Table of Contents
Advertisement
Universal
Bench Top
TooU Work Stand
Model No.
320,19730
CAUTION:
Read, understand and follow all Safety Rules
and Operating Instructions in this Manual before
using this product..
Sears, Roebuck and Co.
Hoffman Estates, IL 61)179 U.S.Ao
Visit our Craftsman® website:
www.craftsman.com
= WARRANTY
• SAFETY
° UNPACKING
° DESCRIPTION
• ASSEMBLY
° ADJUSTMENTS
° MAINTENANCE
Advertisement
Table of Contents
Related Manuals for Craftsman 320.19730
Summary of Contents for Craftsman 320.19730
- Page 1 Read, understand and follow all Safety Rules = WARRANTY and Operating Instructions in this Manual before • SAFETY using this product.. ° UNPACKING ° DESCRIPTION Sears, Roebuck and Co. • ASSEMBLY Hoffman Estates, IL 61)179 U.S.Ao ° ADJUSTMENTS Visit our Craftsman® website: www.craftsman.com ° MAINTENANCE...
- Page 2 Page Sears Repair Parts Phone Numbers ............Beck Cover ONEYEAR FULLWARRANTY ON CRAFTSMAN _ PRODUCT If this Craftsman product lails due to a defect in material or workmanship within one year from lhe date of purchase, RETURN ITTO THE NEAREST...
- Page 3 ALWAYS wear safety goggles or safety glasses with side shield and a full-face shield when needed, We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shield, available at Sears Stores or other craftsman Outlets_...
- Page 4 Z_ WARNING: BE SURE to read, understand and follow all safety rules and operating Instructions in this manual and the operator's manual of any bench top power tool you use with this Universal Bench Top Toot Work Stand. Failure to do so may result in electrlc shock, fire and / or sertous...
- Page 5 PERSONAL SAFETY conL 8o ALWAYS SECUREYOUR WORK= Use clamps or a vise to hold work when praclicaI. it is safer than _Jsing your hand and frees both hands to operate tool 9_,USE SAFETY EQUIPMENT. Always wear eye protection Dust mask. non-skid safety shoos, hard hat, or hearing protection...
- Page 6 ELECTRICAL SAFETY cent° Double Insulated tools are equipped with a polarized plug (one binds is wider than the other).Thts plug wH! fit in a polarized outlet only one way, If the plug does not tit futiy in the outlet, reverse the plug. If it still does nol lit+ contact a qualified etectrfcian to inslalI a polarized...
- Page 7 EXTENSION CORDS conL z_WARNING: Check extension cords before each use. ifdamaged reptace immediately. Never use toot with a damaged cord since touching the damaged area could cause electrical shock, resulting In serious injury. SAFETY SYMBOLS FOR YOUR TOOL The label on your too! may Include the following symbols.
- Page 8 SAFETY RULES FOR THE USE AND OPERATION OF THE UNIVERSAL BENCH TOP TOOL WORK STAND cont. Z_ WARNING: IFYOU I_OUNT BENCHTOP POWERTOOLS SUCH AS A TABLE SAW OR pLANER TO THE TOOL WORK STAND, the feed direction perpendicular to the axis of the best stability on this tool work stand°...
- Page 9 Toot Work Slend'e operation, If any part is damaged, return the Too] Work Stand to your nearest Sears slore or Craftsman outlet to have the Work Stand rep}aced, Z_ WARNING: If any parts are bent or broken,...
- Page 10 Fig_ 2 Fig,, 3 2o Take hold of red 3 Take hold ofredTableTop Locking/Carrying Handle (A) Assembly Handle (C) and lift and rlght side of the Tab|e Table Top Assembly up as shown° Assembly (B) then unlock LockingJCarr¥tng Handle (A) by pulling handle towards...
- Page 11 Flgo 7 Fig,, 6 7, With your foot still on the Base Hold down the Base Bar Legs Bar, take hold of the Support Bar (F) (as shown) by placing your foot on the Base Bar. Pull theTable and pull up until its Chrome Extenslon Bars are also fully Top Assembly...
- Page 12 Ftgo 11 _-_!'!: _" _' I 10. To change the width of the Table Close up view of Table Top Top Assembly working area, Assembly's clamp knob., turn the TableTop Assemb/y's two Clamp Knobs (I) clockwise to unlock them ss shown Fig 13 :;=_iii_ Be sure that after adjusting...
- Page 13 Fig- 15 Fig,, 14 14., Unlock 3-Inch CasterWheels Lock Caster wheels in place by pushing the Locking Lever to tile by Lilting Locking Lever on "DOWN" position. each wheel to the "UP" position. PARTS LIST t CALLOUTS (Fig. 1B) : Fig,, 16 Spring Loaded P Table Top Handle...
- Page 14 MOUNTNG BENCH TOP TOOL SUCH AS MITER TO THE TOOL WORK STAND (Fig, Before mounling your bench top tool, make sure Ihe Casler Wheels are in the "DOWN" or locked position Check bench top tool |or number of holes and their location for mounting tool This information should be in the manual for the bench top tool...
- Page 15 MOUNTNG BENC H TOP TOOL SUCH AS ATABLE SAW OR PLANER TOTHETOOLWORK STAND (Fig. This method of mounting is used for tools that do not fit the pre-slamped tool mounting slots in the Table Top Assembly el the Tool Work Sland, Examples would be Scoot[or Saw, Drilt Press, Disc/Belt Sander,...
- Page 16 FOLDINGTOOLWORK STAND DOWN STORAGE (Refer to Illustration Figso 1 to 15 on pages 9-13) Once Bench Top Power Tool is removed from Tool Stand; '_ Keep Caster Wheels in locked position by pushing Locktng Lever"Down% 2, Loosen Tool Stand's Clamping Knobs,, Open up Tabfe Top Assembly to its fully extended...
- Page 17 This Universal Toot Stand has the foliowfng features (conto) : plywood mounting used with boards io accommodate most b_ands of bench lop power tools (plywood mounting boards and all mounting hardware sold separately) Large carrying handle locks table in lotd-down position for compacl storage.
- Page 18 UNIVERSAL BENCH TOP TOOL WORK STAND -MODEL NUMBER 320.'19730 t:" 't s:, ..:,gr ,: ,0'_/ ,o '" e ;{,.'," _::i: ¢ :'! _ •. ",Zt .,=r.
- Page 19 UNIVERSAL BENCH TOP TOOL WORK STAND - MODEL NUMBER 320.19730 Description Qty. Description Oty. M8 Nut ..... 6 Moving Handle ..M8 X 38rnm Screw Upper Inner Tube ..1 ..inner Tube Nut End Cover ..MBX 32ram Se_'e,,v "×" Steel Brackel (Rear} M5 X 14mm Screw Protection Jacket el Nu[ Gemel Bracket...
- Page 20 Get it fixed, at your home or ours! Your Home For repair - in your I_ome -of all major brand appliances, lawn and garden equipment, or heabng and cooli_ systems no matter who made Jr, no matter who sold it! For the replacement pa|ts, accessories and owne_ s rnanv_Js that you need to do-i[-youfself...