Advertisement
Quick Links
I N S T A L L A T I O N
I N S T A L L A T I O N
BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM
• DO read through this installation manual.
• DO NOT install the control module in an engine compartment.
• The alarm may arm itself when power is first connected.This is a normal condition.
ITEMS SUPPLIED WITH THE STARTER DISABLE/KEYLESS ENTRY SYSTEM
• Receiver and control module
• Two 2-Button or 3-button, code learning
transmitters
• Door lock harness
OPTIONAL ACCESSORIES
Backup battery...............................................BWS-500
Remote starter ..............................................RAS-101
Trunk release .....................................................TR-100
Starter disable relay socket.........................BRS-003
(+) door lock Inverter..............................BW-34516
SPECIFICATIONS
Operating voltage..................+12 VDC Neg. Ground
Code learning..........................................3 Codes Max.
Current consumption............5 mA (max) disarmed.
Door lock/unlock output .........................(-) 500 mA.
Channel 2 output drive.............(-) 500 mA variable.
M A N U A L
M A N U A L
STARTER
DISABLE/
KEYLESS
ENTRY
SYSTEM
• Valet/override switch
• LED status indicator
• Wiring harness, fuseholder, & fuse
Window roll up...........................................................WRM-2
Power door lock.........................................................PDL-50
Relay ....................................................................................SPDT
5-wire door lock relay & socket ...............BRS-008P16
Remote control transmit frequency.......................310 mHz.
Passive arming delay..................................30 Seconds approx.
Auxiliary output drive ...............................250 mA maximum.
Flashing output drive .................................(-) 250 mA 30 sec.
Dome light output......................................(-) 250 mA 30 sec.
Advertisement
Related Manuals for Black Widow Security BW 752
Summary of Contents for Black Widow Security BW 752
- Page 1 I N S T A L L A T I O N M A N U A L I N S T A L L A T I O N M A N U A L STARTER DISABLE/ KEYLESS ENTRY SYSTEM BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM •...
-
Page 2: Installation Instructions
- 1 - INSTALLATION INSTRUCTIONS IMPORTANT: Make all wiring connections to the vehicle before connecting the main 6-pin harness and all plug-in connectors to the receiver control module. 1. Before mounting the Control Module, you must set the PROGRAMMING DIPSWITCHES for the kind of operation the customer wants. -
Page 3: Led Status
- 2 - 11. Connect the Main 6-Pin Wiring Harness and all pin connectors to the Control Module. Install the fuse in the RED wire of the main wiring harness. 13. Code Learning Procedure: To add a new remote to the system, turn ignition key ON, OFF, ON, OFF, and leave on (3 times). Siren/Horn will chirp once. - Page 4 - 3 - CONNECTOR PIN NUMBERS AND WIRE COLOR CODES 6 PIN HARNESS Wire Color Function Main Power hook to constant 12v+ source Brown Negative Output for siren or car horn Yellow Ignition Input 12v+ (must not drop out while starting) Black Ground...
-
Page 5: Wiring Diagram
- 4 - WIRING DIAGRAM LOCK (-) PULSE GREEN +12V CONSTANT OUTPUT UNLOCK (-) PULSE BLUE 1 2 3 4 DIPSWITCH (INSIDE OF MODULE) FUSE (+)12V BROWN HORN/SIREN (-) OUTPUT YELLOW 12V IGNITION RECEIVER BLACK GROUND GRAY MODULE 2nd CHANNEL (-) OUTPUT (REQUIRES RELAY) WHITE PARKING LIGHT (-)OUTPUT (REQUIRES RELAY) STARTER DISABLE INPUT/OUTPUTS... -
Page 6: Power Door Lock Diagrams
- 5 - POWER DOOR LOCK POSITIVE TRIGGER DOOR LOCK CIRCUIT*: DIAGRAMS: TO DOOR LOCK RELAY TO DOOR UNLOCK RELAY The Starter Disable/Keyless Entry LOCK UNLOCK comes equipped to handle ground door lock installations.The Blue and GREEN WIRE BLUE WIRE Green wires from the Receiver FROM ALARM FROM ALARM... - Page 7 PROBABLE SUGGESTED SYMPTOM CAUSE CORRECTION Keyless will not go RED or YELLOW wire not connected RED wire should connect directly to into Code Learning to the correct power source. Code the battery. Connect YELLOW wire to Mode Learning sequence done to slow. true ignition wire (Not at Fuse Block).