Advertisement
Quick Links
Universal Quick Install Guide
Quantum and Triton Boards
Use this guide to install Quantum boards and Triton class telephony boards,
including Triton VoIP, Triton Analog Extension, Triton Analog Trunk (LS and LS/
GS), Triton Resource, Triton T1/PRI, and Triton T1/E1 PRI, which are all different
boards with common installation procedures.
MVIP BUS Termination Switch
All Triton PCI Family and Quantum Boards
Note:
In systems with over 12 boards installed, use the 10-connector side of the
ribbon cable on the short end and use the 12-connector side of the ribbon
cable on the long end. Starting with the innermost connectors, connect the
boards, leaving a minimum of 3 connectors hanging off each end.
Supported Board/Software Guidelines
Board
Quantum
Triton Analog Extension
Triton Analog Extension B
Triton Analog Trunk-12
Triton Analog Trunk-8
Triton T1/PRI
Triton T1/E1 PRI
Triton VoIP-30
Triton VoIP-8
Triton Resource
MVIP Connector
Board Silhouette
OE
OE
OE
4.0A
4.0i
4.5
Yes
No
Yes
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Power Cable
OE/ACC/
OE/ACC/
ACM/HPBX
ACM 5.0/
4.6
5.0A
Yes
Yes
Yes
Yes
No
No
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
OE/ACC/ACM/
OE/ACC/ACM/
HPBX 5.0A
HPBX 5.0A
Update 2 & 3
Update 4 & up
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Advertisement
Related Manuals for Altigen Quantum Boards
Summary of Contents for Altigen Quantum Boards
- Page 1 Universal Quick Install Guide Quantum and Triton Boards Use this guide to install Quantum boards and Triton class telephony boards, including Triton VoIP, Triton Analog Extension, Triton Analog Trunk (LS and LS/ GS), Triton Resource, Triton T1/PRI, and Triton T1/E1 PRI, which are all different boards with common installation procedures.
-
Page 2: Installation Notes
Installation Notes • Observe proper board handling procedures (refer to AltiGen Field Alert #67). • Pre-installation of boards is recommended over on-site installations. • Although boards are factory tested prior to shipping, it is recommended that you follow a burn-in period of approximately 12 hours minimum before an on-site deployment. -
Page 3: Connection Options
Connection Options There are 3 connection options for connecting Quantum/Triton boards to trunks and extensions: 1. 12 Ports Bridging Adapter 2. 66 Punch Down Block with 50-Pin Telco Female Connector 3. Patch Panel with 50-Pin Telco Female Connector... -
Page 4: Installation Instructions
Installation Instructions (It is assumed that the server operating system, AltiWare and its corresponding licenses are already installed.) 1. Ensure that the chassis power switch is in the OFF position and the power cord is unplugged before removing the chassis cover. 2. - Page 5 13.If the MVIP test fails, check MVIP connections and troubleshoot accordingly. If there are any failures, note the board(s) and use the following steps to troubleshoot the MVIP connection: (System shutdown is not necessary for MVIP troubleshooting unless replacing a board.) •...
-
Page 6: Technical Support
Technical Support End users Contact your authorized AltiGen Dealer. Authorized AltiGen Dealers Call AltiGen Technical Support at 510-252-9712 Submit a case on the authorized dealer web site: https://dealer.altigen.com The following information will be required: Dealer Name - ID# __________________________________________________ End User Name ____________________________________________________ Location __________________________________________________________ Credit Card (if required) __________________________ Expiration___________ Serial #____________________________________________________...