Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for White 1919
Summary of Contents for White 1919
- Page 3 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using (this appliance). DANGER——To reduce the risk of electric shock: An appliance should never be left unattended when plugged in. Always unplug this appliance from the electric outlet immediately after using and before cleaning.
- Page 4 WARNING Keep fingers away from all moving parts. Special care is required around the sewing machine needle. 2. Always use the proper needle plate. The wrong plate can cause the needle to break. Do not use bent needles. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
- Page 8 _____________________ 2. ACCESSORIES tonhole foot Button sewing foot Ordinary needles 4 3 ocs Bat ooint needle (1 pc Zipper foot Screw dnvers Buttonhole cutter IsmallI a rqe Darning plate Oiler Bobbins Felts (2 pcs.) (3 pcs) Straight stitch foot %Olt hemming foot Quilting guide *ø—...
- Page 10 Connecting Foot Controller and Power Cord Connect foot controller power cord Before plugging in your machine, be sure that voltage is same as that of your machine. (written on a plate at back of machine> Specifications vary from country to country. Switch on, put power on the machine and turn on the sewing light.
- Page 11 The more you press foot con troher, the faster the machine runs. —6-—...
- Page 12 •...
- Page 16 Push bobbin to right and press down foot controller. automatically Machine stops when bobbin is full. Push bobbin to left, to disengage from wheel. bobbin, from Take spindle and cut thread. Retighten stop motion knob. bobbin is wound unevenly as shown, open face cover and trouble loosen set-screw of the guide for bobbin winding: Use screw driver...
- Page 20 Hold end of upper thread with left hand. Turn handwh eel slowly towards you until needle moves down and up again. Pull upper thread slowly and lower thread will be brought up in a loop. Pull out both threads to about 1 5 cm (6”) and place them together under presser foot on left.
- Page 24 Starting to Sew Place fabric under foot about 1 cm (04”) inside the edge. Lower presser foot lifter. Double Presser Foot Lifter In order to obtain larger openning when using very thick materials, firmly push presser foot lifter up as far as it will go. Reverse Sewing To reinforce seam, sew backwards to the edge of fabric by pushing down...
- Page 26 5. STRAIGHT SEWING 5, 6, 7, Set machine as shown. Option accessory. 3 kinds of straight stitch lengths can be selected as shown below. :$:_ Stitch Selector Stitch length No. 5 No. 6 No. 7 \— 6. ZIGZAG SEWING Set machine as shown. ZIGZAG PATTERN To prevent seam ends unravell ing.
- Page 34 10. SHELL STITCHJNG Silk, nylon organdy or similar sheer fabrics are suitable. Set machine as shown. Fold edge of material. With folded edge to left, place it under presser foot. Pull thread ends towards back when starting sewing. Make sure needle misses raw edge of fold when it moves side ways.
- Page 35 11. MENDING Patching (For model 1510. 1919 and 2640 only.) Set machine as shown. Place the patch over the worn part. Sew along the edge of the patch on the right side. Trim away the worn part close to the seam on back side.
- Page 36 12. STRETCH STITCHING The stitches shown are all used knit fabrics. with stretch These are special stitches built in the machine for your quick selection. Straight stretch Rickrack briar stretch Briar stretch Feather stretch Overcast stretch For model 1510, 1919 and 2640 only.) Adjusting Stretch Stitch Balance...
- Page 38 14.LAPPED SEAM SEWING (For model 1510, 1919 and 2640 only.) Set machine as shown. Place one piece of fabric over another according to the width of stitch size. For non-fray fabrics. (E For easy to fray fabrics. Sew over folded area from right side.
- Page 40 17. SEWING ON BUTTONS Set machine as shown, ZIGZAG PATTERN Attach darning plate on needle plate. (See page. 1 3) Select Zigzag width to suite the size of the button from pattern No. 8, 9, and 10. * No.11 for model 1510, 1919 and 2640 only.
- Page 42 19. ROLL HEMMING Set machine as shown, Option accessory. 5, 6, 7 With straight stitch _,.. %•• Make O.3cm(1/8”) double fold for about 5cm(2”) at very edge of material, and crease it. Sew twice at O.6cm(1/4”) from edge. Draw out work and leave about 1 Scm(6”) of thread.
- Page 43 •‘...
- Page 44 21. EMBROIDERY Set machine as shown. ZIGZAG PATTERN Remove foot, and holder screw. To avoid lower thread being pulled up, reduce upper thread tension. good embroidery, F— Needle Thread important to use correct needles and thread. No. 9 Use thin embroidery silk for 120—iCC...
- Page 48 it--- 2,c--...