Confi Guring Home City Settings; Confi Guring Current Time And Date Settings Manually - Casio 5114 Operation Manual

Selecting a Mode
• The illustration below shows which buttons you need to press to navigate between modes.
• To return to the Timekeeping Mode from any other mode, hold down
• In any mode, press to illuminate the display.
Countdown Countdown
Timer Mode Timer Mode Stopwatch Mode Stopwatch Mode
World Time World Time
Alarm Mode Alarm Mode Mode Mode
E-24
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Auto Return Features
• The watch returns to the Timekeeping Mode automatically if you do not perform any button operation
for two or three minutes in the Data Recall, Alarm, Receive, or Hand Home Position Adjustment Mode.
• If you leave a screen with fl ashing digits on the digital display for two or three minutes without
performing any operation, the watch exits the setting screen automatically.
Initial Screens
When you enter the Data Recall, World Time, Alarm, Compass, or Barometer/Thermometer Mode, the
data you were viewing when you last exited the mode appears fi rst.
Scrolling
The and buttons are used to scroll through settings on the digital display while a setting screen is
displayed, and to move the hands of the watch manually. In most cases, holding down either of these
buttons will perform its operation at high speed.
E-26
Confi guring Home City Settings
There are two Home City settings: selecting the Home City, and specifying either standard time or daylight
saving time (DST).
To confi gure Home City settings
PM PM
indicator indicator
1. In the Timekeeping Mode, hold down
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
• For information about city codes, see the "City Code Table" at the
back of this manual.
2. To change the Home City code setting, press
hand clockwise.
• Keep pressing
Second Second
Hour : Hour :
hand hand you want to select as your Home City.
Minutes Minutes
City code City code • The current time in the time zone of the currently selected city code is
shown on the digital display.
DST indicator DST indicator
3. Press . This will display the DST setting screen on the digital
display.
4. Use to cycle through the DST settings as shown below.
Auto DST (AUTO)
E-28
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
DST indicator DST indicator
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Press . This will display the DST setting screen on the digital
display.
3. Use to cycle through the DST settings as shown below.
Auto DST (AUTO)
• The Auto DST ( AUTO ) setting can be selected only when a city code that supports time calibration
signal reception (page E-15) is selected. While Auto DST is selected, the DST setting changes
automatically in accordance with DST information included in the received time calibration signal.
4. After all the settings are the way you want, press
• The dSt indicator indicates that Daylight Saving Time is selected.
E-30
Operation Guide 5114 5214
for about two seconds.
Timekeeping Mode Timekeeping Mode
Data Recall Data Recall
Mode Mode
Hand Home Position Hand Home Position
Receive Mode Receive Mode Adjustment Mode Adjustment Mode
until each of the following
to move the second
until the second hand is pointing to the city code
DST off (OFF) DST on (On)
until each of the following
DST off (OFF) DST on (On)
to exit the setting screen.
• You can use buttons , , and to enter a sensor mode directly from the Timekeeping Mode or
from another sensor mode. To enter a sensor mode from the Data Recall, Stopwatch, Countdown
Timer, Alarm, World Time, Receive, or Hand Home Position Adjustment Mode, fi rst enter the
Timekeeping Mode and then press the applicable button.
• The hour and minute hands indicate the current time in all modes. In the Timekeeping, Data Recall,
Stopwatch, Countdown Timer, and Alarm modes, the second hand indicates the current (Timekeeping
Mode) second. The second hand performs other operations in the other modes.
Sensor Modes Sensor Modes
Compass Mode Compass Mode Thermometer Mode Thermometer Mode
Timekeeping
Use the Timekeeping Mode ( HOME) to set and view the current time and date.
• In the Timekeeping Mode, press to toggle the digital display between the day of the week and the
barometric pressure graph.
Day of the Week
Second
hand
Hour
hand
Minute
hand
Month Day Day of week
• The Auto DST ( AUTO ) setting will be available only when a city code that supports time calibration
signal reception (page E-15) is selected as the Home City. While Auto DST is selected, the DST
setting is changed automatically in accordance with time calibration signal data.
• Note that you cannot switch between standard time and daylight saving time (DST) while UTC is
selected as your Home City.
5. After all the settings are the way you want, press
• The hands of the watch will move the current time in the zone where the city code you selected as
your Home City is located. Do not perform any operation on the watch while the hands are moving.
• If Daylight Saving Time is selected, the dSt indicator will be on the digital display.
Note
• After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate the
current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping.
The reference point for UTC is Greenwich, England.
• Selecting some city codes automatically makes it possible for the watch to receive the time
calibration signal for the corresponding area. See page E-15 for details.
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time and date settings manually
1. In the Timekeeping Mode, hold down
PM PM
steps occurs.
indicator indicator Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Use to select the city code you want to select as your Home City.
• Each press of
until the second hand is pointed to the city code you want to
select.
• Select your Home City code before changing any other setting.
• For full information about city codes, see the "City Code Table" at the
Second Second
Hour : Hour : back of this manual.
Minutes Minutes hand hand
City code City code
Barometer/ Barometer/
Altimeter Mode Altimeter Mode
Barometric Pressure Graph
Barometric
Month Day
pressure graph
to return to the Timekeeping Mode.
until each of the following
moves the second hand clockwise. Keep pressing
E-25
E-27
E-29
E-31