Summary of Contents for Hitachi CP-X2 - XGA LCD Projector
Page 1
Projector CPX2/CPX6 User's Manual (detailed) Technical Example of PC signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 3.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA...
Page 2
Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some PC models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
Page 3
Connection to the ports Connection to the ports AUDIO OUT USB STORAGE COMPUTER IN DC 5V 0.5A AUDIO IN S-VIDEO VIDEO COMPUTER IN D-sub 5pin mini shrink jack (1) for Computer signal • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) •...
Connection to the ports (continued) AUDIO OUT USB STORAGE COMPUTER IN DC 5V 0.5A AUDIO IN S-VIDEO VIDEO S-VIDEO Mini DIN 4pin jack Signal Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator Brightness signal, 1.0Vp-p, 75Ω terminator Ground Ground VIDEO...
Page 5
Connection to the ports (continued) AUDIO OUT USB STORAGE COMPUTER IN DC 5V 0.5A AUDIO IN S-VIDEO VIDEO USB STORAGE USB A type jack Signal +5V 2 - Data 3 + Data 4 Ground USB B type jack Signal +5V 2 - Data 3 + Data...
Page 6
Connection to the ports (continued) AUDIO OUT USB STORAGE COMPUTER IN DC 5V 0.5A AUDIO IN S-VIDEO VIDEO RJ-45 jack Signal Signal Signal TX + 2 TX - 8 CTS- 3 RX + 6 RX - SD card slot The SD card slot is in the side opposite to the lamp cover of the SD card slot cover...
Command Control via the Network Command Control via the Network Communication Port The following two ports are assigned for the command control. TCP #23 TCP #975 Command Control Settings Configure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Port open...
Command Control via the Network (continued) Command Format [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low: Lower byte of CRC flag for command data CRC_high: Upper byte of CRC flag for command data 3.
Page 9
Command Control via the Network (continued) Decreasing the projector setting value (Decrement command) () The PC sends the following decrement code to the projector. Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’) (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the PC. When the projector cannot understand the received command When the projector cannot understand the received command, the error code ‘15H’...
Command Control via the Network (continued) 7. Reply Data The connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands reply data. ACK reply: ‘06H’ + ‘xxH’ NAK reply: ‘15H’ + ‘xxH’ Error reply: ‘1CH’ + ‘xxxxH’ + ‘xxH’...
Page 11
Command Control via the Network (continued) Network command table Command Data Names Operation Type Header Action Type Setting Code Power Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00 00 60 01 00 BE EF 06 00 19 D3 02 00 00 60 00 00 [Example return] 00 00 01 00 ...
Page 12
Command Control via the Network (continued) Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code User Gamma Pattern BE EF 06 00 FB FA 01 00 80 30 00 00 9 step gray scale BE EF 06 00 6B FB 01 00 80 30 01 00 15 steps gray scale BE EF 06 00 9B FB 01 00 80 30 02 00 Ramp BE EF 06 00 0B FA 01 00...
Page 13
Command Control via the Network (continued) Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code COLOR TEMP GAIN B BE EF 06 00 8C F5 02 00 B3 30 00 00 Increment BE EF 06 00 EA F5 04 00 B3 30 00 00 Decrement BE EF 06 00 3B F4 05 00 B3 30 00 00 COLOR TEMP BE EF 06 00 04 F5 02 00...
Page 14
Command Control via the Network (continued) Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code OVER SCAN BE EF 06 00 91 70 02 00 09 22 00 00 Increment BE EF 06 00 F7 70 04 00 09 22 00 00 Decrement BE EF 06 00 26 71 05 00 09 22 00 00 OVER SCAN Reset Execute BE EF 06 00 EC D9...
Page 15
Command Control via the Network (continued) Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code FRAME LOCK TURN OFF BE EF 06 00 CB D6 01 00 14 30 00 00 TURN ON BE EF 06 00 5B D7 01 00 14 30 01 00 BE EF 06 00 F8 D6 02 00 14 30 00 00 KEYSTONE V BE EF 06 00 B9 D3 02 00...
Page 16
Command Control via the Network (continued) Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code LANGUAGE ENGLISH BE EF 06 00 F7 D3 01 00 05 30 00 00 FRANÇAIS BE EF 06 00 67 D2 01 00 05 30 01 00 DEUTSCH BE EF 06 00 97 D2 01 00 05 30 02 00 ESPAÑOL BE EF 06 00 07 D3...
Page 17
Command Control via the Network (continued) Network command table (continued) Command Data Names Operation Type Header Action Type Setting Code AUTO OFF BE EF 06 00 08 86 02 00 10 31 00 00 Increment BE EF 06 00 6E 86 04 00 10 31 00 00 Decrement BE EF 06 00 BF 87 05 00 10 31 00 00 AUTO ON TURN OFF BE EF 06 00 3B 89...