INSTRUCTION MANUAL ……………………………………………………………………. 1 Important Safety Instruction 1. Read these instructions. 2. Keep these Instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Page 5
receptacles and the point where they exit from the apparatus. 11. Only use attachment/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Page 6
This symbol is intended to alert the user to the presence of uninsulated : dangerous voltage with in the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.
Page 7
NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 9
A. BOTTOM PANEL CONTROL 1. HDMI IN 2. DVI IN 3. VGA(D-SUB) IN 4. PC STEREO IN 5. AUDIO OUT(Speaker) 6. COMPONENT Y,Pb,Pr & SOUND L,R IN 7. DC 12V IN 8. TRIGGER INPUT B. SIDE PANEL CONTROL 1. VIDEO1(AV1) IN 2.
6 ……………………………………………………………………. INSTRUCTION MANUAL C. REMOTE CONTROLLER (Option) 1. POWER( Turn the power ON or OFF. There will be a few seconds delay before the display appears. 2. SOURCE Select pc or video(AV1/AV2/S-Video/Component/HDMI/DVI/PC) sources. 3. AUTO Auto geometry adjustment in PC Source. 4.
Page 11
Select AV mode.(AV1, AV2 & S-VIDEO). 24. COMP Select COMPONENT mode. INSTRUCTION MANUAL ……………………………………………………………………. 7 D. FRONT KEY CONTROL 1 / 2. Adjust the volume and menu settings. 3 / 4. ▲ / ▼ These buttons allow user to enter the sub-menu of the activated function. The up(▲) button is HOLD function and stop the Trigger &...
9. POWER LED The power LED lights with green when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes Red. 8 ……………………………………………………………………. INSTRUCTION MANUAL OSD MENU DESCRIPTION A: CUSTOM MENU (Only Video Input) 1) Press the MENU button and then press the up(▲) or down(▼) button to select the Custom.
Page 13
Tint: Increase or decrease the tint of the picture. Sharpness: Increase or decrease the sharpness of the picture. A: CUSTOM MENU (For HDMI, DVI & PC Input) 1) Press the MENU button and then press the up(▲) or down(▼) button to select the Custom. 2) Press the up(▲) or down(▼) button to select the sub menu.
Page 14
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Picture / Sound. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Picture Mode. 4) Press the right(▶) or SOURCE/SELECT button. 5) Press the up(▲) or down(▼) button to select the Picture Mode option.
Page 15
4) Press the MENU button to save. 10 ……………………………………………………………………. INSTRUCTION MANUAL 3. Mute 1) Press the up(▲) or down(▼) button to select the Mute. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save.
Page 16
1) Press the up(▲) or down(▼) button to select the Volume 2) Press the left(◀) or right(▶) button to adjust Volume setting. 3) Press the MENU button to save. INSTRUCTION MANUAL ……………………………………………………………………. 11 5. Size...
Page 17
1) Press the up(▲) or down(▼) button to select the Size 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Size option. 4) Press the MENU button to save. 6. NR 1) Press the up(▲) or down(▼) button to select the NR. 2) Press the right(▶) or SOURCE/SELECT button.
Page 18
7. 3D Comb 1) Press the up(▲) or down(▼) button to select the 3D Comb. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save. B.
Page 19
4) Press the right(▶) or SOURCE/SELECT button. 5) Press the up(▲) or down(▼) button to select the Picture Mode option. 6) Press the MENU button to save. INSTRUCTION MANUAL ……………………………………………………………………. 13 2-1. Color Tone 1) Press the up(▲) or down(▼) button to select the Color Tone. 2) Press the right(▶) or SOURCE/SELECT button.
Page 20
3) Press the left(▶) or SOURCE/SELECT button again. 4) Press the up(▲) or down(▼) button to select the Color Tone option. 5) Press the MENU button to save. 14 ……………………………………………………………………. INSTRUCTION MANUAL 2-2. Color Tone (Custom)
Page 21
1) Press the up(▲) or down(▼) button to select the Custom in the Color Tone. 2) Press the Menu button to save. 3) Press the up(▲) or down(▼) button to select the Red(R), Green(G) or Blue(B). 4) Press the left(◀) or right(▶) button to adjust color density. 5) Press the MENU button to save.
Page 22
INSTRUCTION MANUAL ……………………………………………………………………. 15 3. Size 1) Press the up(▲) or down(▼) button to select the Size. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Size option. Input 4. PC control (Only PC 1) Press the up(▲) or down(▼) button to select the PC.
Page 23
4) Press the right(▶) or SOURCE/SELECT button. 5) Press the left(◀) or right(▶) button to adjust the PC setting. 6) Press the MENU button to save. Auto Adjust: Auto geometry adjustment. Phase: Adjust the number of horizontal picture elements. H-Position: Move image horizontally on screen right or left. V-Position: Move image vertically on screen up or down.
Page 24
1) Press the right(▶) or SOURCE/SELECT button. 2) Press up(▲) or down(▼) button to select the On or Off. 3) Press the MENU button to save. INSTRUCTION MANUAL ……………………………………………………………………. 17 2. Input Source...
Page 25
1) Press the up(▲) or down(▼) button to select the Input Source. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Source option. 4) Press the MENU button to save. 3. Size 1) Press the up(▲) or down(▼) button to select the Size.
Page 26
18 ……………………………………………………………………. INSTRUCTION MANUAL 4. Position 1) Press the up(▲) or down(▼) button to select the Position. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Position option. 4) Press the MENU button to save. 5.
Page 27
1) Press the up(▲) or down(▼) button to select the Swap. 2) Press the right(▶) or SOURCE/SELECT button to swap the main image for the sub one. INSTRUCTION MANUAL ……………………………………………………………………. 19 5. Sound Select 1) Press the up(▲) or down(▼) button to select the Sound Select. 2) Press the right(▶) or SOURCE/SELECT button.
C. PIP MENU (For HDMI, DVI & PC Input) 1. Input Source 1) Press the up(▲) or down(▼) button to select the Input Source. 2) Press the right(▶) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Input Source option. 4) Press the MENU button to save.
Page 29
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Setup. 1. Reset 1) Press the right(▶) or SOURCE/SELECT button 2) Press the right(▶) or SOURCE/SELECT button again. 3) Press SOURCE/SELECT button to execute the reset. Reset: All settings go to the factory initialization.
Page 30
2. Language 1) Press the up(▲) or down(▼) button to select the Language. 2) Press the right( ) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select language. 4) Press the MENU button to save. 3. OSD Tone 1) Press the up(▲) or down(▼) button to select the OSD Tone.
Page 31
4. Blue Screen 1) Press the up(▲) or down(▼) button to select the Blue Screen. 2) Press the right( ) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save. 5.
Page 32
INSTRUCTION MANUAL ……………………………………………………………………. 23 6. Trigger 1) Press the up(▲) or down(▼) button to select the Trigger. 2) Press the right( ) or SOURCE/SELECT button. 6-1. Trigger Enable 1) Press the up(▲) or down(▼) button to select the Trigger Enable. 2) Press the right( ) or SOURCE/SELECT button.
Page 33
24 ……………………………………………………………………. INSTRUCTION MANUAL 6-2. Trigger Input 1) Press the up(▲) or down(▼) button to select the Trigger Input . 2) Press the right( ) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Trigger Input option. 4) Press the Menu button to save.
Page 34
INSTRUCTION MANUAL ……………………………………………………………………. 25 6-4. Trigger Time 1) Press the up(▲) or down(▼) button to select the Trigger Time. 2) Press left( ) or right( ) button to adjust Trigger Time setting. 3) Press the MENU button to save. 6-5 Trigger Option 1) Press the up(▲) or down(▼) button to select the Trigger Option.
Page 35
N/C (Normal Closed): When Trigger cable is opened, Trigger function is activated. N/O (Normal Opened): When Trigger cable is closed, Trigger function is activated. High: When Trigger signal is high(2~5[V]), Trigger function is activated. Low: When Trigger signal is low(0~0.6[V]), Trigger function is activated. 26 …………………………………………………………………….
Page 36
The Type of Image 2 : Component, HDMI, DVI or PC. INSTRUCTION MANUAL ……………………………………………………………………. 27 7. Auto switching 1) Press the up(▲) or down(▼) button to select the Auto switching. 2) Press the right( ) or SOURCE/SELECT button. 7-1. Auto switching On/Off...
Page 37
1) Press the right( ) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the On or Off . 4) Press the Menu button to save. 28 ……………………………………………………………………. INSTRUCTION MANUAL 7-2. Auto switching Inputs enabled...
Page 38
1) Press the up(▲)or down(▼) button to select the Inputs enabled. 2) Press the right( ) or SOURCE/SELECT button. 3) Press the up(▲) or down(▼) button to select the Input. 4) Press the right( ) or SOURCE/SELECT button. 1) Press the up(▲) or down(▼) button to select the On or Off. 2) Press the Menu button to save.
Page 39
1) Press the up(▲) or down(▼) button to select the Time. 2) Press the left( ) or right( ) button to adjust the Time setting. 3) Press the MENU button to save. 30 ……………………………………………………………………. INSTRUCTION MANUAL...
Page 40
Using the VESA standard wall mount design and the 100mm hole pattern on the back panel to install the LCD monitor to the wall. Wall-mount Installation (Option) 1. The Monitor fixing bracket to the monitor using the fixing screws provided. 2.
Page 41
▶ PIN ASSIGNMENTS Pin 1 RED VIDEO GREEN VIDEO SIGNAL CABLE DETECT BLUE VIDEO GROUND GROUND SDA(for DDC) GROUND H-SYNC.(or H+V SYNC.) RED GROUND V-SYNC. GREEN GROUND SCL(for DDC) BLUE GROUND ▶ ACCESSORIES 1. Power cord 2. Power adaptor (Built-in) 3.
32 ……………………………………………………………………. INSTRUCTION MANUAL This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
Page 46
Tel: +1-626-844-8888 Sales: +1-631-436-5070 Fax: +1-626-844-8838 Fax: +1-631-436-5027 EverFocus Produkt wurde Your EverFocus product is designed entwickelt und hergestellt mit qualitativ and manufactured with high quality hochwertigen Materialien materials and components which can Komponenten, die recycelt und wieder be recycled and reused.