Table of Contents
Advertisement
Quick Links
REMOTE KEYLESS ENTRY
INSTALLATION MANUAL
BEFORE INSTALLING THIS PRODUCT PLEASE READ
THIS INSTALLATION MANUAL THOROUGHLY!!
• This product must be installed by qualified per-
sonnel according to these instructions.
Items Included:
• Main unit
• Two 4-button remote transmitters
• Plug In LED
• Plug in program switch
• Main harness
• Owner's manual
Before you begin the installation:
• Verify with the customer the desired location
for the program switch and LED.
• Always use a multimeter when verifying vehicle
wiring.
Installation Notes:
•
Do not install the main unit in the engine com-
partment.
•
Make all wiring connections to the vehicle
before connecting the main 15-pin connector har-
ness to the main unit.
•
Mount the main unit in a secure area, away from
vehicle computers and heating/air conditioning
ducts.The location should be convenient for your
installation, but hidden from thieves. Mount the
unit as far away from metal objects as possible to
increase the range of the remote transmitters.
•
When running the harness wires through the
vehicle, be careful to run them where they cannot
be damaged or shorted. Keep them away from any
moving parts or areas of high heat. Use rubber or
plastic grommets to protect the harness wires
where they pass through holes in metal panels.
Main Harness:
• BLACK WIRE - Ground input (-). Connect to a
solid chassis ground that is clean and free of
paint or dirt.
• RED WIRE - +12V battery input.
• WHITE WIRE - Parking light output (+).
Connect to the wire that shows +12V when the
parking lights are turned on. If the vehicle's park-
ing light circuit exceeds 10A, a relay is required.
For vehicle's with independent left and right parking
light circuits, the parking light wires must be connect-
ed using diodes to keep the circuits separate.
• VIOLET WIRE - Unlock #87 normally open
input 10A fuse. (see Door Lock Wiring Diagrams)
• BLUE/BLACK WIRE - Unlock #30 common
output. (see Door Lock Wiring Diagrams)
• BROWN/BLACK WIRE - Unlock #87A normal-
ly closed input. (see Door Lock Wiring Diagrams)
• VIOLET/BLACK WIRE - Lock #87 normally
open input 10A fuse. (see Door Lock Wiring
Diagrams)
Advertisement
Table of Contents
Related Manuals for Black Widow Security BW 852
Summary of Contents for Black Widow Security BW 852
-
Page 1: Installation Notes
REMOTE KEYLESS ENTRY INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! • This product must be installed by qualified per- increase the range of the remote transmitters. sonnel according to these instructions. • When running the harness wires through the vehicle, be careful to run them where they cannot Items Included: be damaged or shorted. - Page 2 • GREEN/BLACK WIRE - Lock #30 common out- Adding or Deleting Remote Controls put. (see Door Lock Wiring Diagrams) When you enter the code learning mode, the sys- • WHITE/BLACK WIRE - Lock #87A normally tem will learn new remotes and automatically closed input.
-
Page 3: Default Reset
Remote Programmable Features: Step Function Button 1 (Default) Button 2 Ignition Controlled Door Locks Door Unlock Pulse Single Double Arming Mode Standard Silent Door Lock Pulse Length .75 Seconds 3 Seconds Passive Starter Defeat Enable Ignition Trigger Feature Remote Programmable Features Button 2 = Silent Program #4: Door Lock Pulse Length... -
Page 4: Troubleshooting
TROUBLESHOOTING Problem Probable Cause Suggested Correction Unit will not go into Code RED or YELLOW wire not con- RED wire should connect direct- Learning Mode. nected to the correct power ly to the battery. Connect YEL- source. Code Learning sequence LOW wire to true ignition wire performed too slowly. - Page 5 KEYLESS ENTRY WIRING DIAGRAM BLACK GROUND +12V 15A FUSE WHITE PARKING LIGHT OUTPUT (+) 10A FUSE VIOLET #87 N.O. UNLOCK INPUT 10A FUSE BLUE/BLACK #30 COMMON UNLOCK OUTPUT BROWN/BLACK #87A N.C. UNLOCK OUTPUT VIOLET/BLACK #87 N.O. LOCK INPUT 10A FUSE GREEN/BLACK #30 COMMON LOCK OUTPUT RECEIVER...
-
Page 6: Door Lock Wiring Diagrams
DOOR LOCK WIRING DIAGRAMS NEGATIVE PULSE DOOR LOCK SYSTEM POSITIVE PULSE DOOR LOCK SYSTEM (+) DOOR LOCK (-) DOOR LOCK FACTORY FACTORY FACTORY FACTORY DOOR LOCK DOOR LOCK DOOR LOCK DOOR LOCK (+) DOOR UNLOCK (-) DOOR UNLOCK SWITCH RELAYS SWITCH RELAYS VIOLET... - Page 7 OPTIONAL TWO-STEP UNLOCK WIRING DIAGRAMS TWO-STEP UNLOCK TWO-STEP UNLOCK NEGATIVE PULSE POSITIVE PULSE CONNECT (-) DOOR LOCK (+) DOOR LOCK TO +12V (-) DOOR UNLOCK (+) DOOR UNLOCK BLUE/WHITE BLUE/WHITE LOCK/UNLOCK LOCK/UNLOCK SWITCH SWITCH CONNECT FACTORY DOOR TO +12V FACTORY DOOR LOCK MODULE LOCK MODULE VIOLET...
- Page 8 RELAY WIRING DIAGRAMS STARTER DEFEAT TRUNK RELEASE DIAGRAM TO TRUNK RELEASE WIRE CONNECT TO +12V GRAY IGNITION WIRE ORANGE SWITCH WIRE CONNECT TO +12V STARTER DOME LIGHT DIAGRAM TO NEGATIVE DOME LIGHT WIRE TO POSITIVE DOME LIGHT WIRE CONNECT BLACK/YELLOW BLACK/YELLOW TO +12V WIRE...