block format for Simplifi ed Command and Simplifi ed Variable Length Command are provided. 3-4-1. Simplifi ed Command [Send] The block format for sending request is shown below.

  • Page 16: Packet Examples

    3-5. Packet Examples 3-5-1. Change “Wide Mode” to “Zoom” START CODE = A9h ITEM NUMBER = 0020h (Wide Mode) SET/GET = 00h (SET) DATA = 0003h (Zoom) CHECK SUM = 23h END CODE = 9Ah You will receive the packet below if the process is successfully completed. START CODE = A9h ACK/NAK = 0000h (Complete) ACK = 03h...
  • Page 17 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
  • Page 18 VPL-HW15 (J) VPL-HW15 (SY) Printed in Japan Sony Corporation VPL-HW15 (UC) E 2009. 8 22 9-968-699-01 ©2009...

Table of Contents