Related Manuals for Zanussi ZGL 62 ITX
Summary of Contents for Zanussi ZGL 62 ITX
- Page 1 GAS HOB ZGL 62 ITX INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance...
-
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation This appliance must be installed and serviced by a Never leave the hob unattended when cooking with competent person as stated in the Gas Safety ( oil and fats. -
Page 3: Table Of Contents
Contents For the Installer For the User Instructions for the Installer Important Safety Information Installation Description of the Hob Electrical connections Operation Wiring Diagram Maintenance and Cleaning Fault Finding Something Not Working? Commissioning Service and Spare Parts Conversion from Natural Gas to LPG Guarantee/Customer Service European guarantee Environmental Information... -
Page 4: Description Of The Hob
Description of the Hob 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burners 4. Rapid Burner 5. Control knobs 6. Electric Ignition Push Button... -
Page 5: Operation
Operation Hob burners To light a burner: push the electric ignition pushbutton which is marked by a little spark. at the same time turn the relevant control knob anticlockwise to maximum position and keep it pushed down about 5 seconds. This will allow the "thermocouple"... -
Page 6: Maintenance And Cleaning
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up... -
Page 7: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. -
Page 8: Instructions For The Installer
Instructions for the Installer Engineers technical data Overall dimensions Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Width: 580 mm Depth: 500 mm Front Left Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Cut out dimensions Rear Right Burner (semi rapid) Width: 550 mm... -
Page 9: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current Edition) The hob may be located in a kitchen, a kitchen/diner or and the IEE Wiring Regulations (Current Edition). bed sitting room, but not in a bathroom, shower room or For appliances installed in the Republic of Ireland please garage. -
Page 10: Installation
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. -
Page 11: Building Over A Cupboard Or Drawer
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it It is also recommended to carry out the electrical will be necessary to fit a heat resistant board below the connection to the hob as shown in diagrams 1 and 2. -
Page 12: Electrical Connections
Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. -
Page 13: Wiring Diagram
Wiring Diagram A. TAPS IGNITOR SWITCHES B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check SOCKET PLUG (with cover removed) (face view) Earth Wire Green/Yellow Brown Blue START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity check. Blue Green Brown... - Page 14 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse Light burner manually replace if necessary Check by pass Check polarity and simmer earth continuity of supply point Check position of the Check earth continuity electrode of appliance...
-
Page 15: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 16: Service And Spare Parts
Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ·... -
Page 17: European Guarantee
European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: •... - Page 20 35687-8002 11/06...