Gas Connection - Bosch Nexxt WTMC6521UC Operating, Care And Installation Instructions Manual

- the power cord plug fits into the
socket.
- the power cord is acceptable for
use in this application.
- the grounding system is properly
installed.
The power cord may be replaced by an
electrician only.
Replacement power cords are available
from Customer Service.
Volts Hertz Amperes Watts
110-120 60 9 1080
Gas connection
Explosion hazard!
Use a new AGA or CSA approved
gas supply line.
Install a shut-off valve.
Securely tighten all gas
connections.
Have a qualified person make sure
gas pressure does not exceed
14 in. W.C./3.49 kPa/0.506 psig.
(Natural Gas).
Example of a qualified person
include:
- licensed heating personnel,
- authorized gas supplier personnel
- authorized service personnel.
Failure to do can result in explosion
or fire.
Risk of death or injury!
All gas line connections must be
tested for leaks prior to appliance
operation. Apply soapy water to gas
line connections and check for
formation of new bubbles. Bubbles
indicate leak!
When installing the gas supply to the
gas dryer inlet pipe, do not exceed 310
Ibf in (35 Nm).
Never use an open flame to test for
gas leaks.
Gas type
This dryer when equipped for use with
NATURAL GAS will employ an orifice
size 46 and have a gas outlet pressure
of 3.5 in. W.C.
Your dryer must have the correct valve
for the type of gas in your home. Valve
information is located on the rating
plate behind the door below the port
hole.
If the rating-plate information does not
agree with the type of gas available,
contact your dealer or our costumer
service team (see page 27).
Gas supply line
1/2" I.D. pipe is recommended.
3/s" approved tubing is acceptable for
lengths under 20 ft (6.1 m) if local
codes and gas supplier permit.
Must include _/8" NPT plugged
tapping, immediately upstream of the
gas connection.
A shut off valve must be included:
- USA:
An individual manual shut-off valve
must be installed within 6 ft (1.8 m)
of the dryer in accordance with the
National Fuel Gas Code, ANSI
Z223.1.
- Canada:
An individual manual shut-off valve
must be installed in accordance
with the B149, Installation Codes,
CAN/CSA B149.1 and CAN/CSA
B149.2. It is recommended that an
individual manual shut-off valve be
installed within 6 ft (1.8 m) of the
dryer.
5 4 3 2
1
- 1/2"
NPTgassupplyline
2- Gasshut-0ffvalve
3- 1/8" NPTplugged tapping
4 - 3/8" pipeto flare adapterfitting
5 - 3/8"flexiblegasconnector(tothe dryer)
The shut off valve should be easy to
reach for opening and closing.
Note:
The dryer must be checked for proper
operation whenever the gas
connections have been broken.
Dryer gas pipe
The gas pipe that comes out through
the rear of the dryer has a 3/8" male
pipe thread.
_'onnection of the dryer
Connection must be made by
a qualified technician.
The dryer must be disconnected
from the gas supply piping system
during testing pressure.
When using for the first time make
sure that there is no air in the piping
system.
Do not use copper pipes and tubing
if connected to natural gas.
The connection may be different,
according to the supply line type, size
and location.
If local codes permit, use a flexible
stainless steel connector (Design
certified by the America Gas
Association or CSA International)
to connect the dryer.
1 2
To reduce the distance between body
sheet and wall install a 3/8" elbow on
the gas pipe of the dryer.
1 - gas pipe (3/8"malepipethread)
2- 3/8" elbow
Exhaust air connection
1. To reduce the risk of fire, this dryer
MUST BE EXHAUSTED
OUTDOORS.
2. To reduce the risk of fire, do not
use ductwork longer than
recommended.
3. DO NOT use a plastic or
non-metal duct with this dryer.
4. DO NOT use a duct smaller than 4
inches in diameter.
5. DO NOT use exhaust hoods with
magnetic latches.
6. DO NOT exhaust the dryer into a
chimney, furnace cold air duct,
attic, crawl space, or any other
ductwork used for venting.
7. DO NOT install a flexible duct in an
enclosed wall, ceiling or floor.
8. DO NOT crush or kink the duct.
9. Do clean and inspect the exhaust
system on a regular basis; at least
once a year.
10. The exhaust duct must terminate
in a manner to prevent back drafts
or entry of birds or other wildlife.