Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for White-Westinghouse WW-6000
Summary of Contents for White-Westinghouse WW-6000
- Page 3 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using (this appliance). —To reduce the risk of electric shock: DANGER — An appliance should never be left unattended when plugged in. Always unplug this appliance from the electric outlet immediately after using and before cleaning.
-
Page 5: Table Of Contents
CONTE NTS 1. NAMES OF PARTS 2. PREPARATION FOR SEWING 2-1. Connecting Power Cord 2-2. Setting Telescopic Thread Stand 2-3. How to Change Threads 2-4. Replacing Needles 2-5. Threading 2-6. Preparation for Sewing and Checking 3. FOUR THREAD OVEREDGING STITCH USING 2 NEEDLES 3-1. -
Page 6: Names Of Parts
1. NAMES OF PARTS — Spool pin Presser foot lifter Pressure regulator screw Telescopic thread stand Thread take up lever fhread tension support Thread tension dials Front panel Differential feed dial 0 Side cover Stitch length adjuster Presser foot Bite width adjusting dial Upper knife Front cover Handwheel (Right side of machine) -
Page 7: Preparation For Sewing
will full —2—... -
Page 9: Replacing Needles
Cover the spool with the “NET” as chemical fibers (fibres) and the like are easily frayed. When using a real type thread spool, insert the spool adapter (supplied with the machine) (as shown). 2-4. Replacing Needles Replace needles in the following way: Note: be sure to take out the power supply plug before replacing needles. -
Page 12: Four Thread Overedging Stitch Using 2 Needles
3. FOUR THREAD OVEREDGING STITCH USING 2 NEEDLES 3-1. Before Sewing After threading is completed, and when the threads ire not wound around the stitch finger, gently draw out the four threads under and behind the presser foot, and turn the handwheel towards you oy hand two or three times to make the thread wind on to the needle plate. - Page 15 (3) I..Jribalanced lower looper tlread wraps Lower round and over the face Looper Wrong side Thread Tighten the thread tension of the lower looper ;he thread tension of the upper looper (Dial Right side Q sen Upper looper thread Left hand needle thread Tigen Right-hand needle thread (4) Unbalanced left needle thread too loose:...
-
Page 16: Adjustments For The Differential Feed
..:.:... -
Page 17: Adjustments For Size Of Bight
3-7. Adjustments for Size of Bight. • Adjust the size of the bight from 4.2mm (0.16”) to 6.0mm (0.23”) according to the kind of material. • The standard bight size is 4.5mm (0.17”) • Open the side cover to adjust the bight size. (1) If the cutting width is narrower than the bight size, turn the bite width adjusting dial to the direc tion of arrow. -
Page 25: Changing The Light Bulb
10. CHANGING THE LIGHT BULB When the light does not come on even though it is switched on: (1) Take Out the power supply plug. (2) Remove the lamp cover. (3) Change the light bulb. (4) Replace the lamp cover. 11. -
Page 26: Table Of Sewing Materials Needles And Thread
12. TABLE OF SEWING MATERIALS NEEDLES AND THREAD Thin material Medium to thick Thick material material (crepe, georgette) (thick denim) (Serge, gabardine, etc.) HAx1SP Needle HAx1T (705/1 30) (90) (80) (80) (90) (For home-use sewing machine) Polyestel (spun, filament) #60/2 Twisted thread #60/2 Twisted thread #50/2 Twisted thread #80/2 twisted thread... -
Page 27: Accessories
13. ACCESSORIES Needle plate for rolled hemming Presser foot for rolled hemming Screw drivers Needles Tweezers HAx1 SP HAx1 T #11.2 705/130 (80) Spool Adapter #14.. .3 (90) Oiler Cleaning brush Vinyl cover Accessor Waste tray Lower knife —22... -
Page 28: Specifications
14. SPECIFICATIONS 4 Threads (3 threads) Number of threads 2 Needles (1 needle) Number of needles Standard HAx1SP or HAx1T (705/130) #11 (80) Needles Width between two needles Overedge width Standard 4.5mm (Range 4.2 -.6mm) Size of bight 1 —5mm Stitch length Differential feed ratio 1:0.7—2...