Advertisement
7. PASSWORD (CONT)
To enable the password function
1. Hold [
] button, red LED stays on, continue to hold, then press [
button once, then release both [
twice quickly.
2. Enter password, i.e. factory default for TC-318-14 is [2525], or the
current password.
3. Press [
] button, the red LED flashes twice.
You have now enabled the password function.
Pressing any single numeric button will not transmit any signal, the red
LED will blink once when a button is pressed, instead of flashing slowing
(signal transmission).
Operation with password function enabled
If the password function is enabled, before each operation, the password
must first be entered, followed by the [
Example, to turn on light 1 in Toggle On / Off mode, with password [2525]:
1. Enter [2525]
2. Press [
], red LED stays on.
3. Press 1 to turn light 1 on.
To disable the password function
1. Hold [
] button, then press [
and [
] buttons. Red LED flashes twice quickly.
2. Enter password, i.e. factory default for TC-318-14 is [2525] or the
current password.
3. Press [
] button, the red LED flashes twice.
You have now disabled the password function.
To change the password
1. Hold [
] button, then press [
and [
] buttons. Red LED flashes twice quickly.
3. Enter the current password, i.e. factory default for TC-318-14 is [2525].
4. Enter the new password, then press [
5. Enter the new password again, then press [
twice, you have changed the password successfully.
8. RESET REMOTE CONTROL
You may reset the remote control if you forget the password. After the
remote is reset, the unique remote ID will also be changed. Therefore,
it is required to program the remote again to all the receivers that you
have programmed before. Please follow the instructions below to reset
the remote.
1. Slide out the battery door;
2. Hold the "PROG" button on the back and slide back the battery door.
3. When the front LED flashes quickly, release the button.
4. The red LED will then flash 3 times slowly. This indicates the remote
has been reset. The password mode is now disabled and the password
has been reset to the factory default. You should now change the pass-
word and program the transmitter to all the receivers that you want to
control.
If you lost a remote, to ensure security and safety, you should erase all
remotes from all receivers and reprogram all existing remotes. Please
refer to the erasing method of each receiver.
] and [
] buttons. Red LED flashes
] button.
] button once, then release both [
] button once, then release both [
]
], red LED flashes
When the operating range is reduced, or when the red LED does not
flash during operation, it is time to replace the battery.
]
The transmitter is powered by a lithium battery CR-2032. Follow the
instructions below to replace the battery to the transmitter.
1. Slide out the battery door from the unit.
2. Remove the old battery.
Insert a new CR-2032 lithium battery
to the battery holder. Positive side
facing up.
3. Insert the battery door to the transmitter.
The red LED on the front of the unit will
be on for 1 second.
Insert battery
door with battery
]
Note: Dispose of old batteries promptly and properly.
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
]
of compliance could void the user's authority to operate the equipment.
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
12. CUSTOMER SERVICE
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user's instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
TM
The SkylinkHome System consists of many other devices such as
TM
SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z697
Patent Pending
©2010 SKYLINK GROUP
9. BATTERY
Slide out
battery door
+
+
CR2032
LED on for
1 second
10. FCC
11. WARRANTY
13. ACCESSORIES
TM
Battery door
with holder
Positive
side up
Advertisement
