Echo PB-2100 Service Data
  1. Manuals
  2. Brands
  3. Echo Manuals
  4. Blower
  5. PB-2100
  6. Service data

Echo PB-2100 Service Data

Power blower
Hide thumbs Also See for PB-2100:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

See also: Operator's Manual
21-21H-00
INTRODUCTION
We are constantly working on technical
improvement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All
specifications, illustrations and directions in
this SERVICE DATA are based on the latest
products information available at the time of
publication.
ECHO SERVICE MANUAL Ord. 403-11
(Model : PB-2100, PB-2110, ES-2100, ES-
2400) contains lots of information for servicing
this model.
INDEX
PB-2100,PB-2155,PB-2200SI
CONTENTS
1 SERVICE INFORMATION ............................. 2
1-1 Specification ............................................... 2
1-2 Technical data ............................................ 3
1-3 Torque limits ............................................... 4
1-4 Special repairing materials ......................... 4
1-5 Service limits .............................................. 5
1-6 Special tools ............................................... 6
2 EMISSION ADJUSTMENT GUIDE ............... 7
2-1 General adjusting rules .............................. 7
and H mixture needle ....................................... 7
2-3 Adjusting carburettor .................................. 8
Reference No.
I S S U E D :
1
2
page
21-21H-00
2 0 0 4 1 1

Advertisement

Table of Contents
loading

Related Manuals for Echo PB-2100

Summary of Contents for Echo PB-2100

  • Page 1: Table Of Contents

    1-6 Special tools ..........6 products information available at the time of publication. 2 EMISSION ADJUSTMENT GUIDE ....7 ECHO SERVICE MANUAL Ord. 403-11 2-1 General adjusting rules ......7 (Model : PB-2100, PB-2110, ES-2100, ES- 2-2 Presetting idle adjust screw, L mixture needle 2400) contains lots of information for servicing and H mixture needle ........

  • Page 2: Service Information

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 1 SERVICE INFORMATION 1-1 Specifications Model PB-2100 PB-2155 PB-2200SI Dimensions Length* mm(in) 220 (8.7) 250 (9.8) Width mm(in) 330 (13.0) Height mm(in) 340 (13.4) Dry weight** kg(lb) 4.0 (8.8) 4.1 (9.0) 4.3 (9.5) Engine Type KIORITZ, air-cooled, two-stroke, single cylinder Rotation Anticlockwise as viewed from the output end...

  • Page 3: Technical Data

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 1-2 Technical data Model PB-2100 PB-2155 PB-2200SI Engines Idling speed r/min 2400 - 3200 Wide open throttle speed* r/min 6800 - 7700 Compression pressure MPa (kgf/cm ) (psi) 0.83(8.4) 120 Ignition system Spark plug gap mm (in) 0.6 - 0.7 (0.024 - 0.028) Minimum secondary voltage at 1500 r/min...

  • Page 4: Torque Limits

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 1-3 Torque limits Descriptions Size kgf•cm N•m in•lbf Starter Pawl carrier 80 - 100 8 - 10 70 - 85 system Starter case M 4* 25 - 35 2.5 - 3.5 22 - 30 Ignition CDI module (Ignition coil) 35 - 50 3.5 - 5.0 30 - 45...

  • Page 5: Service Limits

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 1-5 Service Limits 5K193 5K228 5K229 5K230 5K231 5K016 5K042 5K194 5K171 Description A Cylinder bore When plating is worn and aluminium can be seen B Piston outer diameter Min. 32.13 (1.265) C Piston pin bore Max.

  • Page 6: Special Tools

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 1-6 Special tools a = 3 mm a = 4 mm Key Part Number Description Used for: 897801-33330 Tachometer PET-1000 Measuring engine speed to adjust carburettor 363018-00310 Washer Installing crankcase oil seal of starter side 433019-12330 Flange nut Removing magneto rotor (flywheel)

  • Page 7: Emission Adjustment Guide

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 2 EMISSION ADJUSTMENT GUIDE 2-1 General adjusting rules Before starting the unit for adjustment, check the following items. 1. The correct spark plug must be clean and properly gapped. 2. The air filter element must be clean and properly installed. 3.

  • Page 8: Adjusting Carburettor

    PB-2100 PB-2155 SERVICE INFORMATION PB-2200SI 2-3 Adjusting carburettor 1. Start engine and warm it up well for about 3 - 5 minutes with cycle of 50 seconds at WOT (Wide Open Throttle) and 10 seconds at idling. 2. Adjust H mixture needle to obtain maximum engine speed at WOT.

This manual is also suitable for:

Pb-2155Pb-2200si

Table of Contents