Table of Contents
Advertisement
•
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard
t a n d a r d I D E
disk drives to these connectors. If you intend to create a Serial ATA
RAID set using these connectors, set the C o n f i g u r e S A T A A s
item in the BIOS to [RAID]. See section "4.3.5 IDE Configuration" on
page 4-16 for details.
•
For RAID 5, use at least three hard disk drives. For RAID 10, use at
least four hard disk drives. Use two to four hard disk drives for each
RAID 0 or RAID 1 set.
P5LD2-V SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1/RAID 5/ RAID 10) is available only
when you are using Windows
When using the connectors in S S S S S t a n d a r d I D E
•
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
S e r i a l A T A h a r d d i s k d r i v e c o n n e c t i o n
S e r i a l A T A h a r d d i s k d r i v e c o n n e c t i o n
S e r i a l A T A h a r d d i s k d r i v e c o n n e c t i o n
S e r i a l A T A h a r d d i s k d r i v e c o n n e c t i o n
S e r i a l A T A h a r d d i s k d r i v e c o n n e c t i o n
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 1 / S A T A 2
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
S A T A 3 / S A T A 4
A S U S P 5 L D 2 - V
A S U S P 5 L D 2 - V
A S U S P 5 L D 2 - V
A S U S P 5 L D 2 - V
A S U S P 5 L D 2 - V
S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E mode by default. In
SATA4
SATA3
®
SATA1
®
2000 Service Pack 4 or the Windows
®
2000/XP/2003 Server.
t a n d a r d I D E
t a n d a r d I D E
t a n d a r d I D E mode, connect the
t a n d a r d I D E
C o l o r
C o l o r
C o l o r
C o l o r
C o l o r
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
R e d
R e d
M a s t e r
M a s t e r
R e d
R e d
R e d
M a s t e r
M a s t e r
M a s t e r
B l a c k
B l a c k
B l a c k
B l a c k
B l a c k
S l a v e
S l a v e
S l a v e
S l a v e
S l a v e
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
SATA2
®
XP
U s e
U s e
U s e
U s e
U s e
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
2 - 2 7
2 - 2 7
2 - 2 7
2 - 2 7
2 - 2 7
Advertisement
Table of Contents
