Related Manuals for EnGenius EPI-3601S
Summary of Contents for EnGenius EPI-3601S
-
Page 1: User Manual
EPI-3601S Wireless LAN PCI adapter Version 1.2 EPI-3601S Wireless LAN PCI Adapter (802.11g & 802.11b up to 108 Mbps) User Manual Version: 1.2... -
Page 2: Table Of Contents
INTRODUCTION..........................3 FEATURES ............................3 PACKAGE CONTENTS ........................4 SYSTEM REQUIREMENTS ......................5 INSTALLATION ..........................5 VERIFY INSTALLATION .......................12 SETUP NETWORK CONFIGURATION (MS WINXP) ...............13 SETUP WLAN (ENGENIUS CLIENT UTILITY) .................15 SYSTEM TRAY UTILITY OPTIONS.....................19 SETUP NETWORK SECURITY (WEP, WPA…) ................25 ............................25 WPA/WPA2..........................26 WPA/WPA2 ......................28 PASSPHRASE 802.1... -
Page 3: Introduction
EPI-3601S Wireless LAN PCI adapter Version 1.2 1 Introduction EnGenius EPI-3601S Wireless LAN PCI Adapter compliant with IEEE802.11g, adopts “Super G” and “Extended Range” WLAN transmission technologies, resulting in transmission speeds of up to 108M, transmission distance is 2-3 times that of the normal 11b, 11g products, transmission range extended to 4-9 times. -
Page 4: Package Contents
EPI-3601S Wireless LAN PCI adapter Version 1.2 * Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g chipset used. Actual throughput may vary. Network conditions and environmental factors lower actual throughput rate. 3 Package Contents Open the package carefully, and make sure that none of the items listed below are missing. -
Page 5: System Requirements
EPI-3601S Wireless LAN PCI adapter Version 1.2 4 System Requirements To begin using the WLAN PCI Adapter, your PC/Notebook must meet the following minimum requirements: Operating System – Microsoft Windows XP/2000 PCI socket x 1 (free to use socket) 256MB RAM memory or higher 750MHz CPU or higher configuration 5 Installation Insert the support CD into your optical drive. - Page 6 EPI-3601S Wireless LAN PCI adapter Version 1.2 Click next to install or click cancel to terminate installation.
- Page 7 EPI-3601S Wireless LAN PCI adapter Version 1.2 Two options are available for installation. Choose one of them and click Next EnGenius Configuration Utility + driver. Driver only. Choose location to install and click Next.
- Page 8 EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose name for program folder to create shortcuts. Click Next. Should you agree with terms and conditions mentioned, Click Next else click Cancel to exit.
- Page 9 EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose Engenius client Utility & supplicant Else choose Third-party supplicant & click Next.
- Page 10 EPI-3601S Wireless LAN PCI adapter Version 1.2 Be patient until the installation process is complete.
- Page 11 EPI-3601S Wireless LAN PCI adapter Version 1.2 Find the item in Start menu...
-
Page 12: Verify Installation
6 Verify installation Verification involves finding EPI-3601S card in System Properties and checking if the driver is installed correctly. 1. Open [Control Panel] =>Double-click [System]. 2. Select [Hardware] tab=>Click [Device Manager]. Select Network Adapters. Click open [EnGenius PCI wireless Network Adapter]... -
Page 13: Setup Network Configuration (Ms Winxp)
EPI-3601S Wireless LAN PCI adapter Version 1.2 Verify that the device status of [EnGenius PCI wireless Network Adapter] [This device is working properly]->Click [OK] 7 Setup Network Configuration (MS WinXP) • Enter [Start Menu] =>select [Control panel] =>select [Network]. •... - Page 14 EPI-3601S Wireless LAN PCI adapter Version 1.2 • Select [Internet Protocol (TCP/IP)] =>Click [Properties]. • Select the [General] tab. a. If your Wireless Router supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].
-
Page 15: Setup Wlan (Engenius Client Utility)
Following steps guides you to initially setup a wireless network connection. If in case any non secure WLAN access point was found by EnGenius Client Utility, it will have already connected to that AP. Notice the EnGenius Client Utility on taskbar shows connected icon. - Page 16 You will see the utility show up as follows. Current Status tab shows information about the ACTIVE network connection. In case there was not any network connection made, it can be manually connected by following the steps listed below. 1. Click open EnGenius Client Utility from start menu. 2. Click open Profile Management.
- Page 17 EPI-3601S Wireless LAN PCI adapter Version 1.2 Click Scan. You will see a window showing all available AP that can be detected by EPI-3601S Wireless LAN card. Click on the SSID that you have security key information or choose an SSID which has no encryption to begin with.
- Page 18 EPI-3601S Wireless LAN PCI adapter Version 1.2 Click Security tab in case the Access point needs security settings. Click Configure. This Access point for instance is WEP key protected. Therefore the corresponding settings have to be keyed in. Type the security key information as appropriate. You will need to have this information ready in hand in case this is a protected network.
-
Page 19: System Tray Utility Options
Return back to profile management tab and click Advanced tab. typically you will notice the following. Clicking OK will result in connecting to the network directly. 9 System Tray Utility options Right click on EnGenius utility icon can help do many activities. Network disconnected Network connected... - Page 20 Version 1.2 Right click options (Radio Enabled) Right click options (Radio Disabled) Choose Exit to quit EnGenius Client utility. Choose Open EnGenius Client Utility If Radio is already disabled, you will see a window as shown below. If Radio is already enabled, you will see a window as shown below.
- Page 21 EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose Preferences. Check the box to choose whether you want the utility to run when Windows starts. Choose Enable Radio and notice the message that confirms the same.
- Page 22 EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose Disable Radio and notice the message that confirms the same. Choose Show Connection Status If WLAN adapter is enabled, you will notice the following window with network connection information. If WLAN adapter is disabled, you will notice the following window with disabled network information.
- Page 23 EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose Select Profile If radio is disabled, grayed out Profile options are shown as below If radio is enabled, available Profiles are shown as below Choose Select Client Software If Radio is enabled, two options are shown as below.
- Page 24 Choose Disable WLAN if LAN is connected. Immediately, if an active LAN connection is detected, EPI-3601SWLAN adapter is disabled. Choose Open EnGenius Client Utility If Radio is already disabled, you will see a window as shown below. If Radio is already enabled, you will see a window as shown below.
-
Page 25: Setup Network Security (Wep, Wpa
If your AP/Router has network security key, your wireless adapter needs to have the same security setting. The details of setting up network security are described below. Please open EnGenius Client Utility. a. None If AP you want to connect has no encryption settings, just simply click in Set... -
Page 26: Wpa/Wpa2
EPI-3601S Wireless LAN PCI adapter Version 1.2 Security Options. b. WPA/WPA2 1. Select WPA/WPA2 under Set Security Options. 2. Choose the correct EAP type. 3. Click Configure. - Page 27 EPI-3601S Wireless LAN PCI adapter Version 1.2 Select the check boxes for Doman Login and Validate Server Identity & choose the Trusted Root Certification Authorities. Provide user information for EAP-TTLS authentication.
-
Page 28: Wpa/Wpa2 Passphrase
EPI-3601S Wireless LAN PCI adapter Version 1.2 Click Settings. c. WPA/WPA2 passphrase If AP includes support for passphrase, the following settings need to be done. In Security tab, select WPA/WPA2 passphrase. Click Configure. You can find the dialog box requests a passphrase. Key in the correct value. Click OK. -
Page 29: Setting 802.1X
EPI-3601S Wireless LAN PCI adapter Version 1.2 The active profile with the security settings is immediately applied. d. Setting 802.1x If AP you want to connect to has 802.1x based other type of authentication, Select 802.1x. Choose the correct 802.1x EAP type. Enable the following check boxes and set the correct value. -
Page 30: Pre-Shared Key - Static Wep
EPI-3601S Wireless LAN PCI adapter Version 1.2 Include the correct Authentication timeout value. Enable No Network Connection Unless User Is Logged In checkbox if appropriate. Else choose User Temproary User Name and password. e. Pre-shared key – Static WEP If Access Point you want to connect to has [WEP] authentication, click the Security tab. -
Page 31: Managing Profiles
EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose Pre-Shared Key. Enable checkbox related to Association to Mixed Cells. Click Configure. Choose the correct WEP Key Size. Choose the appropriate Key entry. Key the values for WEP key. 11 Managing Profiles Click Profile Management tab. - Page 32 EPI-3601S Wireless LAN PCI adapter Version 1.2 Choose a profile. There are several actions to be done on a profile. You can remove it by clicking on remove button. Those profile settings are no longer available again. That needs to recreate the profile if required. You can apply the profile by clicking on Activate button.
- Page 33 EPI-3601S Wireless LAN PCI adapter Version 1.2 Click on the profile you want to import and choose OPEN. Exporting a profile is similar to importing as shown below. Give an appropriate name and save the currently active configuration. Auto ordering Profiles Several profiles can be arranged in a priority or preference based order by clicking the Order Profiles tab.
-
Page 34: Diagnostics
Power saving by disabling WLAN when LAN is Active Enable the checkbox for Disable WLAN if LAN is connected and the changes are instantly applied based on whether a LAN connection is active or not. 12 Diagnostics A wide range of diagnostics is available in EnGenius Client Utility. - Page 35 EPI-3601S Wireless LAN PCI adapter Version 1.2 Click Diagnostics tab to view the Transmit and Receive information in terms of packet numbers sent /received. Click Adapter Information to get information about the H/W and driver information. Click on Advanced Statistics to get information about very detailed TX/RX information.
-
Page 36: Menu
EPI-3601S Wireless LAN PCI adapter Version 1.2 13 Menu The main EnGenius Utility window has 3 menu options to choose from. Action Enable/Disable Radio. This is a toggle feature and appropriate response is shown in dialog boxes below... - Page 37 EPI-3601S Wireless LAN PCI adapter Version 1.2 Enable/Disable Tray icon This option enables or disables system tray icon that represents signal strength and provides other configuration options. Options Display Settings can be changed from % to db and refresh interval can be changed Along with relative or cumulative change in data display.
-
Page 38: Uninstalling Engenius Utility/Driver
EPI-3601S Wireless LAN PCI adapter Version 1.2 Select Client Software – choose the utility to control the EPI-3601S Wireless LAN PCI adapter. WZC and EnGenius and third-party tools are the options available. Help About 14 Uninstalling EnGenius Utility/Driver Select Uninstall option from the start menu. - Page 39 EPI-3601S Wireless LAN PCI adapter Version 1.2 Select Uninstall the previous installation. Click Next. Select OK. Select OK. Rebooting ensures clean uninstall.
- Page 40 EPI-3601S Wireless LAN PCI adapter Version 1.2 Click Yes. If you want to keep it so that you can use it later, select no. Choose to keep or remove the device driver files. Choosing OK will reboot PC.
-
Page 41: Appendix A - Specifications
EPI-3601S Wireless LAN PCI adapter Version 1.2 Appendix A – Specifications 24 @ 36Mbps Data Rates 23 @ 48Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54, 72 and 108Mbps 22 @ 54Mbps 802.11b: 1, 2, 5.5, 11Mbps 2.412~2.462 GHz (IEEE802.11b) Standards / Compliance 27 dBm @1~11Mbps IEEE802.11, IEEE802.11g, IEEE802.11b...