Related Manuals for Century WDV10
Summary of Contents for Century WDV10
- Page 1 Operating Instructions MODELS: WDV10 WDV16 MODELS: T708 T716 T720TP Read ALL instructions before using the machine. 980198 98919 09/17/01 05/04...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. - Page 3 DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source. Disconnect the power supply before attempting any maintenance or service. WARNING: Operating a machine without observing all labels, decals, etc., could result in injury or damage.
- Page 4 120 Volt Machine Instructions For Connection To The Power Supply And The Electrical Ground This machine must be connected to the electrical ground to protect the operator from electric shock. The machine has an approved power cord with three conductors and a plug with three terminals. Connect the plug to a receptacle that has three holes and is connected to the electrical ground.
-
Page 5: Vacuum And Accessories
VACUUM AND ACCESSORIES Motor Block ATTENTION: The Polyester Filter must be cleaned after each use to maintain efficient suction. On/Off Switch Float: Keeps liquid out of Motor Block Polyester Filter: Remove for use with liquids IMPORTANT INSTRUCTIONS Hooks: Secure Motor Block to Tank Suction Inlet •... -
Page 6: Operation
OPERATION This machine is a commercial vacuum designed for wet and dry pick-up. Dry soil can be vacuumed directly into the tank. To empty the tank of dry soil, remove the top and dump into trash receptacle. For wet pick-up, remove polyester filter. The machine is equipped with a float shut-off. -
Page 7: Periodic Maintenance
PERIODIC MAINTENANCE (Every six to twelve months): Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning. Inspect gasket seals and replace those which have begun to leak. Replace both carbon brushes when either is Examine carbon motor brushes and commutator. -
Page 8: Carbon Brush Replacement
SERVICING THE VAC MOTOR CARBON BRUSH REPLACEMENT Disconnect power cord from power source. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the cover to one side. Remove the motor cover by removing two screws. - Page 9 Rivet, 5 x 24.5 S81847G6 Tank Clamp S81050 Screw, M5 x 35 S82846 Gasket S82585AG6BL Retainer, Tank Adapter S82608 Spring, Push Button S82593 Tank Deflector S82594BL Push Button, Two-Piece, Blue S82583AG6BL Hose Adapter, Blue S80558 Caster T9031 Label, Century 400...
- Page 10 WDV16 VACUUM MOTOR ASSEMBLY Part Num. Description Qty. S80466 Cord S80138 Strain Relief S80139 Bracket S81006 Screw, 5 x 20 S81054 Screw, 5 x 50 S86097AUG6 Handle, Gray S81979 Screw, 5 x 25 S81054 Screw, 5 x 50 S81005 Screw, 5 x 14 S80490 Terminal Block S81006...
- Page 11 Tie Rod, Plug S81860 Support S82764 Plug, Stopper S81302 Rivet, M5 x 19 S86250 Handgrip S82559 Wheel Caster S82594 Push Button, Two-Piece, Red S82680 Screw, M8 x 15 T9031 Decal, Century 400 S82556 Support, Axle S80904 Wheel S82557 Cap, End...
-
Page 12: Spare Parts
TSQ16 FRONT-MOUNTED SQUEEGEE Part Num. Description Qty. Part Num. Description Qty. BD705205 Hose Assembly BD735604 Blade End Screw, 10-32 x 1/2"L, SS BD715508 Housing BD735605 Blade End Screw Nut, 10-32, Nylock BD735608 Bolt, Guide Wheel, 1/4-20 x 1.75"L BD735603 Blade Attachment Screw, 10-32 x 5/8"L SS BD735607 Guide Wheel BD735612 Mounting Bolts, 1/4-20 x 3/4"L BD735611 Jam Nut, 1/4-20 serrated flanged... - Page 13 Century 400, Inc., 325 S. Price Road, Chandler, AZ 85224 USA Phone: (800) 752-1777 Fax: (480) 786-5724 © 2004 Century 400, Inc. All rights reserved. REVISED 05/01/04. T9033...