Page 1 ® TeemTalk for Windows CE & XPe User's Guide...
Page 2 Neoware, Inc. 3200 Horizon Drive King of Prussia, PA 19406 Tel: +1-610-277-8300 Fax: +1-610-771-4200 Email: info@neoware.com Neoware UK Ltd The Stables, Cosgrove Milton Keynes MK19 7JJ Tel: +44 (0) 1908 267111 Fax: +44 (0) 1908 267112 Email: teem-info@neoware.com...
Page 3: Software Support
TeemTalk Software Support Telephone: +1-610-277-8300 Web: http://www.neoware.com/support/ Software Version 5.0.1 October 2004 Neoware UK Ltd, The Stables, Cosgrove, Milton Keynes, MK19 7JJ Tel: +44 (0) 1908 267111 Fax: +44 (0) 1908 267112 TeemTalk © 1988-2004 Neoware UK Ltd, All Rights Reserved. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
Page 4 The material in this manual is for information purposes only and is subject to change without notice. Neoware UK Ltd accepts no responsibility for any errors contained herein. Trademarks TeemTalk is a registered trademark of Neoware UK Ltd. ADDS Viewpoint A2 is a trademark of Applied Digital Data Systems Inc. AIX is a registered trademark of International Business Machines Corporation.
Page 5: Table Of Contents
Contents Contents Introduction ............1-1 About This User's Guide ............... 1-1 Terms & Conventions ..............1-3 Getting Started..........2-1 WBT Session Configuration ............2-1 Using The Connection Wizard ............2-1 Terminal Emulation Configuration ........... 2-4 Emulation Options ..............2-4 Graphics Mode ................2-6 DEC Suite Options ..............
Page 6 Contents Session Management (Windows XPe) ......... 2-39 Logged On As System Administrator ..........2-39 Logged On As A User ..............2-39 TeemTalk for Windows CE Display ..........2-41 Setup Menus (Windows CE) ............2-41 The Button Tools (Windows CE) ........... 2-42 The Soft Buttons (Windows CE) ............
Page 7 Contents Redefining The Toolbar..............5-3 Adding Buttons .................. 5-3 Adding A Space Between Buttons ............ 5-4 Removing A Button Or Space ............5-4 Saving The Button Tools ..............5-4 Assigning User-Defined Functions ........... 5-5 Setup Menus ............. 6-1 Displaying & Closing Menus ............6-1 Using The Menus ................
Page 8 Contents Auxport Setup .................. 6-74 Terminal Settings ................6-75 Tab Stops ..................6-82 Local Editing ................... 6-83 Block Transmission ................. 6-85 Tek 4014 Settings ................6-89 GIN Mouse Definitions ..............6-91 Attributes ..................6-92 Define Keyboard Macros ..............6-97 Defining A Key Or Key Combination ........6-98 Specifying Characters ...............
Page 9 Contents DG 410/412 Emulation ........9-1 Session Configuration ..............9-1 WBT Mode ..................9-1 Non-WBT Mode ................9-2 Keyboard Mapping ................ 9-3 Key Functions ..................9-3 Key Codes ..................9-5 HP 700-92/96 Emulation ......... 10-1 Session Configuration ..............10-1 WBT Mode ..................10-1 Non-WBT Mode ................
Page 10 Contents Playback Keystrokes ..............11-13 Editing Macros ................11-13 Error Codes ..................11-14 Notice Board Facility ..............11-15 Introduction ................... 11-15 Key Functions ................11-15 Copying Screen Data To The Display .......... 11-15 Copying Screen Data To A Function Key ........11-16 IBM 5250 Emulation ........
Page 11 Contents Non-WBT Mode ................14-2 Keyboard Mapping ..............14-3 PT250 Emulation ..........15-1 Session Configuration ..............15-1 WBT Mode ..................15-1 Non-WBT Mode ................15-2 The Status Line ................15-3 Keyboard Mapping ..............15-5 Displaying Alternate Characters ..........15-7 Siemens 97801 Emulation ......16-1 Session Configuration ..............
Page 12 Contents Non-WBT Mode ................19-2 Display Format ................19-4 Status Line Messages ..............19-4 Keyboard Mapping ..............19-5 Initialization Commands ........ 20-1 Introduction ................. 20-1 Command Summary ..............20-2 Host Connection ................20-5 Session Configuration ..............20-7 Display..................20-9 Keyboard & Mouse ..............20-20 Auxiliary Port ................
Page 13: Introduction
Introduction Introduction This chapter introduces the contents of this User's Guide. About This User's Guide This User's Guide describes how to use TeemTalk version 5.0 for Windows CE and XPe. Most of the functionality is the same for both Windows CE and XPe versions, but where there are differences, the text will indicate them.
Page 14: Virtual Key Names
Introduction Chapter 7: DEC VT Emulations Describes features of the DEC VT emulations. Chapter 8: BQ 3107 Emulation Describes features of the Bull BQ 3107 emulation. Chapter 9: DG 410/412 Emulation Describes features of the Data General D410/412 emulation. Chapter 10: HP700-92/96 Emulation Describes features of the Hewlett Packard HP700/92 emulation.
Page 15: Host Command Summary
Introduction Appendix C: Host Command Summary Lists the host commands that are supported in each terminal emula- tion mode. Appendix D: Product Specification Describes the level of support provided by each terminal emulation. Terms & Conventions This User's Guide uses the following terms and conventions. 1.
Page 16 Introduction Notes...
Page 17: Getting Started
Getting Started Getting Started This chapter describes how to configure a session and describes various display features. WBT Session Configuration Using The Connection Wizard This section describes the basic procedure for creating a session configuration in WBT mode. The options available are described in detail in the following sections. 1.
Page 18 Getting Started 4. Enter a name which will identify this session configuration for future selection in the Connection Name box. 5. Select the terminal emulation required in the Emulation list box. 6. If additional configuration options are displayed, make the relevant selections. Refer to the Terminal Emulation Configuration section later in this chapter for details.
Page 19 Getting Started The optional SSL (Secure Sockets Layer) protocol enables authenticated and encrypted communication between clients and servers. Refer to the SSL Connec- tion section later in this chapter for details. The optional SSH (Secure Shell) client/server protocol is used to encrypt and transmit data securely over a network, with authentication (proof of client identity) provided by a password and/or key.
Page 20: Terminal Emulation Configuration
Getting Started Terminal Emulation Configuration Emulation Options The Emulation options in the Connection Wizard Connection Information dialog box are as follows: The ADDS A2 emulation provides compatibility with software designed to drive the ADDS Viewpoint A2 terminal, as emulated by the Wyse WY-50/50+/60 terminals. Refer to the Wyse Emulations chapter for details.
Page 21 Getting Started The IBM 5250 emulation provides compatibility with software designed to drive IBM 5250 type alphanumeric terminals. This emulation can be used for connection to an IBM AS/400, System/36 or System/38. Note that the initial display will be an ASCII text screen known as Network Virtual Terminal mode (NVT mode for short).
Page 22: Graphics Mode
Getting Started When VT500 7-Bit is selected, all 8-bit codes are converted to their 7-bit equivalents, whereas VT500 8-Bit leaves 8-bit codes unchanged. If you are using VT200 applications, select VT500 7-Bit. Refer to the DEC VT Emulations chapter for details. The VT+HP220 emulation is based on the VT500 terminal series and includes the HP function keys F1 - F8 (not user programmable).
Page 23: Bq 3107 Option
Getting Started The High Function Terminal option is displayed when the AIXTerm emulation is selected. This enables you to switch between HFT (High Function Terminal) mode (default) and VT100 mode. BQ 3107 Option The VIP Mode option enables you to set the VIP mode to 7700 or 7760. HP 700-92/96 Option The HP Model option specifies what is reported back to the host in response to a terminal identification request.
Page 24: Ibm 5250 Options
Getting Started The setting of the Right Ctrl acts as Enter Key option determines whether or not the right Control key performs the same function as the keypad Enter key. IBM 5250 Options The IBM 5250 Model option specifies what is reported back to the host in response to a terminal identification request.
Page 25: Tcp/Ip Connection Settings
Getting Started TCP/IP Connection Settings The TCP/IP Telnet Configuration dialog box can be displayed from the Connection Wizard Host Information dialog box by setting the Connection Type to TCP/IP then clicking the Advanced button, or the New Connection dialog box when in non- WBT mode by selecting TCP/IP in the Type list box then clicking the Configure button.
Page 26: Host Connection
Getting Started Connection Timeout (Secs:) This enables you to specify how many seconds the emulator has to attempt to make a host connection before it either attempts to connect to the next host (if Host Rollover is specified in the Host Connection dialog box) or it issues a Connection Failed mes- sage.
Page 27: Tn3270 Options
Getting Started Send Location This enables you to enter the location of this terminal which may be used by the host to provide a list of users currently logged in giving their name and location. TN3270 Options This dialog box is displayed by clicking the 3270 Options button in the TCP/IP Telnet Configuration dialog box when TN3270 is not suppressed.
Page 28 Getting Started power off, so the first connection of any given power on may not be TEST1. Assume that the start point is random. Note: There are separate counters for the IBM 3270 and IBM 5250 emulations. When you achieve a TN3270E connection, the LU device name that you are connected as will be displayed on the status line.
Page 29: Tn5250 Options
Getting Started TN5250 Options This dialog box is displayed by clicking the 5250 Options button in the TCP/IP Telnet Configuration dialog box when TN5250 is not suppressed and the IBM 5250 Model is not set to 3812-1 or 5553-B01 (printers). Refer to the next section for 5250 Printer Options.
Page 30 Getting Started case TEST1, TEST2, ... may all be tried in one connection until the host accepts one, or all possibilities have been tried. In the latter case the same name is sent twice in succession to indicate to the host all names have been tried. If concurrent 5250 sessions are started before a previous session has negotiated an acceptable device name, it is possible that the two sessions will access the counter simultaneously and not all possible names will be tried by each session.
Page 31 Getting Started 5250 Printer Options This dialog box is displayed by clicking the 5250 Options button in the TCP/IP Telnet Configuration dialog box when TN5250 is not suppressed and the IBM 5250 Model is set to 3812-1 (a printer). Device Name Specifies the name of the printer device.
Page 32 Getting Started *IBM47121 *IBM47122 *IBM47221 *IBM47222 *IBM4770 *IBM5152 *IBM5201 *IBM5202 *IBM5204 *IBM5216 *IBM6404 *IBM6404EP *IBM6408 *IBM6408EP *IBM6412 *IBM6412EP *HPII *HPIID *HPIIP *HPIII *HPIIID *HPIIIP *HPIIISI *HP4 *HP310 *HP500 *HP520 *HP550C *HP560C *HPPAINT *CPQPM15 *CPQPM20 *EPAP2250 *EPAP3250 *EPAP5000 *EPAP5500 *EPDFX5000 *EPDFX8000 *EPFX850 *EPFX870 *EPFX1170 *EPLX810...
Page 33 Getting Started *LEGL Legal-sized paper (8.5 x 14 inches). *EXEC Executive-sized paper (7.25 x 10.5 inches). A4-sized paper (210 mm x 297 mm). A5-sized paper (148 mm x 210 mm). B5-sized paper (182 mm x 257 mm). *C80 Continuous-form paper, 8.0 inches wide (Paper Source 1 only).
Page 34: Ssl Connection Settings
Getting Started SSL Connection Settings The optional SSL (Secure Sockets Layer) protocol enables authenticated and encrypted communication between clients and servers. Before anyone can connect to a server the system administrator must make available a copy of the root certificate used to sign the server’s identity certificate and the number of the telnet port the server is listening on (the default for secure telnet is 992).
Page 35: Notes About Certificates
Getting Started 7. You may optionally enter your Password for the client certificate here too. If you check Save this password will be stored, encrypted, along with the certificate itself. Please note this is a security risk as anyone who can acquire a copy of your registry will be able to use your certificate.
Page 36: Storage Of Certificates
Getting Started 3. CA (Certificate Authority) or root certificates. These are used to authenticate the other two types. The client will need to store these locally. Storage of Certificates TeemTalk stores its certificates in the Registry as binary values. The following keys are used: HKEY_CURRENT_USER\Software\Neoware\Security\SSL\CA Certificates HKEY_CURRENT_USER\Software\Neoware\Security\SSL\Client Certificates...
Page 37: Ssh Connection Settings
Getting Started SSH Connection Settings The optional SSH (Secure Shell) client/server protocol is used to encrypt and transmit data securely over a network, with authentication (proof of client identity) provided by a password and/or key. To enable an SSH connection, select the SSH option in the Connection Wizard Host Information dialog box or, when running TeemTalk, in the New Connection dialog box Type list box.
Page 38 Getting Started SSH Connection to an openSSH Server using a Key File 1. Select the SSH option in the Connection Wizard Host Information dialog box, or from the New Connection dialog Type list box when running TeemTalk. 2. Display the Telnet Options dialog box and change the Port Number to the host's SSH port (22 is the default for SSH) then click OK.
Page 39 Getting Started 6. Enter a Filename. This is the name the key will be stored under in the registry and the name displayed in the Keyfile drop down list in the previous dialog box. 7. Select the type of key you wish to create. openSSH servers support both DSA and RSA keys.
Page 40 Getting Started 12. To make use of your key you need to copy it on to the server. 13. Select all in the text box and then copy to put the key into the Windows clipboard. 14. Logon to your server using username and password. 15.
Page 41: Ssh Key File Permissions
Getting Started SSH Connection to an SSH Communications Security Tectia Server using a Key File 1. Follow the instructions in the previous section for using a keyfile with openSSH up to and including step 12. 2. If they do not already exist you need to create a directory ~/.ssh2 and a text file within it called authorization.
Page 42: Non-Wbt Mode
Getting Started Modem Connection Settings The Modem Settings dialog box can be displayed from the Connection Wizard Host Information dialog box by setting the Connection Type to Modem then clicking the Advanced button, or the New Connection dialog box when in non-WBT mode by selecting Modem in the Type list box then clicking the Configure button.
Page 43: Serial Connection Settings
Getting Started Serial Connection Settings The Serial Configuration dialog box can be displayed from the Connection Wizard Host Information dialog box by setting the Connection Type to Serial then clicking the Advanced button, or the New Connection dialog box when in non-WBT mode by selecting Serial in the Type list box then clicking the Configure button.
Page 44 Getting Started Data Bits Factory default: 8 This option specifies the number of data bits sent for each transmitted character. Stop Bits Factory default: 1 This specifies the number of stop bits sent for each transmitted character. Transmit Rate Factory default: Unlimited The setting of this option determines the maximum effective baud rate that the emulatortransmits terminal reports and data sent as a result of pasting data to the host.
Page 45: Automate Login Process
Getting Started Automate Login Process The Automate Login Process dialog box enables you to automate part or all of the host login procedure. The settings in this dialog box enable you to specify what is sent to the host in response to prompts displayed on the screen.
Page 46 Getting Started The list of predefined commands that can be inserted include UserName (indi- cated by <UN>) and Password (indicated by <PW>). Selecting either of these will cause a dialog box to pop-up when logging on to the host prompting the user to enter a name or password, respectively.
Page 47: Printer Port Settings
Getting Started Printer Port Settings The Printer Port Settings dialog box provides several print options. The options available depend on whether you are running TeemTalk for Windows CE or XPe. TeemTalk for Windows CE TeemTalk for Windows XPe 2-31...
Page 48 Getting Started CE - Direct Print Data To The Print Manager The Current System Printer Driver box displays the name of the currently selected system printer when both the Use Network Printer (LPR) and Print Direct To Port options are not selected. Clicking the Configure button will display a Print Manager dialog box which enables you to specify printer settings.
Page 49 Getting Started Direct Print Data To A Specific Port To direct print data to a specific port, select Print Direct To Port and specify the Printer Port. Selecting the FormFeed Terminator option will cause the printer to advance the paper to the top of the form when it has finished printing. The Output Character Set option enables you to specify the character set used for printing when Print Direct To Port is selected.
Page 50 Getting Started CE - Direct Print Data To A Network Printer To direct print data to a printer on the network when running Windows CE, select Use Network Printer (LPR) and enter the LPD Hostname. Clicking the Configure button will display a dialog box which enables you to specify various print settings. You must specify the Printer Name.
Page 51 Getting Started XPe - Direct Print Data To A Network Printer To direct print data to a printer on the network when running Windows XPe, select Use Network Printer (LPR) and enter the LPD Hostname. Clicking the Configure button will display a dialog box which enables you to specify various print settings. You must specify the Printer Name.
Page 52: Gui Overrides
Getting Started GUI Overrides The GUI Overrides dialog box enables you to disable various GUI items and also enables you to specify how the emulator responds when the host closes the connection. Clicking the Disable Elements button will display another dialog box enabling you to disable any of the command bar elements.
Page 53 Getting Started Selecting Reconnect will cause the emulator to attempt to reconnect to the host. By default, a warning message will be displayed if you attempt to exit the emulator while a host connection is still active. You can disable this message by selecting the No connection warning on close option.
Page 54: Aux Port Settings
Getting Started Aux Port Settings The Aux Port Settings dialog box enables you to specify a COM or LPT port for bidirectional output when in any DEC VT mode, ANSI BBS, Sco Console, HP 700- 92/96 or IBM 3151 mode. The Functionality options enable you to set the auxiliary port as bidirectional and specify that it is to be opened at start-up.
Page 55: Session Management (Windows Xpe)
Getting Started Session Management (Windows XPe) The way that TeemTalk for Windows XPe sessions are created or modified depends on whether you are logged on as a system administrator, or as a user without administrative privileges. Logged On As System Administrator If you are logged on as a system administrator, you can either create a unique session only for your own use, or you can create session templates that are available to all users of the system.
Page 56 Getting Started When you load a template, modify the settings then save the session, a local copy of the template will be made with the same name, but with the changed settings. This copy will replace the template in the list of session configurations displayed in the Open Session dialog box.
Page 57: Teemtalk For Windows Ce Display
Getting Started TeemTalk for Windows CE Display The TeemTalk for Windows CE command bar provides access to a series of menus and buttons that enable you to configure the terminal emulator and perform various functions. Note: The buttons available depend on whether or not you are in WBT mode.
Page 58: The Button Tools (Windows Ce)
Getting Started The Button Tools (Windows CE) The TeemTalk for Windows CE button tools provide a quick way of actioning commands or displaying setup dialog boxes by just clicking a button. Displays the New Connection dialog box for making a serial or network host connection.
Page 59: The Soft Buttons (Windows Ce)
Getting Started The Soft Buttons (Windows CE) A set of soft buttons are provided which can be programmed so that they perform various functions when clicked. You can toggle between command bar and soft button display either by clicking the following buttons: or by pressing the keys Ctrl + Alt + Left Cursor or Ctrl + Alt + Right Cursor.
Page 60: Teemtalk For Windows Xpe Display
Getting Started TeemTalk for Windows XPe Display The Menu Bar (Windows XPe) The TeemTalk for Windows XPe menu bar provides access to three menus that enable you to perform various functions and configure TeemTalk for compatibility with the application. Note: The options available in the menus depend on your version of TeemTalk.
Page 61: The Toolbar (Windows Xpe)
Getting Started The Toolbar (Windows XPe) A toolbar is displayed below the TeemTalk for Windows XPe menu bar. This displays a series of buttons which provide a quick way of actioning commands or displaying setup dialog boxes when clicked. You can redefine all the buttons and add or remove buttons from the toolbar using the Button Tools dialog box.
Page 62: The Status Bar
Getting Started The Status Bar Along the bottom of the display is a status bar which shows the status of various operations and enables you to switch between modes. The information displayed in the status bar depends on the current terminal emulation. The following description applies when running any of the DEC VT terminal emulations, though some of the fields and buttons will be applicable to other emulations as well.
Page 63: Hotspots
Getting Started Not Ready signifies that the printer is not ready to receive data for printing. Ready signifies that the printer is ready to receive data for printing. Auto signifies that the emulation is in Auto Print mode in which the current cursor line is sent to the printer when a command for the cursor to move to the next line is issued.
Page 64: At&T 4410 Emulation
Getting Started AT&T 4410 Emulation When running the AT&T 4410 emulation the display size is 80 (or 132) columns by 25 lines with a scroll region of 24 lines. A row of function buttons is displayed along the bottom of the window. These correspond to the function keys F1 through F8 on the keyboard.
Page 65: Viewdata Mode
Getting Started Viewdata Mode You can select one of three display formats for viewdata mode: 40 column, 80 column, or Split Screen. Selecting Viewdata 40 or 80 mode will enable a single viewdata page of 40 or 80 columns wide by 24 lines deep to be displayed. Viewdata Split enables simultaneous display of two pages side by side, each page consisting of 24 lines and 40 columns.
Page 66 Getting Started Notes 2-50...
Page 67: Keyboard Configuration
Keyboard Configuration Keyboard Configuration This chapter describes how to configure the keyboard, define key functions and compose special characters. Keyboard Mapping The keyboard is mapped as close as possible to the terminal being emulated. An llustration showing the mapping of key functions on the 101/102 key Enhanced AT style keyboard layout is shown in each terminal emulation chapter.
Page 68: Defining A Key Or Key Combination
Keyboard Configuration This enables you to redefine the function of most of the keys on your keyboard, including the key combinations listed below: Alt + Key Shift + Key Alt + Shift + Key Control + Key Alt + Control + Key Control + Shift + Key Alt + Control + Shift + Key Each definition may contain a string of up to 127 characters.
Page 69: Key Combinations & Sequences
Keyboard Configuration Key Combinations & Sequences You can program a key to perform the function of a combination or sequence of keys. For example, you can cause the F1 key to perform the same function as pressing the keys Alt + F4 together, or pressing the keys F2 then F3 then F4. Keys are identified by their virtual key names as listed in the Virtual Key Names appendix.
Page 70: Compose Character Sequences
Keyboard Configuration Compose Character Sequences Compose character sequences can be used to generate codes for characters not shown on your keyboard. The characters that can be composed depend on the setting of the Character Set Mode option in the Emulation Settings dialog box and the Preferred Char.
Page 71 Keyboard Configuration The following tables use several conventions: The keys bearing the characters used to compose a special character may be pressed in any order unless (in order) is specified. (DEC Multinat.) indicates that the character can only be composed if the Character Set Mode option in the Emulation Settings dialog box is set to Multinational, and the Preferred Char.
Page 72 Keyboard Configuration COMPOSE CHARACTER SEQUENCES feminine ordinal " ª ¨ space quotation mark indicator double open « < < number sign angle brackets (Multinational) ° ' space apostrophe degree sign ° space (National) plus or ± commercial at minus sign (Multinational) superscript 2 (National)
Page 73 Keyboard Configuration COMPOSE CHARACTER SEQUENCES (continued) Û Ä A " ¨ A A umlaut U circumflex ° Ü Å U " ¨ U A ring U umlaut (degree sign) Y umlaut Ÿ Æ Y " ¨ Y A E diphthong (DEC Multinat.) (in order) German small...
Page 74 Keyboard Configuration COMPOSE CHARACTER SEQUENCES (continued) soft (syllable) ó — o acute hyphen (Latin-1) registered trade- ô o circumflex mark (Latin-1) macron õ – o tilde (Latin-1) three quarters ö o " ¨ o o umlaut (Latin-1) (in order) division sign o e diphthong œ...
Page 75: Mouse Functions
Mouse Functions Mouse Functions This chapter describes the special functions assigned to the mouse and how to redefine them. Introduction You can assign up to six special functions to the left and right mouse buttons when used in conjunction with modifier keys. The following functions are defined by default: Left Button Right Button...
Page 76: Selecting & Copying Text
Mouse Functions This enables you to specify the functions of the left and right mouse buttons when clicked on their own or in conjunction with modifier keys. You can assign up to six functions to each button, either entering your own definition in the same format as described for keyboard macros and soft buttons, or selecting from a list of standard built-in functions.
Page 77: Send Keyword
Mouse Functions Send Keyword The Send Keyword function enables you to click on any delimited word displayed on the screen and it will be sent to the host, as long as the word is not already defined as a hotspot. Keyword delimiters are space, NULL, / , : = ( ) [ and ]. Show &...
Page 78 Mouse Functions Notes...
Page 79: The Toolbar
The Toolbar The Toolbar This chapter describes how to use and redefine the TeemTalk for Windows XPe toolbar. Using The Toolbar The TeemTalk for Windows XPe toolbar provides a quick way of actioning commands or displaying setup dialog boxes by just clicking a button. You can customize the toolbar by adding or removing buttons to suit your requirements using the Button Tools dialog box, which is displayed from the Settings menu.
Page 80 The Toolbar Copies selected data to the clipboard. Pastes clipboard data at the current cursor position. Displays the Printer Setup dialog box. This enables you to select any printer that is configured in Microsoft Windows. Will produce a hardcopy of screen data. Displays the Attributes dialog box.
Page 81: Redefining The Toolbar
The Toolbar Redefining The Toolbar Selecting Button Tools from the Settings menu will display a dialog box that enables you to redefine the toolbar. The Current Tool box displays the toolbar button and its function that is currently selected for editing, or located where a new button is to be inserted to its left in the toolbar.
Page 82: Adding A Space Between Buttons
The Toolbar 5. Specify the command to be performed when this button is clicked either by selecting from the Commands list or by typing your own definition in the Current Tool text box. 6. Click the Insert at Current button. 7.
Page 83: Assigning User-Defined Functions
The Toolbar Assigning User-Defined Functions You can enter a definition of your own in the Current Tool text box. The definition can contain key functions and control characters to be actioned as well as normal text. Specifying Key Functions You can cause a key function to be actioned by including the virtual key name of the key enclosed by the <...
Page 84 The Toolbar Notes...
Page 85: Setup Menus
Setup Menus Setup Menus This chapter describes the options available in the setup menus and dialog boxes. Displaying & Closing Menus The following menus can be displayed from the command bar: Note: The options available in the menus depend on whether or not you are in WBT mode.
Page 86: Using The Menus
Setup Menus To close a menu: Mouse: Click anywhere outside the menu. Keyboard: Press the Alt key. Using The Menus The menu options follow several conventions: Options that are displayed dimmed are not applicable to the current mode of operation and cannot be selected.
Page 87: Dialog Boxes
Setup Menus Dialog Boxes Selecting an option which is followed by an ellipsis (...) will cause a dialog box to be displayed. The example shown below is displayed by selecting the Block Transmission... option in the Settings menu. There are four basic methods for changing settings within the dialog boxes. Options preceded by a check box, such as Send Unprotected Only in the example above, are true or selected when the box contains a ✔, and false or unselected when the box is empty.
Page 88: Default Settings
Setup Menus To select a dialog box option: Mouse: Click the check box, button or list box. The current setting is highlighted or surrounded by a dotted rectangle, or both. Keyboard: Move to the option to be changed either by holding down the Alt key and pressing the key bearing the character underlined in the option, if one is displayed, or press the Tab key to move forward through the options (left to right, top to bottom), or Shift + Tab to move backwards,...
Page 89: Creating A Connection Template (Ce)
Setup Menus The following 'backslash' values can be used: \u Unicode introducer \r Carriage return \n Line feed \e Escape Note that as the \ and ^ characters are used as value introducers, to enter these as character values you need to precede them with a backslash character, i.e. enter \ as \\ and ^ as \^.
Page 90: Selecting A Connection Template (Ce)
Setup Menus Selecting A Connection Template (CE) The Open Session dialog box enables you to select a connection template to use when the terminal is not in WBT mode. This is displayed by selecting Open Session... in the File menu. The Description list box displays the names of connection templates that were created using the Save Session As dialog box.
Page 91: Save Using New Session Name
Setup Menus Save Using New Session Name If TeemTalk for Windows XPe was started without a session (i.e. not started by clicking on a desktop icon or by selecting a session from the Start menu), you can save the session configuration under a new name: 1.
Page 92 Setup Menus The Defined Sessions list box displays one-line descriptions of session configurations that were created using the TeemTalk Connection Wizard or the Save Session As dialog box when running TeemTalk. The session configuration currently loaded is highlighted. Clicking on a defined session then the OK button will cause TeemTalk to load that session configuration.
Page 93: Menu Descriptions
Setup Menus Menu Descriptions The following pages describe the options available in all the menus and associated dialog boxes. The descriptions begin by showing the menu or dialog box as it is displayed on the screen. The factory default setting is shown below each option title where applicable.
Page 94: New Connection
Setup Menus New Connection... (Not available in WBT mode) Factory default: Serial, Com 1 This will display a dialog box that enables you to make a host connection. The Type list box specifies the type of host connection that is to be made. The Connect To box specifies the port or host to communicate with.
Page 95 Setup Menus Making A Network Host Connection To connect to a network host node, select TCP/IP in the Type list box. The Connect To box will display the available devices on the network. Select the name of the device required or enter the host name or IP address. If the session was created using the Connection Wizard and the Host Rollover On Connection Fail option was selected, you can specify up to three more hosts in the boxes below.
Page 96: Open Session
Setup Menus Making An SSL Or SSH Host Connection (if supported) The optional SSL (Secure Sockets Layer) protocol enables authenticated and encrypted communication between clients and servers. Refer to the SSL Connection section in the Getting Started chapter for details. The optional SSH (Secure Shell) client/server protocol is used to encrypt and transmit data securely over a network, with authentication (proof of client identity) provided by a password and/or key.
Page 97: Save Session
Setup Menus The Defined Sessions list box displays one-line descriptions of session configurations that were created using the TeemTalk Connection Wizard or the Save Session As dialog box when running TeemTalk. The session configuration currently loaded is highlighted. Clicking on a defined session then the OK button will cause TeemTalk to load that session configuration.
Page 98: Save Session As
Setup Menus Save Session As... (Not available in WBT mode) TeemTalk for Windows CE This will display a dialog box that enables you to save the current session configuration as a connection template. You can create multiple connection templates, any one of which can be selected for use.
Page 99: Startup Options
Setup Menus 3. Click the OK button to save the session. If you specified a session name that already exists, a message box will ask you to confirm whether you want to overwrite the existing session name with the new settings. Startup Options...
Page 100 Setup Menus TeemTalk for Windows CE TeemTalk for Windows XPe 6-16...
Page 101 Setup Menus You can direct print data to a printer handled by the Print Manager, a specific port, or a network printer. CE - Direct Print Data To The Print Manager When running TeemTalk for Windows CE, the Current System Printer Driver box displays the name of the currently selected system printer when both the Use Network Printer (LPR) and Print Direct To Port options are not selected.
Page 102: Direct Print Data To A Specific Port
Setup Menus Direct Print Data To A Specific Port To direct print data to a specific port, select Print Direct To Port and specify the Printer Port. Selecting the FormFeed Terminator option will cause the printer to advance the paper to the top of the form when it has finished printing. The Output Character Set option enables you to specify the character set used for printing when Print Direct To Port is selected.
Page 103 Setup Menus CE - Direct Print Data To A Network Printer To direct print data to a printer on the network when running TeemTalk for Windows CE, select Use Network Printer (LPR) and enter the LPD Hostname. Clicking the Setup button will display a dialog box that enables you to specify various print settings.
Page 104 Setup Menus XPe - Direct Print Data To A Network Printer To direct print data to a printer on the network when running TeemTalk for Windows XPe, select Use Network Printer (LPR) and enter the LPD Hostname. Clicking the Setup button will display an LPD Device Settings dialog box that enables you to specify various print settings.
Page 105 Setup Menus Print Screen This enables you to produce a hardcopy of data displayed on the screen. The Print Screen dialog box will be displayed when a printer handled by the Print Manager is selected in the Printer Setup dialog box. The Text option is selected by default and the printer resolution and scaling options are not accessible.
Page 106 Setup Menus reversed, with colour converted to monochrome, or colour converted to monochrome with black and white reversed. Once a screen print is initiated by clicking OK, another dialog box will be displayed while the screen data is being spooled out to the print manager. This enables you to terminate the print process before data is actually printed.
Page 107: Edit Menu
Setup Menus Edit Menu Clipboard Text Clipboard Graphics Selecting one of these options will enable selected text or graphics to be copied to the clipboard when the Copy command is used. The Paste and Select All commands will also be enabled. A tick will be displayed next to the option when it is selected. Copy The Copy commands become available when data has been selected.
Page 108: Settings Menu
Setup Menus Settings Menu The English, French and German options enable you to select the language that will be used in all menus and dialog boxes. The following dialog boxes can be displayed from this menu. Note that the dialog boxes used to configure specific emulations can only be displayed when the relevant emulation is running.
Page 109: Auxport Settings
Setup Menus Unisys T27 Settings - for configuring the Unisys T27 emulation. BQ 3107 Settings - for configuring the Bull BQ 3107 emulation. Serial Settings - for specifying serial communication settings. Auxport Settings - for specifying auxilliary port settings. Terminal Settings - for specifying terminal and display settings.
Page 110: Emulation Settings
Setup Menus Emulation Settings This dialog box is displayed by selecting Emulation in the Settings menu. Alpha Emulation (Not available in WBT mode) The setting of this option determines the current alpha emulation mode. The ADDS A2 emulation provides compatibility with software designed to drive the ADDS Viewpoint A2 terminal, as emulated by the Wyse WY-50/50+/60 terminals.
Page 111 Setup Menus The DG 410/412 emulation provides compatibility with software designed to drive the Data General D410 and D412 terminals. Refer to the DG 410/412 Emulation chapter for details. The HP 700-92/96 emulation provides compatibility with software designed to drive the Hewlett Packard 700/92, 2392A, 2622A, 70094 and 70096 terminals.
Page 112 Setup Menus emulated by the Wyse WY-50/50+/60 terminals. Refer to the Wyse Emulations chapter for details. The TVI 950 and TVI 955 emulations provide compatibility with software designed to drive the TeleVideo 950 and 955 terminals, respectively. The Unisys T27 emulation provides compatibility with software designed to drive the Unisys T27 terminal.
Page 113 Setup Menus AT 386 or Sco Console emulations. The setting determines the graphics mode that will be entered when the host sends graphics commands. The ReGIS emulation enables you to run applications written for the DEC VT340 terminal in ReGIS mode. The Tek4014 emulation enables you to run applications written for the Tektronix 4010 and 4014 terminals.
Page 114: Hp 700-92/96 Settings
Setup Menus HP 700-92/96 Settings This dialog box is displayed by selecting HP 700-92/96 in the Settings menu. Local Echo Factory default: Unselected The setting of this option determines whether keyboard entered characters are displayed on the screen as well as sent to the host. When unselected, characters are not displayed when they are transmitted to the host unless the host 'echoes' them back.
Page 115 Setup Menus SPOW (B) Factory default: Unselected The setting of the SPace OverWrite option determines whether or not keyboard entered spaces overwrite existing characters. When unselected, keyboard entered spaces will overwrite existing characters. Selecting this option will cause the SPOW latch to be enabled. The latch can then be activated by a carriage return.
Page 116 Setup Menus The type of handshake used for block transfers is determined by the type of block transfer to be performed, the mode that the HP70092 emulation currently operating in (character, block line, block page, or modify mode), and the setting of these two options.
Page 117 Setup Menus Display Form Feeds Factory default: Selected When selected, this will cause form feeds to be represented on the display as characters. Ignore Form Feeds Factory default: Unselected When the emulator receives a form feed command from the host it normally results in a line feed on the display in HP 700/92 mode.
Page 118 Setup Menus FldSeparator Factory default: ^_ (i.e. US) This text box is used to specify the ASCII character used to indicate the end of each protected field (except the last) that is sent in Edit Mode. To change the current definition, delete the definition displayed in the text box and type in the new one, either as the control key character equivalent or the decimal value of the ASCII character.
Page 119 Setup Menus Pages Factory default: 4 In HP 700-92/96 mode the display area is 80 or 132 columns by 24 lines with 168 lines stored off-screen, giving a total display memory of 192 lines. This option enables you to specify whether display memory is divided into 2, 4, 6 or 8 pages. Typeahead Enabled Factory default: Unselected When the emulator is connected to an HP 3000, you normally have to wait for the host...
Page 120: Pt250 Settings
Setup Menus PT250 Settings This dialog box is displayed by selecting PT 250 in the Settings menu. Screen Format Factory default: 80 x 24 The setting of this option determines the display memory format, the number of lines and columns that are displayed, and the amount of data transmitted to the host when the emulation is in Block mode (as determined by the setting of the Block Mode option in this dialog box).
Page 121 Setup Menus Line Block Mode Factory default: Unselected The setting of this option determines how much data is transmitted when the emulation is in Block mode and the Enter key is pressed. When unselected, the contents of the screen (page) will be sent to the host. When selected, the contents of the current cursor line will be sent.
Page 122 Setup Menus Received LF is CR/LF Factory default: Unselected The setting of this option determines how the emulation interprets received line feed characters. Selecting it will cause a carriage return command to be appended to every line feed command received. Received CR is CR/LF Factory default: Unselected The setting of this option determines how the emulation interprets received carriage...
Page 123: Ibm 3151 Settings
Setup Menus IBM 3151 Settings This dialog box is displayed by selecting IBM 3151 in the Settings menu. Operating Mode Factory default: Echo The setting of this option determines how keyboard entered data is sent to the host and displayed on the screen. In Echo mode, keyboard entered data is sent only to the host.
Page 124 Setup Menus Note that the contents of the display will be cleared when you change the display format. Turnaround Char Factory default: CR This option specifies the line turnaround character (LTC) that is generated when a Read command is received or one of the block data transmission keys is pressed. Note that selecting DC3 will disable the XON/XOFF inbound and outbound pacing characters.
Page 125 Setup Menus When set to Column, tab stops are provided by column-tab definitions. Field attribute characters are ignored. Enter Key Factory default: Return This option enables you to specify whether the Enter key performs the same function as the Return key or the Send key. Return Key Factory default: Field This option specifies whether or not the cursor can enter a line within a protected field...
Page 126 Setup Menus Auto LF Factory default: Unselected The setting of this option in conjunction with that of the Auto New Line option determines the destination of the cursor when the Return key is pressed or the CR character is received. When both this and the Auto New Line options are unselected, the cursor will move to the first position of the current line when the Return key is pressed or the CR character is received.
Page 127: Wyse Settings
Setup Menus Wyse Settings This dialog box is displayed by selecting Wyse in the Settings menu. Note that some of the settings apply to the TVI 910+, TVI 920, TVI 925, ADDS A2 and HZ 1500 emulations in addition to the Wyse emulations. Also, some settings may not apply to the particular Wyse emulation currently running.
Page 128 Setup Menus Page Size Factory default: 1 x Lines This option applies to the WY-50+ and WY-60 emulations and specifies the size of a page in display memory in multiples of the Lines setting. Note that the other emulations only support 1 x Lines. The 1 + Rest setting will divide the display memory into two pages, the first containing the number of lines specified by the Lines option, the second containing all the remaining lines.
Page 129 Setup Menus ASCII Font Factory default: WY ASCII This option determines whether the Wyse ASCII or PC standard character set is used as the first half of the multinational character set when in multinational mode (as set by the Character Set Mode option in the Emulation Settings dialog box). WPRT Attribute Factory default: Dim This option applies to all emulations and enables you to specify the appearance of...
Page 130 Setup Menus Auto Page Factory default: Unselected This option applies to the WY-50+, WY-60 and all the TVI emulations. It determines what happens when the cursor reaches the top or bottom of the page. When unselected, the cursor either moves to the top of the same page or data scrolls up from the bottom, as determined by the setting of the Auto Scroll option.
Page 131 Setup Menus Send ACK Factory default: Selected This option applies to all emulations and specifies whether or not an ASCII ACK character is sent to the host port after certain commands have been executed. Block Mode Factory default: Unselected This option applies to all emulations. In Block mode, keyboard entered data is displayed and processed locally, allowing you to edit it before a block of data is sent to the host.
Page 132: Ta6530 Settings
Setup Menus TA6530 Settings This dialog box is displayed by selecting TA 6530 in the Settings menu. Power On Mode Factory default: Conversational This option determines the operating mode that is in effect when the TA6530 emulation is entered. Note: Changing the current setting will not take effect until you re- load the emulation, so you will need to save the new setting before exiting the emulation.
Page 133 Setup Menus Return Function Factory default: Unselected This option specifies whether or not the function of the Enter key is defined by the application when in Block mode. When selected, the key is regarded as an application specific function key. Normally this should be unselected. Bell On Factory default: Selected This option enables or disables an audible tone which is heard when the emulation...
Page 134: Ibm 3270 Settings
Setup Menus IBM 3270 Settings This dialog box is displayed by selecting IBM 3270 in the Settings menu. IBM 3270 Model Factory default: 3278-2-E This specifies what is reported back to the host in response to a terminal identification request. (Note that not all features of the specified terminal may be supported.) TN3287 printing is supported by selecting 3287-1.
Page 135 Setup Menus Numeral Swap Factory default: Unselected When using a code page that supports a bilingual keyboard, this will cause all numbers to be displayed using the National character set when in Latin mode. Symbol Swap Factory default: Unselected Selecting this option will cause symbols such as brackets to be displayed the correct way round when typing in right-to-left mode.
Page 136 Setup Menus Selecting End on Non-Hex enables you to specify the number of characters that make up the end sequence in the End Length box. The bypass will then terminate as soon as a non-hexadecimal character is received (any character except in the range 0 through 9 and A through F) followed by the end sequence.
Page 137 Setup Menus Default Language, Codepage & Character Set Settings Language Type Codepage Char Set CCSID English (US) SBCS English (UK) SBCS Belgian SBCS Canadian French SBCS Danish SBCS Finnish SBCS German SBCS Dutch SBCS Italian SBCS Swiss French SBCS Swiss German SBCS Swedish SBCS...
Page 138: Notice Board Setup
Setup Menus Notice Board Setup This dialog box is displayed by clicking the Notice Board Setup button in the IBM 3270 Settings dialog box, or by pressing the keys Alt + F2. Refer to the Notice Board Facility section in the IBM 3270 Emulation chapter for information on how to use the Notice Board.
Page 139 Setup Menus Copy Only User Fields to F-Key Factory default: Selected This will enable only data contained in user entry fields in the selected area to be copied to a function key. Refer to the Copying Screen Data To A Function Key section in the IBM 3270 Emulation chapter for details.
Page 140: Ibm 5250 Settings
Setup Menus IBM 5250 Settings This dialog box is displayed by selecting IBM 5250 in the Settings menu. IBM 5250 Model Factory default: 3179_2 This specifies what is reported back to the host in response to a terminal identification request. (Note that not all features of the specified terminal may be supported.) The terminal models and their display characteristics are listed below: Model Display...
Page 141 Setup Menus 5555_B01 Monochrome 24 x 80 5555_C01 Colour 24 x 80 The printer models are listed below: 3812-1 Single byte printer 5553-B01 Double byte printer If double byte character sets are supported, then select either 5555_B01 (monochrome) or 5555_C01 (colour) for display, or 5553-B01 for printing. Keyboard Type The settings of the Keyboard Type and National Character Settings options below will reflect the default settings for the chosen language and should only be changed by...
Page 142: National Character Settings
Setup Menus Telnet Options Clicking the Telnet Options button will display a dialog box with additional options. These are described in the Getting Started chapter. Monochrome Factory default: Depends on terminal type By default the setting of this option will match the normal display characteristic of the IBM 5250 Model selected, as shown in the list above.
Page 143 Setup Menus There are separate entries for the Single Byte Character Set (SBCS) and, if supported, Double Byte Character Set (DBCS). These should only be changed by the System Administrator. If they have been changed and you wish to restore the default settings, click the Default button in the IBM 5250 Settings dialog box.
Page 144 Setup Menus Default Language, Character Set & Codepage Settings SBCS DBCS Language KBDTYPE CHARSET CODEPAGE CODEPAGE English (US) English (UK) Belgian Canadian French Danish Finnish German Dutch Italian Swiss French Swiss German Swedish Norwegian French Spanish Portuguese Japanese Kanji + Katakana 1172 Korean 1173...
Page 145: Unisys T27 Settings
Setup Menus Unisys T27 Settings This dialog box is displayed by selecting Unisys T27 in the Settings menu. General Settings Protocol Factory default: None This can be set to None, Poll/Select or Point to Point. Selecting Poll/Select will enable up to three environments. Only one environment can be enabled when Point to Point is selected.
Page 146 Setup Menus Group Select Character Factory default: ^D This specifies a single character address so that the host can simultaneously transmit to all terminals with that address. Address Factory default: ^D’ This enables you to specify a two-character group poll address that enables the host to simultaneously poll all terminals with that address.
Page 147: Environments Settings
Setup Menus Use optional poll/select characters Factory default: Unselected Specifies whether the optional poll select sequence, 7B 7C hex, is to be used instead of the standard sequence 70 71 hex (default). Environments Settings Lines per page Factory default: 24 This specifies the number of lines allocated to each logical page of data in the range 1 to 256.
Page 148 Setup Menus Address Factory default: ^D’ The address can be any two characters, except NUL and SYNC, that uniquely identify a T27 environment in a host network. Factory default: ENVMNT 1 This enables you to specify a name, up to eight characters long, which will be displayed on the screen to identify the current environment.
Page 149 Setup Menus Cursor is hidden Factory default: Unselected The cursor can be displayed or hidden, depending on the setting of this option. Cursor is static Factory default: Selected The cursor can be displayed as static or blinking, depending on the setting of this option.
Page 150 Setup Menus Display HT when tabbing from host Factory default: Unselected When this option is selected, an HT character is displayed when a tab character is received in a message from the host. Display HT when tabbing from keyboard Factory default: Unselected When this option is selected, an HT character is displayed when the Tab key is pressed.
Page 151 Setup Menus Lines are double height Factory default: Unselected This determines whether each line is single-height (normal) or double-height. Lower case lockout Factory default: Unselected When selected, this will cause the LOCK key to be on so that only UPPERCASE characters can be generated.
Page 152: Tab Settings
Setup Menus displays all subsequent characters from the extended character set until an ESC SI sequence is received to switch back to the normal character set. The Unisys T27 emulation transmits an ESC SO sequence when it encounters extended characters in its display buffer and an ESC SI when standard characters are to be sent.
Page 153: Bq 3107 Settings
Setup Menus BQ 3107 Settings This dialog box is displayed by selecting BQ 3107 in the Settings menu. Operating Mode Factory default: Block In Block mode, keyboard entered data is displayed and processed locally, allowing you to edit it before a block of data is sent to the host. In Character mode, keyboard entered data is sent simultaneously to the host and the display.
Page 154 Setup Menus Message Row Factory default: At Row 25 The setting of this option determines whether the message row (Partition 0) is at the top or bottom of the display. Blink Displayed As Factory default: Caret In VIP mode the start of a flashing field can be indicated by a caret or space character. Blank Displayed As Factory default: Tilde In VIP mode the start of a blank field can be indicated by a tilde or space character.
Page 155 Setup Menus The T (Type) box entry determines what happens to the programmed contents of an FKC key when pressed. This can have the value 0, 1 or 2. When set to 0, the contents of the Message box will be sent to the host. When set to 1, the contents of the Message box together with text that can be transmitted from the screen will be sent to the host.
Page 156: Serial Settings
Setup Menus Serial Settings When the terminal is not in WBT mode, this dialog box is displayed by selecting Serial in the Settings menu, or by clicking the Configure... button in the New Connection dialog box when the connection type is set to Serial. Note that the port for serial communications is selected via the New Connection dialog box which is displayed from the File menu.
Page 157 Setup Menus In/Out - XON/XOFF on transmitted & received data Hardware - DTR/CTS hardware flow control. Data Bits Factory default: 8 This option specifies the number of data bits sent for each transmitted character. Stop Bits Factory default: 1 This specifies the number of stop bits sent for each transmitted character. Transmit Rate Factory default: Unlimited The setting of this option determines the maximum effective baud rate that the...
Page 158: Auxport Setup
Setup Menus Auxport Setup This dialog box is displayed by selecting Auxport in the Settings menu. It enables you to specify a COM or LPT port for bidirectional output when in any DEC VT mode, ANSI BBS, Sco Console, HP 700/92 or IBM 3151 mode. The Functionality options enable you to set the auxiliary port as bidirectional and specify that it is to be opened at start-up.
Page 159: Terminal Settings
Setup Menus Terminal Settings This dialog box is displayed by selecting Terminal in the Settings menu. Note: The Tab Stops dialog box displayed by clicking the Set Tabs button is described in the next section. Display Rows Factory default: 24 This specifies the number of text rows that can be viewed in the workspace at any one time out of the total number stored in memory.
Page 160 Setup Menus Memory Rows Factory default: 144 This option determines the number of text rows that are stored in memory. This can be set from 0 to 528 rows by default. The Display Rows option specifies the number of memory rows that can be viewed in the workspace at any one time. Memory Page Size Factory default: 24 When the emulator is in VT420 mode, the display memory of 144 lines can be divided...
Page 161: Preferred Font
Setup Menus Keyboard Type Factory default: 101\102 (Windows XPe only) This TeemTalk for Windows XPe option enables driver-less support for a 122 or 108- key keyboard instead of the standard 101\102-key keyboard. Preferred Font This enables you to specify the font to be used for displaying characters. The available settings depend on the fonts installed.
Page 162 Setup Menus When PC Hebrew 862 is selected, the following key functions will be enabled: Ctrl + Alt + F1 Select Multinational 8-bit mode and left-to-right typing. Ctrl + Alt + F2 Select National 7-bit mode (lowercase English characters will be displayed as Hebrew) and right-to-left typing.
Page 163 Setup Menus is automatically displayed. When unselected, the display remains unchanged and the cursor moves off-screen to the relevant page stored in memory. Auto Wrap Factory default: Unselected The setting of this option determines whether characters wrap to the next line when the right margin is reached.
Page 164: Cursor Moves Right To Left
Setup Menus Display Error Codes Factory default: Selected This option determines whether or not a chequerboard symbol is displayed when the delete code is received. Jump Scroll Factory default: Unselected The setting of this option determines whether data is scrolled one or several lines at a time when the window becomes full.
Page 165: Auto Resize
Setup Menus Keyboard Sends Scan Codes Factory default: Unselected This applies to the DEC VT520, VT PC-Term and Wyse PC-Term emulations. It determines whether keyboard scan codes or ASCII codes are sent to the host on key press/release. Note that this cannot be selected at the same time as the Keyboard Sends Position Codes option.
Page 166: Tab Stops
Setup Menus Tab Stops This dialog box is displayed by clicking the Set Tabs button in the Terminal Settings or Wyse Settings dialog box. Tab stops can be set for the DEC VT, ANSI and SCO Console emulations using the Tab Stops dialog box displayed from the Terminal Settings dialog box, and for the Wyse emulations by using the Tab Stops dialog box displayed from the Wyse Settings dialog box.
Page 167: Local Editing
Setup Menus Local Editing This dialog box is displayed by selecting Local Editing in the Settings menu. Edit Operation Factory default: Unavailable The setting of this option determines whether Local Editing mode can be selected and how editing is performed. Selecting Unavailable will prevent you or the host from entering Edit mode.
Page 168 Setup Menus Attributes Cleared Factory default: Unselected The setting of this option determines the effect of an erase command on character attributes. When selected, both attributes and characters will be cleared from display memory when an erase command is issued. When this option is unselected, all video attributes currently used will remain in display memory when an erase command is issued.
Page 169: Block Transmission
Setup Menus Block Transmission This dialog box is displayed by selecting Block Transmission in the Settings menu. The options in this dialog box only apply to the block mode functionality supported by the DEC 'VT' terminal emulations. The block mode settings that are supported by other terminal emulations are specified in their respective dialog boxes.
Page 170 Setup Menus Send All Selected Areas Factory default: Selected When the Send Only Selected Characters option is selected, the setting of this option determines whether all selected areas on a page are sent to the host when the Enter key is pressed, or only the area containing the cursor.
Page 171 Setup Menus Send Partial Page Factory default: Unselected The setting of this option determines whether a partial page or data in the scrolling region is sent to the host when the Enter key is pressed and the Line Transmission On option is unselected. When selected, this option will enable a partial page to be sent to the host.
Page 172 Setup Menus End of Line Characters Factory default: ^M (i.e. CR) This text box is used to specify the characters that are to indicate the end of a line in a data block. To change the current definition, delete the definition displayed in the text box and type in the new one, either as the control key character equivalent or the decimal value of the ASCII character.
Page 173: Tek 4014 Settings
Setup Menus Tek 4014 Settings This dialog box is only available if your version of TeemTalk supports graphics emulations. It is displayed when running the Tek 4014 emulation by selecting Tek Graphics in the Settings menu. Auto New Line Factory default: Unselected When selected, this will cause a carriage return command to be appended to every line feed command received.
Page 174 Setup Menus Screen Mapping Factory default: 1024 (x) by 768 (y) This option enables you to select the correct resolution for screen addressing when in Tek 4014 or Westward 2119 graphics modes. For Tek 4014 mode select 1024 (x) by 768 (y) resolution (default). For Westward 2119 mode select 1024 (x) by 784 (y) resolution.
Page 175: Gin Mouse Definitions
Setup Menus GIN Mouse Definitions This dialog box is only available if your version of TeemTalk supports graphics emulations. It is displayed by selecting GIN Mouse in the Settings menu. This enables you to specify the code which each mouse button sends when it is pressed and released.
Page 176: Attributes
Setup Menus Attributes This dialog box is displayed by selecting Attributes in the Settings menu. It enables you to specify the colours used in the emulation workspace and how text with attributes is displayed. To change the way a screen element is displayed, select the relevant item from the Screen Element list box, for example, Bold (BD) for characters with the bold attribute.
Page 177 Setup Menus Screen Element This list box enables you to select the screen element for definition. The Ansi Palette option allows you to specify which set of eight Foreground and Background colour indices are used when ANSI colour escape sequences are received.
Page 178 Setup Menus Swap Black/White Factory default: Unselected When selected, anything that has the white attribute will be displayed as black, and vice versa. AutoColour Factory default: Unselected This option is only applicable to the DEC VT terminal emulations. When selected, displayed characters are colour coded according to type.
Page 179: Customizing The Colour Selection
Setup Menus Customizing The Colour Selection You can change any of the 16 colours displayed in the Foreground and Background colour palettes. To do this, select the colour you wish to change in one of the palettes then click the Set Colour... button to display the Colour dialog box. This shows the basic and custom colours currently available for selection.
Page 180 Setup Menus the right. When you have the required colour, click the Add to Custom Colours button to apply the change to the set of custom colours. Numeric Value Method The numeric value of Hue, Lightness and Saturation, or the Red, Green and Blue percentage values can be entered directly in the text boxes.
Page 181: Define Keyboard Macros
Setup Menus Define Keyboard Macros This dialog box is displayed by selecting Keyboard Macros in the Settings menu. The Define Keyboard Macros dialog box enables you to redefine the function of most of the keys on your keyboard, including the key combinations listed below: Shift + Key Control + Key Control + Shift + Key...
Page 182: Defining A Key Or Key Combination
Setup Menus You can remove the selected definition or delete all the definitions by clicking the relevant Remove button. Defining A Key Or Key Combination 1. Click in the Program Key box then press the key or key combination to define. The current definition will be displayed.
Page 183: Specifying Characters
Setup Menus Specifying Characters There are various ways in which you can specify a particular character. For example, the ESC character can be specified using any one of the following five entries: _027 Decimal value (underscore character followed by a 3-digit number). \033 Octal value (backslash character followed by a 3-digit number).
Page 184: Soft Buttons
Setup Menus Soft Buttons This dialog box is displayed by selecting Soft Buttons in the Settings menu. TeemTalk for Windows CE A set of soft buttons can be displayed in the command bar either by clicking one of the two arrow buttons, or by pressing the keys Ctrl + Alt + Left Cursor or Ctrl + Alt + Right Cursor.
Page 185: Programming A Soft Button
Setup Menus button. Each level can be assigned a title which will be displayed under the Level button by entering up to eight characters in the Title box. The soft buttons can be removed from the display by setting the Visible Levels option to 0.
Page 186: Specifying Characters
Setup Menus For example, to program a button so that when it is pressed it performs the same function as pressing the keys Alt + F4 together, enter the following characters in the Command box: <ALT+F4> To program a button so that it performs the same function as pressing a sequence of keys one after the other, enter each virtual key name in the order required, enclosing each virtual key name with the <...
Page 187: Mouse Button Actions
Setup Menus Mouse Button Actions This dialog box is displayed by selecting Mouse Button Actions in the Settings menu. This enables you to specify the function of the left and right mouse buttons when they are clicked on their own or in conjunction with modifier keys. You can assign up to six functions to each button, either entering your own definition in the same format as described for keyboard macros and soft buttons, or selecting from a list of standard built-in functions.
Page 188 Setup Menus the hotspot feature. It enables you to send delimited text displayed on the screen to the host just by clicking on it. Delimiters are the same as for hotspots. The Move Cursor function can be used in any of the local block modes as a quick way of positioning the text cursor within a block of text.
Page 189: Button Tools
Setup Menus Button Tools (TeemTalk for Windows XPe only) This TeemTalk for Windows XPe dialog box is displayed by selecting Button Tools in the Settings menu. It enables you to redefine the button tools displayed in the toolbar. The Current Tool box displays the toolbar button and its function that is currently selected for editing, or located where a new button is to be inserted to its left in the toolbar.
Page 190: Adding A Space Between Buttons
Setup Menus 5. Specify the command to be performed when this button is clicked either by selecting from the Commands list or by typing your own definition in the Current Tool text box. 6. Click the Insert at Current button. 7.
Page 191: Specifying Key Functions
Setup Menus Specifying Key Functions You can cause a key function to be actioned by including the virtual key name of the key enclosed by the < and > characters. You may omit the VK_ and VT_ parts (etc.) of the virtual key name. For example, the Enter key would be specified as <ENTER>. To send the function of a key combination, type the <...
Page 192 Setup Menus Notes 6-108...
Page 193: Dec Vt Emulations
DEC VT Emulations DEC VT Emulations This chapter describes features of the DEC VT terminal emulations. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 194: Non-Wbt Mode
DEC VT Emulations additional Telnet options. Refer to the TCP/IP Connection Settings section in chapter 2 for details. For a modem connection, click the Modem button then click Advanced to display configuration options. Refer to the Modem Connection Settings section in chapter 2 for details.
Page 195 DEC VT Emulations For a modem connection, select Modem, specify the communications port in the Connect To box, then click Configure to display configuration options. Refer to the Modem Connection Settings section in chapter 2 for details. For a serial connection, select Serial, specify the communications port in the Connect To box, then click Configure for additional serial options.
Page 196: The Status Bar
DEC VT Emulations The Status Bar The status bar along the bottom of the display enables you to switch between modes and show the status of various operations. Item 1: This displays two LEDs. The first LED indicates whether or not you are connected to the host.
Page 197: Horizontal Scrolling
DEC VT Emulations Auto signifies that the emulation is in Auto Print mode in which the current cursor line is sent to the printer when a command for the cursor to move to the next line is issued. Controller signifies that the emulation is in Printer Controller mode in which the host has direct control over the printer.
Page 198 DEC VT Emulations Enhanced AT Keyboard Layout Normal Mode...
Page 199 DEC VT Emulations Enhanced AT Keyboard Layout DEC Mode...
Page 200: Typing Direction For Hebrew Language
DEC VT Emulations Typing Direction For Hebrew Language When ISO Hebrew or Ansi PC Hebrew 862 is selected as the Preferred Character Set in the Terminal Settings dialog box, the following key functions will be enabled: Ctrl + Alt + F1 Select Multinational 8-bit mode and left-to-right typing.
Page 201: Bq 3107 Emulation
BQ 3107 Emulation BQ 3107 Emulation This chapter describes the Bull BQ 3107 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 202: Non-Wbt Mode
BQ 3107 Emulation Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box. 6. Click Finish to return to the Terminal Connection Manager. 7. In the Terminal Connection Manager, display the Connections list, select the session name you specified earlier in step 3, then click the Connect button.
Page 203: The Status Bar
BQ 3107 Emulation The Status Bar The status bar displayed along the bottom of the window will show the status of various operations. F2 F3 F4 F5 F6 F13 F14 F15 Field 1: This will always display RUN, indiocating that the line shown corre- sponds to normal operation.
Page 204: Keyboard Mapping
BQ 3107 Emulation Keyboard Mapping The illustration on the following page shows where BQ 3107 keyboard functions are mapped to keys on the 101/102 key Enhanced AT keyboard layout. Special key functions that are provided on the BQ 3107 keyboard can be mapped to any key on your keyboard by using the BQ virtual key names listed in the Define Keyboard Macros dialog box.
Page 205 BQ 3107 Emulation Enhanced AT Keyboard Layout...
Page 206 BQ 3107 Emulation Notes...
Page 207: Dg 410/412 Emulation
DG 410/412 Emulation DG 410/412 Emulation This chapter describes the Data General D410/412 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 208: Non-Wbt Mode
DG 410/412 Emulation For a serial connection, click the Serial button, specify the communications port in the Connect To box, then click Advanced for additional serial options. Refer to the Serial Connection Settings section in chapter 2 for details. Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box.
Page 209: Keyboard Mapping
DG 410/412 Emulation Keyboard Mapping The illustration on the following page shows where DG 410/412 keyboard functions are mapped to keys on the 101/102 key Enhanced AT keyboard layout. Special key functions that are provided on the DG 410/412 keyboard can be mapped to any key on your keyboard by using the DG virtual key names listed in the Define Keyboard Macros dialog box.
Page 210 DG 410/412 Emulation Enhanced AT Keyboard Layout...
Page 211: Key Codes
DG 410/412 Emulation Composing Characters The Data General D410 keyboard has a SPCL key which enables you to generate characters from the DG International character set. You can generate the same characters by using the method described for the DEC emulation. Refer to the Compose Character Sequences section in the Keyboard Configuration chapter for details.
Page 212 DG 410/412 Emulation Notes...
Page 213: Hp 700-92/96 Emulation
HP 700-92/96 Emulation HP 700-92/96 Emulation This chapter describes features of the Hewlett Packard 700-92/96 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 214: Non-Wbt Mode
HP 700-92/96 Emulation For a modem connection, click the Modem button then click Advanced to display configuration options. Refer to the Modem Connection Settings section in chapter 2 for details. For a serial connection, click the Serial button, specify the communications port in the Connect To box, then click Advanced for additional serial options.
Page 215: Display Configuration
HP 700-92/96 Emulation 6. When you have specified the required settings in the New Connection dialog box, click the Connect button to make the connection. Note: You can save these settings as a connection template using the Save Session As dialog box. Refer to the Setup Menus chapter for details.
Page 216 HP 700-92/96 Emulation Enhanced AT Keyboard Layout 10-4...
Page 217: Buttons & Function Keys
HP 700-92/96 Emulation Buttons & Function Keys The buttons along the bottom of the HP 700-92/96 window indicate the current function of keys F1 through F8 on the keyboard, each key and equivalent button having several functions within the emulation. The buttons and equivalent function keys enable selection of various operating modes and display configurations.
Page 218 HP 700-92/96 Emulation Modify All - F2 This is similar to the Line Modify F1 function described previously, the only difference being that the editing mode is not exited when Return or Enter is pressed. F2 and its equivalent button acts as a toggle key, switching the mode on or off. The setting may be saved by selecting Save Session in the File menu.
Page 219 HP 700-92/96 Emulation Terminal Test - F5 When this button or F5 key is pressed, the HP 700-92/96 emulation will perform a self-test and display a test screen showing all the displayable characters. Memory Lock - F6 This enables data to be locked on the display so that it is not scrolled off the top of the window when display memory is full.
Page 220: Configuration Selection
HP 700-92/96 Emulation Auto LF - F8 This button and the F8 key enables or disables Auto Line Feed mode. When enabled, a line feed command is automatically appended to every carriage return command generated from the keyboard. The setting may be saved by selecting Save Session in the File menu.
Page 221 HP 700-92/96 Emulation Device Modes - F1 Clicking this button or pressing F1 will cause the Device Modes function labels to be displayed. The keys F1 through F8 will function as described in the following section entitled Device Modes. To Ext Dev - F2 This toggle function determines whether data is sent to the printer or not.
Page 222: Device Modes
HP 700-92/96 Emulation Copy Line - F8 When a printer is connected and enabled by the To Ext Dev function, clicking this button or pressing F8 will cause a copy of the line containing the cursor to be sent to the printer.
Page 223: Margins, Tabs & Start Column
HP 700-92/96 Emulation Log Bottom remains activated until either this button or F3 is pressed again, Log Top is activated, a reset is performed, or the emulation is exited. Log Top - F4 When the display memory becomes full and more data is received from the host or keyboard, lines of data from the top of the display are deleted to make way for the new data.
Page 224 HP 700-92/96 Emulation To change the current start column, move the cursor to the new starting point and click this button or press the F1 key. The start column will revert to that specified within setup when the emulation is reset or re-entered. Set Tab - F2 This function enables tab stops to be defined.
Page 225: Key Programming
HP 700-92/96 Emulation When data received from the host or entered through the keyboard reaches the specified right margin, the cursor will move to the left margin on the next line down (as long as InhEolWrp is not selected in the HP Settings dialog box and, in the case of keyboard-entered data, auto line feed mode is enabled).
Page 226: Key String Treatment
HP 700-92/96 Emulation Key String Treatment Each f-key and button definition displayed in the menu consists of two lines. The first line begins with the f-key number followed by space then a one-character attribute field. This field will contain either an uppercase L, T or N. These characters indicate the following: The key string is executed locally.
Page 227: Key String Definition
HP 700-92/96 Emulation Key String Definition The second line of each f-key definition contains the character string that is to be displayed, executed, and/or transmitted to the host when the key or button is pressed. The string may contain alphanumeric characters, control characters, and explicit escape sequence characters entered when Display Functions mode is enabled by pressing F7 or the Display Functns button.
Page 228: Character Display Attributes
HP 700-92/96 Emulation Character Display Attributes The HP 700-92/96 emulation incorporates various display attributes which can be enabled by host commands or from the keyboard by the user. These attributes are listed in the table below. When an attribute or set of attributes are enabled, they affect all subsequently displayed characters until an end attribute command or another attribute command is received, or the end of the line is reached.
Page 229: Ibm 3270 Emulation
IBM 3270 Emulation IBM 3270 Emulation This chapter describes features of the IBM 3270 terminal emulation. Introduction The IBM 3270 emulator provides emulation of all four models of the IBM 3278 alphanumeric terminal and also supports the IBM 3287-1 printer. The terminal emulation supports Extended Attribute mode which allows different representation of highlighted fields and permits host definition of text colours.
Page 230: Non-Wbt Mode
IBM 3270 Emulation 5. Select the IBM 3270 Model which determines the size of the display and whether or not extended attributes are supported. One of four display sizes can be selected: 3278/9-2 24 rows by 80 columns 3278/9-3 32 rows by 80 columns 3278/9-4 43 rows by 80 columns 3278/9-5...
Page 231 IBM 3270 Emulation 3. Display the IBM 3270 Settings dialog box if you wish to change the setting of the IBM 3270 Model option which determines the size of the display and whether or not extended attributes are supported. One of four display sizes can be selected: 3278/9-2 24 rows by 80 columns 3278/9-3...
Page 232: Network Virtual Terminal Mode
IBM 3270 Emulation Network Virtual Terminal Mode Network Virtual Terminal (NVT) mode allows the operator to communicate with a network gateway (in ASCII) for routing, logon etc, before the full IBM terminal emulation protocol is established. NVT mode is indicated by the symbol in the status line along the bottom of the display.
Page 233: The Status Line
IBM 3270 Emulation The Status Line The last line in the window is used to display status information in the form of symbols and alphanumeric characters. A coloured line separates status information from the rest of the display. Information is displayed in any of nine regions within the status line as listed below.
Page 234 IBM 3270 Emulation 6: Shift Symbol Colour Column Meaning Blue 43-45 Numeric lock on 7: Mode Symbol Symbol Colour Column Meaning Blue Insert mode on 8: Display Direction Symbol Colour Column Meaning Blue Normal display Blue Right-to-left mirror display 9: Cursor Position Symbol Colour Column...
Page 235: Do Not Enter
IBM 3270 Emulation Do Not Enter The Do Not Enter ( ) symbol will appear when input from the keyboard or mouse will not be accepted by the host (except Reset and SysReq). Symbols to the right of this will indicate the reason. Pressing the Reset key will remove some of these symbols from the status line.
Page 236: Typing Direction
IBM 3270 Emulation Typing Direction => or <= This indicates the direction in which characters are displayed on the screen when typed. The direction is toggled between left-to- right (normal) and right-to-left by pressing the keys Shift + / on the keypad.
Page 237: Text Display Options
IBM 3270 Emulation Text Display Options Display Right-to-Left The contents of the screen can be displayed in reverse, i.e. as a right-to-left mirror image, by pressing the keys Shift + Backspace. This is a toggle function, so pressing the keys again will revert to normal left-to-right display. An arrow will be displayed on the status line to indicate normal (right arrow) or mirror (left arrow) display.
Page 238: Keyboard Mapping
IBM 3270 Emulation keypad. The character N or L will be displayed on the status line to indicate which character set is currently active. Selecting the Numeral Swap option in the IBM 3270 Settings dialog box will cause all numbers to be displayed using the National character set when in Latin character set mode.
Page 239 IBM 3270 Emulation Enhanced AT Keyboard Layout 11-11...
Page 240: Record & Playback Keystrokes Facility
IBM 3270 Emulation Record & Playback Keystrokes Facility The record/playback keystrokes facility enables you to eliminate repetitive operations by using the Fn keys to store, retrieve and display data. The Fn keys can store a total of 1500 keystrokes. A sequence of recorded keystrokes may be interrupted so that keystrokes can be entered manually before continuing with the recording or playback.
Page 241: Playback Keystrokes
IBM 3270 Emulation 4. To finish and save the recording, press the Record key. Playback Keystrokes You can play back the contents of an Fn key as normal or one keystroke at a time. The following procedure describes normal play back. For one keystroke play back, select Single Step Macros in the Notice Board Setup dialog box.
Page 242: Error Codes
IBM 3270 Emulation 3. Use the Left or Right cursor keys to move the cursor one character position at a time through the macro, or the Up or Down cursor keys to move 20 character positions at a time. 4. If required, press the Insert key to toggle between Insert and Edit mode, as indicated in the status line.
Page 243: Notice Board Facility
IBM 3270 Emulation 9019 In Record or Play mode. While the Record/play pause indicator was displayed on the status line you pressed an invalid key (e.g. Play key in Record mode, or Record key in Play mode). Remedy: Press the Reset key. Notice Board Facility Introduction The Notice Board is an area of the display in which copied data can be stored and...
Page 244: Copying Screen Data To A Function Key
IBM 3270 Emulation 4. Press F13 to copy the selected area. The copied area (i.e. the target) will be highlighted in red. 5. Use the cursor keys to move the red target area to the required position on the display. You can also use the Jump key to move the target area to the host screen or Notice Board.
Page 245: Ibm 5250 Emulation
IBM 5250 Emulation IBM 5250 Emulation This chapter describes features of the IBM 5250 terminal emulation. Introduction The IBM 5250 emulator provides emulation of 5250 type alphanumeric terminals, both monochrome (green/white plus attributes) and colour. Colours may be modified using the Attribute Settings dialog box. This emulation can be used for connection to an IBM AS/400, System/36 or System/38.
Page 246 IBM 5250 Emulation as monochrome (green for normal characters, white for intense attribute) or colour for attributes. The terminal models currently supported and their display character- istics are listed below. Type Display Rows x Columns 5291_1 Monochrome 24 x 80 5292_2 Colour 24 x 80...
Page 247: Non-Wbt Mode
IBM 5250 Emulation Make the relevant selections then click OK to return to the Host Information dialog box, then click Next. 9. The following four dialog boxes provide further configuration options which are described in chapter 2. Click Next to advance through the dialog boxes. Automate Login Process Printer Port Settings GUI Overrides...
Page 248 IBM 5250 Emulation 3487_HC Colour 24 x 80 5555_B01 Monochrome 24 x 80 5555_C01 Colour 24 x 80 The printer models supported are listed below: 3812-1 Single byte printer 5553-B01 Double byte printer If double byte character sets (e.g. Japanese) are supported and you wish to use them, then select either 5555_B01 (monochrome) or 5555_C01 (colour) for display, or 5553-B01 for printing.
Page 249: Network Virtual Terminal Mode
IBM 5250 Emulation Network Virtual Terminal Mode Network Virtual Terminal (NVT) mode allows the operator to communicate with a network gateway (in ASCII) for routing, logon etc, before the full IBM terminal emulation protocol is established. NVT mode is indicated by the absence of the symbol in the status line along the bottom of the window.
Page 250: Keyboard Mapping
IBM 5250 Emulation Insert mode can be disabled by pressing the Insert key again, pressing the Reset key, or by performing any action that sends data to the host, such as pressing the Enter, Clear, or PF keys. Indicates when input from the keyboard or mouse will not be accepted by the host. When this is because an error has occured, as shown in the error line, pressing the Reset key will remove the error.
Page 251 IBM 5250 Emulation Enhanced AT Keyboard Layout 12-7...
Page 252: Text Display Options
IBM 5250 Emulation Text Display Options Display Right-to-Left The contents of the screen can be displayed in reverse, i.e. as a right-to-left mirror image, by pressing the keys Shift + Backspace. This is a toggle function, so pressing the keys again will revert to normal left-to-right display. An arrow will be displayed on the status line to indicate normal (right arrow) or mirror (left arrow) display.
Page 253: Record & Playback Keystrokes Facility
IBM 5250 Emulation keypad. The character N or L will be displayed on the status line to indicate which character set is currently active. Selecting the Numeral Swap option in the IBM 5250 Settings dialog box will cause all numbers to be displayed using the National character set when in Latin character set mode.
Page 254: Playback Keystrokes
IBM 5250 Emulation 2. Press the Fn key which will store the keystrokes. (On 101/102 keyboards you can also use Shift + Fn.) The status line will display R**** F* where R indicates you are in Record mode, **** is the number of keystrokes that may be stored, and F* is the number of the Fn key pressed.
Page 255: Fax Image Support
IBM 5250 Emulation 9001 Exceeded the maximum number of allowed keystrokes. Remedy: Press the Record key to exit Record mode. To record a new keystroke sequence, either: a) Press the Record key and the target Fn key that has erasable data, then enter the new data.
Page 256 IBM 5250 Emulation Notes 12-12...
Page 257: Ibm 3151 Emulation
IBM 3151 Emulation IBM 3151 Emulation This chapter describes features of the IBM 3151 terminal emulation. Introduction The IBM 3151 emulation is based on the native mode of the IBM 3151 Model 11 terminal. The emulation is configured using the IBM 3151 Settings dialog box which is described in the Setup Menus chapter.
Page 258: Non-Wbt Mode
IBM 3151 Emulation 4. Select the IBM 3151 terminal emulation in the Emulation list box. 5. Click Next to display the Host Information dialog box. For a TCP/IP connection, click the TCP/IP button, enter the name or internet address of the host computer in the Host Name box, then click Advanced for additional Telnet options.
Page 259: The Status Bar
IBM 3151 Emulation 5. When you have specified the required settings in the New Connection dialog box, click the Connect button to make the connection. Note: You can save these settings as a connection template using the Save Session As dialog box. Refer to the Setup Menus chapter for details.
Page 260: Keyboard Mapping
IBM 3151 Emulation try to insert a character or line in a screen already full when the Forcing Insert option is set to Off. If two or more messages are sent to a particular field, then the message with the highest priority will be displayed.
Page 261 IBM 3151 Emulation Enhanced AT Keyboard Layout 13-5...
Page 262: Defining Function Keys
IBM 3151 Emulation Defining Function Keys The keys mapped as F1 through F12 can be redefined from the keyboard or by the host. The function keys can store up to 128 characters between them and can include escape sequences and ASCII control characters in addition to character strings. Here we describe how to define a function key from the keyboard.
Page 263: Mdis Prism Emulations
MDIS Prism Emulations MDIS Prism Emulations This chapter describes the MDIS Prism terminal emulations. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 264: Non-Wbt Mode
MDIS Prism Emulations For a serial connection, click the Serial button, specify the communications port in the Connect To box, then click Advanced for additional serial options. Refer to the Serial Connection Settings section in chapter 2 for details. Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box.
Page 265: Keyboard Mapping
MDIS Prism Emulations Keyboard Mapping The following illustration shows where MDIS Prism keyboard functions are mapped to keys on the 101/102 key Enhanced AT keyboard layout. Special key functions that are provided on the MDIS Prism keyboard can be mapped to any key on your keyboard by using the MD virtual key names listed in the Define Keyboard Macros dialog box.
Page 266 MDIS Prism Emulations Enhanced AT Keyboard Layout 14-4...
Page 267: Pt250 Emulation
PT250 Emulation PT250 Emulation This chapter describes the Prime PT250 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 268: Non-Wbt Mode
PT250 Emulation Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box. 6. Click Finish to return to the Terminal Connection Manager. 7. In the Terminal Connection Manager, display the Connections list, select the session name you specified earlier in step 3, then click the Connect button.
Page 269: The Status Line
PT250 Emulation The Status Line The last line in the window is used to display a status line consisting of eleven fields which show the status of various operations. The following illustration shows the information that is displayed by default. 10 11 Field 1: Will display either ONLINE or LOCAL, depending on whether the...
Page 270 PT250 Emulation GR indicates the Block Graphics character set. LD indicates the Line Drawing character set. Field 7: Indicates the current transmission status as follows: AUX SEND is displayed when data is being sent to an auxiliary device. KEYBD LOCK is displayed when the keyboard is locked to prevent data entry, usually set by the application.
Page 271: Keyboard Mapping
PT250 Emulation Field 9: Displays messages defined by the program or user. Field 10: Displays NUM when Num Lock is activated, otherwise this field is blank. Field 11: Displays INS when Insert mode is activated. In Replace mode (default), this field is blank. Keyboard Mapping The following illustration shows where PT250 keyboard functions are mapped to keys on the 101/102 key Enhanced AT keyboard layout.
Page 272 PT250 Emulation Enhanced AT Keyboard Layout 15-6...
Page 273: Displaying Alternate Characters
PT250 Emulation Displaying Alternate Characters PT250 mode uses two character sets called Standard and Alternate to display characters. Both sets incorporate all the characters contained in the ASCII (7-bit or lower half) and PT250 Additional (8-bit or upper half) character set tables shown in the Character Sets appendix.
Page 274 PT250 Emulation Notes 15-8...
Page 275: Siemens 97801 Emulation
Siemens 97801 Emulation Siemens 97801 Emulation This chapter describes the Siemens 97801 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 276: Non-Wbt Mode
Siemens 97801 Emulation Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box. 6. Click Finish to return to the Terminal Connection Manager. 7. In the Terminal Connection Manager, display the Connections list, select the session name you specified earlier in step 3, then click the Connect button.
Page 277: Keyboard Mapping
Siemens 97801 Emulation Keyboard Mapping The following illustration shows where Siemens 97801 keyboard functions are mapped to keys on the 101/102 key Enhanced AT keyboard layout. Special key functions that are provided on the Siemens 97801 keyboard can be mapped to any key on your keyboard by using the SI virtual key names listed in the Define Key- board Macros dialog box.
Page 278 Siemens 97801 Emulation Enhanced AT Keyboard Layout 16-4...
Page 279: Ta6530 Emulation
TA6530 Emulation TA6530 Emulation This chapter describes features of the Tandem 6530 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 280: Non-Wbt Mode
TA6530 Emulation Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box. 6. Click Finish to return to the Terminal Connection Manager. 7. In the Terminal Connection Manager, display the Connections list, select the session name you specified earlier in step 3, then click the Connect button.
Page 281: The Status Line
TA6530 Emulation The Status Line The last (25th) line in the window is used to display messages and status information. You can enable or disable display of a border which separates this line from the rest of the lines above it by setting the Status Border option in the TA6530 Settings dialog box accordingly.
Page 282: Operating Modes
TA6530 Emulation Operating Modes The Tandem 6530 emulation operates in one of three main modes, Conversational, Block, or ANSI. Conversational and Block modes are normally used for applications running on a NonStop host system, and ANSI mode for applications running on the LXN host system.
Page 283: The Rule Cursor
TA6530 Emulation ANSI Mode In ANSI mode, characters are sent to the host as you type them, and standard ANSI (American National Standard Institute) functions are executed. Applications that run on the LXN host system generally recognize and use these functions. The status line will display ANSI when you are in ANSI mode.
Page 284 TA6530 Emulation Enhanced AT Keyboard Layout 17-6...
Page 285: Unisys T27 Emulation
Unisys T27 Emulation Unisys T27 Emulation This chapter describes features of the Unisys T27 terminal emulation. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 286: Non-Wbt Mode
Unisys T27 Emulation Make the relevant selections then click OK to return to the Host Information dialog box, then click Next to display the Advanced Options dialog box. 6. Click Finish to return to the Terminal Connection Manager. 7. In the Terminal Connection Manager, display the Connections list, select the session name you specified earlier in step 3, then click the Connect button.
Page 287: The Status Bar
Unisys T27 Emulation The Status Bar LTIA On: The host connection is active, but the Unisys T27 emulation does not have an active address. Off: No line activity; or the Unisys T27 emulation transmitted a character to the host, or the user pressed LOCAL.
Page 288: Keyboard Mapping
Unisys T27 Emulation Off: Transmission has been successfully completed or the T27 is switched to local mode. Keyboard Mapping The following illustration shows where Unisys T27 keyboard functions are mapped to keys on the 101/102 key Enhanced AT keyboard layout. Special key functions that are provided on the Unisys T27 keyboard can be mapped to any key on your keyboard by using the UT virtual key names listed in the Define Keyboard Macros dialog box.
Page 289 Unisys T27 Emulation Enhanced AT Keyboard Layout 18-5...
Page 290 Unisys T27 Emulation Notes 18-6...
Page 291: Wyse Emulations
Wyse Emulations Wyse Emulations This chapter describes features of the Wyse WY-50, WY-50+ and WY-60 terminal emulations. Session Configuration WBT Mode This section describes the basic procedure for creating a session configuration when the terminal is in WBT mode. The options available are described in detail in chapter 1.
Page 292: Non-Wbt Mode
Wyse Emulations 5. Click Next to display the Host Information dialog box. For a TCP/IP connection, click the TCP/IP button, enter the name or internet address of the host computer in the Host Name box, then click Advanced for additional Telnet options. Refer to the TCP/IP Connection Settings section in chapter 2 for details.
Page 293 Wyse Emulations The TVI 910+, TVI 920 and TVI 925 emulations provide compatibility with software designed to drive the TeleVideo 910+, 920 and 925 terminals, respec- tively, as emulated by the Wyse WY-50/50+/60 terminals. 3. Display the File menu from the command bar and select New Connection to display the New Connection dialog box.
Page 294: Display Format
Wyse Emulations Display Format Below the command bar (described in chapter 2) the display is divided into three areas by default: the status line, the data area, and the label line. The status line which is used to display information relating to the emulation and messages from the application.
Page 295: Keyboard Mapping
Wyse Emulations Field 2: Indicates the number of the page that is currently displayed. No message is displayed when the current page is 0. Field 3: * indicates that Monitor mode is on. In this mode, received codes are not actioned but displayed as symbolic representations.
Page 296 Wyse Emulations Enhanced AT Keyboard Layout 19-6...
Page 297 Initialization Commands Initialization Commands This chapter describes all the initialization commands that can be included in the registry or on the command line to run the emulator. Introduction This chapter describes the registry entries and command line options that can be used to specify how the emulator is initially run.
Page 298: Command Summary
Initialization Commands Command Summary Note that ◆ indicates the command is only available for NT or XP embedded versions of the emulator. ■ indicates the command is only available if your version of TeemTalk supports graphics emulations. Host Connection Command Function Registry Entry Command Line Load Winsock on start-up...
Page 299 Initialization Commands Disable toolbar none Disable menu bar/pop-ups, toolbar none -CB1 ◆ Disable menu bar none ◆ Disable menu bar & pop-ups none -MB1 Disable File menu FileMenu = "off" Disable Factory item Factory = "off" none Disable Reset item Reset = "off"...
Page 300: Keyboard & Mouse
Initialization Commands Disable Unisys T27 item UnisysT27 = "off" none Disable Wyse item Wyse = "off" none ◆ Disable Tools menu ToolsMenu = "off" Disable scroll bar ScrollBar = "off" ◆ Soft button levels displayed ButtonLevels = 0-4 -BL0-4 Disable status bar & DEC status StatusLine = "off"...
Page 301: Action On Host Connection Close
Initialization Commands Host Connection Load Winsock On Start-up Registry Entry: None Command Line: -LW Default Setting: Off This will initialize the Winsock stack immediately when the emulator is started, enabling dialup over PPP or SLIP to gain a connection to a service provider. Action On Host Connection Close Registry Entry: ExitOnClose = "on"...
Page 302 Initialization Commands Disable 'Exit' Message Box Registry Entry: WarnExit = "off" Command Line: -J Default Setting: Enabled A message box will be displayed if you attempt to exit the emulator while a network session is still active. These commands will disable the message box so that the emulator automatically closes the network connection when it is exited.
Page 303: Disable Bell
Initialization Commands Session Configuration Start-up Command Group To Action Registry Entry: None Command Line: -Nname Default Setting: Default You can specify more than one set of start-up commands in the registry. This enables you to configure each instance of the emulator differently. Each set of commands other than the default set must have the following heading in the registry under HKLM\Software\Pericom\<product name>: Startup,name...
Page 304 Initialization Commands Enable Debug (File Capture/Replay) Registry Entry: None Command Line: -Debug Default Setting: Disabled This command is only available for NT or XP embedded versions of the emulator. It enables the File Capture and File Replay options in the File menu which allow received host data to be logged in a file then replayed.
Page 305: Disable Window Frame Resize
Initialization Commands Display Window Minimized On Start-Up Registry Entry: WindowSize = "minimized" Command Line: -MI Default Setting: Not applicable These commands are only available for NT or XP embedded versions of the emulator. They will cause the window to be displayed as an icon when the emulator is loaded. Window Maximized On Start-Up Registry Entry: WindowSize = "maximized"...
Page 306: Window Title
Initialization Commands Window Title Registry Entry: None Command Line: -T"title" Default Setting: Emulator name This enables you to specify the title that is to be displayed in the title bar. This is useful when you are running more than one instance of the emulator. If no title is specified then the name of your version of the emulator will be displayed.
Page 307: Disable Minimize Button
Initialization Commands Disable Minimize Button Registry Entry: MinimizeBox = "off" Command Line: -MN Default Setting: on These commands will remove the minimize button from the emulator window. Disable Maximize Button Registry Entry: MaximizeBox = "off" Command Line: -MX Default Setting: on These commands will remove the maximize button from the emulator window.
Page 308: Disable Command Bar
Initialization Commands Disable System Menu & Min/Maximize Buttons Registry Entry: SystemMenu = "none" Command Line: None Default Setting: on This command is only available for NT or XP embedded versions of the emulator. It will remove the System (Control) menu icon and the Minimize and Maximize buttons from the emulator window.
Page 309: Disable Toolbar
Initialization Commands Disable Toolbar Registry Entry: None Command Line: -L Default Setting: on This command will remove the toolbar from the window. Disable Menu Bar, Pop-Up Menus & Toolbar Registry Entry: None Command Line: -CB1 Default Setting: on This will remove the menu bar and toolbar from the emulator window and prevent access to pop-up menus using keyboard commands.
Page 310: Disable File Menu
Initialization Commands Disable File Menu Registry Entry: FileMenu = "off" Command Line: -MF Default Setting: on These commands will disable the File menu. Individual items in the File menu can be disabled by using the following registry entries: Disable Factory item Factory = "off"...
Page 311: Disable Settings Menu
Initialization Commands Disable Settings Menu Registry Entry: SettingsMenu = "off" Command Line: -MS Default Setting: on These commands will disable the Settings menu. Individual items in the Settings menu can be disabled by using the following registry entries: Disable Attributes item Attributes = "off"...
Page 312: Soft Buttons Displayed
Initialization Commands Soft Buttons Displayed Registry Entry: ButtonLevels = 0-4 Command Line: -BL0-4 Default Setting: 1 These commands are only available for NT or XP embedded versions of the emulator. A set of soft buttons is displayed at the bottom of the emulatoor window by default. There are four soft button levels.
Page 313: Flashing Characters Enabled In All Sessions
Initialization Commands Flashing Characters Enabled In All Sessions Registry Entry: None Command Line: -FB Default Setting: off This enables characters with the flashing attribute to be displayed as such in all session windows in addition to the currently focused window. Reflection 4 Colour Support Registry Entry: iR4colours = "on"...
Page 314: Crosshair Cursor Size
Initialization Commands Crosshair Cursor Size Registry Entry: CrosshairSize = 1-1024 Command Line: -X1-1024 Default Setting: 1024 Only applicable to versions of TeemTalk that support graphics emulations. This command specifies the size of the graphics cursor, where size is a numeric value in the range 1 to 1024, i.e.
Page 315: Disable Backing Store
Initialization Commands Disable Backing Store Registry Entry: BackingStore = “off” Command Line: -B Default Setting: on Only applicable to versions of TeemTalk that support graphics emulations.When TeemTalk is in ReGIS mode it automatically stores a copy of graphics data in memory when graphics are initially drawn by the host in the window, a feature known as ‘backing store’.
Page 316: Disable Editing Functions
Initialization Commands Keyboard & Mouse Convert £ To $ (MDIS P9) Registry Entry: MDCUK = "Yes" Command Line: None Default Setting: no This command is only applicable to the MDIS P9 emulation. It will convert the £ character to $ and vice versa on the UK keyboard. Disable Editing Functions Registry Entry: MouseEdit = "disabled"...
Page 317: Aux Port Opened At Start-Up
Initialization Commands Auxiliary Port Set Aux Port As Bidirectional Registry Entry: None Command Line: -BA1 Default Setting: Disabled This causes the auxiliary port to be set as bidirectional. Aux Port Opened At Start-Up Registry Entry: None Command Line: -BA2 Default Setting: Disabled This causes the auxiliary port to be opened on start-up.
Page 318 Initialization Commands Notes 20-22...
Page 319: Virtual Key Names
Virtual Key Names Virtual Key Names This appendix lists all the supported virtual key names which enable you to include a specific key function in a user definition. Standard Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name 0 - 9 VK_0 - VK_9 Keypad 0 - 9...
Page 320: Bq 3107 Virtual Key Names
Virtual Key Names AT&T 4410 Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name Backspace AT_BACKSPACE F1 - F8 AT_F1 - AT_F8 Break AT_BREAK Home Down AT_HOMEDOWN Clear AT_CLEAR Home Up AT_HOMEUP Cursor Down AT_DOWN Line Feed AT_LINEFEED Cursor Left AT_LEFT...
Page 321: Dec Vt500 Virtual Key Names
Virtual Key Names DEC VT500 Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name Back Tab VT_CSIZ Insert VT_INSERT Break VT_BREAK Keypad 0 - 9 VT_PAD0 - 9 Backspace VT_BACKSPACE Keypad Comma VT_COMMA Compose Character VT_COMPOSE Keypad Decimal VT_PADDECIMAL Cursor Down...
Page 322: Ibm 3270 Virtual Key Names
Virtual Key Names HP 700-92/96 Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name Backspace HP_BACKSPACE Insert Wrap HP_INSERTWRAP Clear Display HP_CLEARMEM Menu HP_MENU Clear Line HP_CLEARLINE Next Page HP_NEXTPAGE Cursor Down HP_DOWN Previous Page HP_PREVPAGE Cursor Left HP_LEFT Print...
Page 323: Ibm 5250 Virtual Key Names
Virtual Key Names Field Mark IB_FIELDMARK Reverse Screen IB_REV_SC Fn Edit IB_FEDIT Rule Display IB_RULE Go To End Of Line IB_GO_EOL Selectable Field Tab IB_FIELDTAB Home IB_HOME System Request IB_SYSREQ Insert Mode IB_INSERT IB_TAB IBM 5250 Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name...
Page 324: Mdis Prism Virtual Key Names
Virtual Key Names MDIS Prism Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name Back Tab MD_BACKTAB Keypad Comma MD_PADCOMMA Backspace MD_BACKSPACE Keypad Decimal MD_PADDECIMAL Break MD_BREAK Keypad Minus MD_PADMINUS Clear MD_CLEAR Line Feed MD_LINEFEED Cursor Down MD_DOWN Print Screen MD_PRINT...
Page 325: Sco Console Virtual Key Names
Virtual Key Names SCO Console Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name Backspace SC_BACKSPACE F1 - F12 SC_F1 - SC_F21 Cursor Down SC_DOWN F1 - F12 + Shift SC_S_F1 - SC_S_F12 Cursor Left SC_LEFT F1 - F12 + Ctrl SC_C_F1 - SC_C_F12 Cursor Right...
Page 326: Tvi 955 Virtual Key Names
Virtual Key Names TVI 955 Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name Back Tab TV_BACKTAB F0 - F22 TV_F0 - TV_F22 Backspace TV_BACKSP Go To TV_GOTO Break TV_BREAK Keypad 00 TV_PAD00 Clear Entry TV_CLRENTRY Line Feed TV_LINEFEED Clear Space...
Page 327: Viewdata Virtual Key Names
Virtual Key Names Viewdata Virtual Key Names Key Function Virtual Key Name Key Function Virtual Key Name * (Star) PR_STAR Cursor Right PR_RIGHT # (Hash) PR_HASH Cursor Up PR_UP Cancel Print PR_CANCEL Exit to ANSI mode PR_EXIT Cursor Down PR_DOWN Reveal PR_REVEAL Cursor Left...
Page 328: Teemtalk Virtual Key Name Functions
Virtual Key Names TeemTalk Virtual Key Name Functions TeemTalk provides additional virtual key name functions for special tasks such as sending text to a file or the serial port, and reading text from a file to place in the keyboard buffer as if typed. Key Function Virtual Key Name Start Send Text sequence...
Page 329: Reading Text From A File
Virtual Key Names Reading Text From A File The following command format is used to read a string from a file and push it into the keyboard buffer as if typed: <VK_FILE_I><filename>max length,retries,termination char- acter <VK_FEND> The string is terminated when the maximum length is read, or the maximum number of retries is reached, or the termination character is read.
Page 330 Virtual Key Names Notes A-12...
Page 331 Character Sets Character Sets This appendix shows the supported character sets. Introduction Each character set consists of a series of control characters and displayable charac- ters. Displayable characters are alphanumeric, symbolic or graphic characters that can be displayed on the screen or printed by a hardcopy device. Control characters enable the terminal emulation or the printer to perform specific tasks, such as a line feed or carriage return.
Page 332 Character Sets ASCII CHARACTER SET (Multinational 7 Bit) COLUMN BITS 4 3 2 1 0000 0001 0010 " 0011 XOFF 0100 0101 0110 & ´ 0111 1000 1001 1010 1011 < 1100 1101 > 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL The ASCII (American Standard Code for Information Interchange) character set will be selected when the language is set to North American, or the Character Set Mode option in the Emulation Settings dialog box is set to Multinational.
Page 333 Character Sets NATIONAL REPLACEMENT CHARACTERS BINARY BIT OCTAL DECIMAL HEXADECIMAL ASCII £ British à â ç ê î ô é ù è û Canadian Danish Ä Æ Ø Å Ü ä æ ø å ü Norwegian £ ¨ ´ Dutch Ä...
Page 334 Character Sets DEC ADDITIONAL CHARACTER SET (Multinational 8 Bit) COLUMN BITS 4 3 2 1 ° à 0000 À ¡ ± á ñ 0001 Á Ñ ¢ â ò 0010 Â Ò £ ã ó 0011 Ã Ó ¨ ä ô...
Page 335 Character Sets DEC LINE DRAWING CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 " 0010 0011 XOFF 0100 0101 ° 0110 & ´ ± 0111 1000 ≤ 1001 ≥ 1010 π 1011 ≠ < 1100 £ 1101 1110 >...
Page 336 Character Sets ISO LATIN-1 ADDITIONAL CHARACTER SET (Multinational 8 Bit) COLUMN BITS 4 3 2 1 ° à 0000 À NBSP ¡ ± á ñ 0001 Á Ñ ¢ â ò 0010 Â Ò £ ã ó 0011 Ã Ó ¤...
Page 337 Character Sets ISO LATIN-2 ADDITIONAL CHARACTER SET (Multinational 8 Bit) COLUMN BITS 4 3 2 1 ° ´ ´ 0000 NBSP ´ á ´ 0001 Á â 0010 Â ó 0011 Ó ¤ ´ ä ô 0100 Ä Ô ´´ ´...
Page 338 Character Sets ANSI 437 CHARACTER SET COLUMN BITS 4 3 2 1 0000 Ç É á ß 0001 ü æ í 0010 é Æ ó 0011 â ô ú 0100 ä ö ñ 0101 à ò Ñ µ 0110 å û...
Page 339 Character Sets ANSI 850 CHARACTER SET COLUMN BITS 4 3 2 1 0000 Ç É á Ó 0001 ü æ í ß 0010 é Æ ó Ê Ô 0011 â ô ú Ë Ò 0100 ä ö ñ È õ ¶...
Page 340 Character Sets ANSI 858 CHARACTER SET This table forms the second half of the ANSI 858 character set, the first half being the ASCII character set. The ANSI 858 character set is used when the Preferred Char. Set option in the Terminal Settings dialog box is set to Ansi and the Ansi Code Page option is set to 858.
Page 341 Character Sets ANSI 1250 CHARACTER SET COLUMN BITS 4 3 2 1 ° ´ ´ 0000 NBSP ´ á ´ 0001 Á â 0010 Â ó 0011 Ó ¤ ´ ä ô 0100 Ä Ô ´´ ´´ ´ 0101 ’ ´...
Page 342 Character Sets DG 410/412 WORD PROCESSING, MATH & GREEK ALPHABET CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 ß 0011 XOFF 0100 0101 ƒ 0110 0111 1000 Ω 1001 1010 1011 ¶ 1100 1101 1110 1111 • OCTAL KEY: DECIMAL...
Page 343 Character Sets DG 410/412 LINE DRAWING CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 ¢ 1111 OCTAL KEY: DECIMAL HEXADECIMAL B-13...
Page 344 Character Sets WYSE NATIVE MODE CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 " 0010 0011 0100 0101 & 0110 0111 ´ 1000 1001 1010 1011 < 1100 1101 > 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This character set is used by all Wyse emulations and associated emulations. In WY-60 mode this is the default primary character set.
Page 345 Character Sets WY-60 MULTINATIONAL (CODE PAGE 437) CHARACTER SET COLUMN BITS 4 3 2 1 0000 Ç É á ß 0001 ü æ í 0010 é Æ ó 0011 â ô ú 0100 ä ö ñ 0101 à ò Ñ µ...
Page 346 Character Sets WY-60 MULTINATIONAL (CODE PAGE 850) CHARACTER SET COLUMN BITS 4 3 2 1 0000 Ç É á Ó 0001 ü æ í ß 0010 é Æ ó Ê Ô 0011 â ô ú Ë Ò 0100 ä ö ñ...
Page 347 Character Sets WY-60 PC EQUIVALENT CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 " 0010 0011 0100 ¶ 0101 § & 0110 0111 ´ 1000 1001 1010 1011 < 1100 1101 > 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This Wyse character set is only available in WY-60 mode.
Page 348 Character Sets WY-60 STANDARD ASCII CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 " 0011 0100 0101 & 0110 0111 ´ 1000 1001 1010 1011 < 1100 1101 > 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This Wyse character set is only available in WY-60 mode. B-18...
Page 349 Character Sets WY-60 STANDARD ANSI CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 " 0011 0100 0101 & 0110 ° 0111 ´ ± 1000 1001 ≤ 1010 ≥ 1011 π < 1100 ≠ 1101 £ > 1110 ·...
Page 350 Character Sets WY-60 GRAPHICS 1 CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This Wyse character set is only available in WY-60 mode. B-20...
Page 351 Character Sets WY-60 GRAPHICS 2 CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This Wyse character set is only available in WY-60 mode. B-21...
Page 352 Character Sets WY-60 GRAPHICS 3 CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This Wyse character set is only available in WY-60 mode. B-22...
Page 353 Character Sets PT250 ADDITIONAL CHARACTER SET COLUMN BITS 4 3 2 1 ° à 0000 À ¡ ± á ñ 0001 Á Ñ ¢ â ò 0010 Â Ò ã ó £ 0011 Ã Ó ¤ ä ô 0100 Ä Ô...
Page 354 Character Sets PT250 LINE DRAWING CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This is a special PT250 character set which is used by some applications. B-24...
Page 355 Character Sets PT250 BLOCK GRAPHICS CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL This is a special PT250 character set which is used by some applications. B-25...
Page 356 Character Sets SIEMENS 97801 INTERNATIONAL A CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 " 0011 XOFF 0100 0101 & 0110 0111 ´ 1000 1001 1010 1011 < 1100 1101 > 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL B-26...
Page 357 Character Sets SIEMENS 97801 INTERNATIONAL CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 " 0010 0011 XOFF ¤ 0100 0101 & 0110 0111 ´ 1000 1001 1010 1011 < 1100 1101 > ¯ 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL B-27...
Page 358 Character Sets SIEMENS 97801 GERMAN CHARACTER SET COLUMN BITS 4 3 2 1 § 0000 0001 0010 " 0011 XOFF 0100 0101 & 0110 0111 ´ 1000 1001 1010 Ä ä 1011 < Ö ö 1100 1101 Ü ü > ß...
Page 359 Character Sets SIEMENS 97801 EURO CHARACTER SET COLUMN BITS 4 3 2 1 è © 0000 Å Ω à é ´ ß Æ 0001 µ 0010 á ê ñ Ð · ° â ë ò 0011 XOFF 0100 ä ó ù...
Page 360 Character Sets SIEMENS 97801 BRACKETS CHARACTER SET COLUMN BITS 4 3 2 1 0000 0001 0010 0011 XOFF 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 OCTAL KEY: DECIMAL HEXADECIMAL B-30...
Page 361 Character Sets IBM 3270 & IBM 5250 ENGLISH (U.S.), CANADIAN BILINGUAL & NETHERLANDS CHARACTER SET ° & ø Ø µ é É £ ÷ â ê Â Ê ¥ ä ë Ä Ë · © à è À È á í...
Page 362 Character Sets IBM 3270 & IBM 5250 ENGLISH (U.K.) CHARACTER SET ° & ø Ø µ ¢ é É ÷ â ê Â Ê ¥ ä ë Ä Ë · © à è À È á í Á Í § ã...
Page 363 Character Sets IBM 3270 & IBM 5250 DANISH & NORWEGIAN CHARACTER SET ° & µ ¢ æ å é É ü £ ÷ â ê Â Ê ¥ ä ë Ä Ë · © à è À È á í Á...
Page 364 Character Sets IBM 3270 & IBM 5250 FRENCH CHARACTER SET & ø Ø ¢ é è ç É ¨ ÷ â ê Â Ê ¥ ä ë Ä Ë · © À È á í Á Í ã î Ã Î...
Page 365 Character Sets IBM 3270 & IBM 5250 GERMAN & AUSTRIAN CHARACTER SET ° & ø Ø µ ¢ ä ü Ö é É ß £ ÷ â ê Â Ê ¥ ë Ë · © à è À È á í...
Page 366 Character Sets IBM 3270 & IBM 5250 ITALIAN CHARACTER SET & ø Ø µ ¢ à è ç É ì ÷ â ê Â Ê ¥ ä ë Ä Ë · © À È á í Á Í ã î Ã...
Page 367 Character Sets IBM 3270 & IBM 5250 SPANISH CHARACTER SET ° & ø Ø µ ¢ é É ¨ £ ÷ â ê Â Ê ¥ ä ë Ä Ë · © à è À È á í Á Í §...
Page 368 Character Sets IBM 3270 & IBM 5250 SWEDISH & FINNISH CHARACTER SET ° & ø Ø µ ¢ ä å É ü £ ÷ â ê Â Ê ¥ ë Ë · © à è À È á í Á Í...
Page 369 Character Sets IBM 3270 & IBM 5250 BELGIAN & SWISS-FRENCH/GERMAN CHARACTER SET ° & ø Ø µ ¢ é É £ ÷ â ê Â Ê ¥ ä ë Ä Ë · © à è À È á í Á Í...
Page 370 Character Sets IBM EBCDIC CODEPAGES SUPPLIED Codepage Type Countries SBCS USA, Canada, Netherlands, Portugal, Brazil SBCS Austria, Germany SBCS Belgium (old) SBCS Denmark, Norway SBCS Finland, Sweden SBCS Italy SBCS Spain, Latin America (Spanish) SBCS SBCS Japanese - Katakana SBCS France DBCS Japanese - Kanji...
Page 371: Vt52 Emulation
Host Command Summary Host Command Summary This appendix lists the host commands that are valid in each terminal emulation mode. Additional special commands are listed at the back. The following conventions are used in this command list. Spaces in a command are for clarity only and are not to be entered as part of the command.
Page 372: Ansi Vt100 Emulation
Host Command Summary TEXT ERASURE Erase text to end of line ESC K Erase text to end of screen ESC J GENERAL Cancel current ESC sequence & display error Sound audible tone MODE SELECTION Select numeric keypad application mode ESC = Select numeric keypad normal mode ESC >...
Page 373 Host Command Summary Deselect underline character mode ESC [ < 1 h Double width & height (top half) characters ESC # 3 Double width & height (bottom half) characters ESC # 4 Double width single height characters ESC # 6 Select underline character mode ESC [ <...
Page 374: General Operation
Host Command Summary DISPLAY Scroll display down * lines ESC [ * T Scroll display up * lines ESC [ * S Select 80 column display mode ESC [ ? 3 l Select 132 column display mode ESC [ ? 3 h Select invisible display ESC [ ? 75 l Select normal colour display mode...
Page 375 Host Command Summary KEYBOARD Backspace key performs backspace only ESC [ ? 67 h Backspace key performs delete ESC [ ? 67 l Data processing keys mode ESC [ ? 68 h Disable key autorepeat ESC [ ? 8 l Disable keyboard ESC ` Disable keyboard input...
Page 376: Ansi Vt500 Emulation
Host Command Summary Print cursor line ESC [ ? 1 i Print page ESC [ i Print page prints complete page ESC [ ? 19 h Print page prints scrolling region only ESC [ ? 19 l REPORTS Report compatibility level ESC [ >...
Page 377 Host Command Summary DISPLAY Display host-writable status line ESC [ 2 $ ~ Display indicator status line ESC [ 1 $ ~ Display no status line ESC [ 0 $ ~ Send data to main display ESC [ 0 $ } Send data to status line ESC [ 1 $ } Display time on status line (*h = hour (24) *m = minutes)
Page 378 Host Command Summary PRINTING Enable bidirectional printing ESC [ 7 i Disable bidirectional printing ESC [ 6 i Enable printer/tablet to talk directly to host (one way) ESC [ ? 9 i Disable printer/tablet from talking directly to host ESC [ ? 8 i Destination port (only first * is parameter: 0 = None, 1 = LPT 1/2, 2 = COM 1, 3 = COM 2, etc.) ESC [ * * u...
Page 379: Ansi Vt420 Emulation
Host Command Summary ANSI VT420 Emulation When running the VT420 emulation, the following commands will be executed in addition those listed for ANSI VT100 and VT500. CURSOR MOVEMENT & PANNING Back index ESC 6 Forward index ESC 9 Pan down (*l = number of lines) ESC [ *l S Pan up (*l = number of lines) ESC [ *l T...
Page 380 Host Command Summary Local function key control ESC [ *k ; *f ; ... *k ; *f * } *k = Function key number: *f = Function performed: All local function keys Factory default F1 or Hold Local function F2 or Print Send key sequence 2 F3 or Set-Up Disable key...
Page 381 Host Command Summary Fill rectangular area ESC [ *f ; *t ; *l ; *b ; *r $ x *f Decimal code of fill character *b Bottom-line border *t Top-line border *r Right-column border *l Left-column border Selective erase rectangular area ESC [ *t ;...
Page 382: Ansi Vt510 Emulation
Host Command Summary ANSI VT510 Emulation When running the VT510 emulation, the following commands will be executed in addition those listed for ANSI VT100 and VT500. USER-DEFINED KEYS Download definitions for user-defined keys DCS *c ; *l ; *m | D...D ST *c 0 or none Clear all keys before loading new values (0 is default).
Page 383 Host Command Summary PROGRAMMING ALPHANUMERIC KEYS Program Alphanumeric Key(s) DCS " y D...D ST where the data string D...D format is as follows: Key1/Hex Code String/Function #/UDS/UDS Direction;Key2/...; Key# Is the key station number of the key to be programmed as listed below: Esc 110 Page Up 85 F1 112...
Page 384 Host Command Summary PROGRAMMING FUNCTION KEYS Program Function Key(s) DCS " x D...D ST where the data string D...D format is as follows: Key1/Mod1/Function #/UDS/UDS Direction; Key2/Mod2/Function #/UDS/UDS Direction;..; Key# Is the key station number of the key to be programmed as listed below: Page Up Page Down Cursor Left...
Page 385 Host Command Summary ANSI VT520 Emulation When running the VT520 emulation, the following commands will be executed in addition to those listed for ANSI VT100 and VT500. Note that an * (asterisk) before a command description indicates the command is accepted but not actioned. Sessions * Enable session CSI &...
Page 386: Colour Selection
Host Command Summary Colour Selection Assign colour CSI *i *f *b , | *i = Item Normal text Window frame 2 (not actioned) *f = Foreground colour index 0 - 15 *b = Background colour index 0 - 15 Alternate text colour CSI *a *f *b , } *a = Attribute Normal text...
Page 387 Host Command Summary Restore saved cursor (SCO) CSI u Set cursor style CSI * SP q * = Blinking block none, 0, 1 Steady block Blinking underline Steady underline Right-to-left copy enabled CSI ? 96 h Right-to-left copy disabled CSI ? 96 l Right-to-left mode enabled CSI ? 34 h Right-to-left mode disabled...
Page 388 Host Command Summary *c = character set as follows: Default 94-Character Set Default 96-Character Set Cyrillic (DEC) ISO Latin-1 Supplemental " ? Greek (DEC) ISO Latin-2 Supplemental " > Greek NRCS ISO Greek Supplemental " 4 Hebrew (DEC) ISO Hebrew Supplemental Hebrew NRCS ISO Latin-5 Supplemental Portuguese NRCS...
Page 389 Host Command Summary Swedish Norwegian Russian French Latin-American Key position mode set (key position) CSI ? 81 h Key position mode reset (char. codes) CSI ? 81 l North American/Greek selection set (North American) CSI ? 57 h North American/Greek selection reset (Greek keyboard) CSI ? 57 l Program alphanumeric key (for *...* see below) DCS "...
Page 390 Host Command Summary Request key type (* = decimal key station number) CSI * , u Report key type CSI *n ; *t , v *n = decimal key station number *t = key type: Alphanumeric key Function key Report function key definition (for *...* see below) DCS "...
Page 391 Host Command Summary Printer Media copy - send screen data CSI 2 i Select digital printed data type CSI * ) p * = Print National only none, 0, 1 National & Line Drawing Print Multinational Print all characters * Select printer type CSI * $ s * = DEC ANSI none, 0, 1...
Page 392 Host Command Summary Enter/exit VT PC Term mode / select ASCII or scancodes CSI ? *m ; *c r *m = VT mode or SCO ASCII/Scancodes as follows: VT Emulation Mode SCO Console Mode VT Mode ASCII characters none, 0 VT PCTerm Mode Scancodes *c =...
Page 393 Host Command Summary Status line type CSI * $ ~ * = No status line Indicator status line Host-writable status line 2 Communications Select communication port CSI *p ; *h * u *p = printer port: *h = host port: None Comm1 Centronics 1...
Page 394 Host Command Summary *s = characters per second: 150 cps none, 0, 1 50 cps 30 cps Transmit rate limiting mode set (limited) CSI ? 73 h Transmit rate limiting mode reset (unlimited) CSI ? 73 l Terminal Synchronization Disconnect delay time CSI * $ q * = delay time: None 60 ms...
Page 395: Aixterm Emulation
Host Command Summary AIXTerm Emulation All commands are supported in both VT100 and HFT (High Function Terminal) modes unless indicated otherwise. SINGLE BYTE CONTROLS Bell Backspace Horizontal tab Linefeed Vertical tab Form feed Carriage return Shift out Shift in Device control 1 Device control 3 Cancel Substitute...
Page 396 Host Command Summary Single shift G3 (VT100) ESC O Set G0 character set (HFT) ESC ( < Set G1 character set (HFT) ESC ) < Lock shift G2 (VT100) ESC n Lock shift G3 (VT100) ESC o COLOUR Set foreground & background colour ESC [ 2 ;...
Page 397 Host Command Summary Move cursor to line (*l) column (*c) ESC [ *l ; *c H Move cursor up * lines ESC [ * A Move cursor up * tabs (HFT) ESC [ * Y Restore cursor position ESC [ u Save cursor position ESC [ s DISPLAY...
Page 398 Host Command Summary Insert * blank lines ESC [ * L Insert * space characters ESC [ * @ GENERAL OPERATION Lock shift G2 ESC n Lock shift G3 ESC o Reset to initial state ESC c ANSI specified modes ESC [ *;...;* h IRM insert mode SRM send/rec mode (HFT)
Page 399 Host Command Summary PF key report (HFT) ESC [ * q Report cursor position ESC [ *l ; *c R Report terminal identity (host to VT100) ESC [ c Report terminal identity (host to VT100) ESC [ 0 c Terminal response (VT100 to host) ESC [ ? 1 ;...
Page 400 Host Command Summary AT&T 4410 Emulation CHARACTER ATTRIBUTES Normal ESC [ 0 m Dimmed ESC [ 2 m Underline ESC [ 4 m Flashing ESC [ 5 m Reverse video ESC [ 7 m Blanked ESC [ 8 m CURSOR Cursor down one line or * lines ESC [ B or ESC [ * B Cursor left one column or * columns...
Page 401 Host Command Summary BQ 3107 Emulation CHARACTER DISPLAY Blank area rendition Blink area rendition Select graphic rendition ESC [ * ; * ; * m Select G0, national or ASCII character set Select G1 graphic symbols character set Select G2 accented characters and special symbols set ESC E CURSOR Cursor addressing (1 to 80 = SP to g...
Page 402 Host Command Summary DG 410/412 Emulation DG Mode In the following command sequences, <n> represents a 1-byte argument, <nn> represents a 2-byte argument, and <nnn> represents a 3-byte argument. Bytes are entered as ASCII characters. Only the four least significant bits are used in each byte. Commands that are D100/200 compatible are indicated by an ◆.
Page 403 Host Command Summary Scroll down RS I Scroll up RS H Scroll left RS F C <n> Scroll right RS F D <n> Select compressed spacing RS F K Select normal spacing RS F J Set margins RS F X <nn><nn> Set alternate margins RS F Y <nn><nn><nn>...
Page 404 Host Command Summary DG 410/412 ANSI Standard Mode CHARACTER ATTRIBUTES Change attributes CSI *count ; *on ; *off q CURSOR Backspace Carriage return Cursor left * columns CSI * D Cursor right * columns CSI * C Cursor down * lines CSI * B Cursor up * lines CSI * A...
Page 405 Host Command Summary HP 700-92/96 Emulation CHARACTER ATTRIBUTES Assign * attribute(s) to following characters ESC & d * Assign invisible & * attribute(s) to following chars. ESC & d s * Dim, Flash & Underline M Flashing Dim, Under & Inverse Inverse video Dim, Flash, Und.
Page 406 Host Command Summary DISPLAY 80 column display ESC & w 6 f 80 X 132 column display ESC & w 6 f 132 X Clear all margins ESC 9 Display next page ESC U Display previous page ESC V Format mode off ESC X Format mode on ESC W...
Page 407: Function Keys
Host Command Summary FUNCTION KEYS Begin user key definition mode ESC j Default definition for f1 key ESC p Default definition for f2 key ESC q Default definition for f3 key ESC r Default definition for f4 key ESC s Default definition for f5 key ESC t Default definition for f6 key...
Page 408 Host Command Summary KEYBOARD Auto keyboard lock off ESC & k 0 K Auto keyboard lock on ESC & k 1 K Auto line feed mode off ESC & k 0 A Auto line feed mode on ESC & k 1 A Caps lock off ESC &...
Page 409 Host Command Summary IBM 3151 Emulation CHARACTER SET SELECTION Select G0 Select G1 Select character set G0 ESC < *set Select character set G1 ESC > *set CURSOR Backspace Carriage return, new line or LTA Cursor down ESC B Cursor left ESC D Cursor right ESC C...
Page 410 Host Command Summary Enable host protect ESC & : Enable OIA divide line ESC * : Enable read unprotected field ESC % : Host message write ESC = *message ESC = Host message display ESC # ; Set character attribute ESC 4 *attrib *operation Set field attribute ESC 3 *attrib *attrib *operation...
Page 411 Host Command Summary Read status ESC 6 Enter transparent mode (control characters displayed) DLE STX Exit transparent mode DLE ETX Mandatory disconnect DLE EOT Begin pass-through data stream DLE DC2 End pass-through data stream DLE DC4 Restart transmission (pacing) DC1 (XON) Stop transmission (pacing) DC3 (XOFF) Begin outbound trace...
Page 412 Host Command Summary MDIS Prism-8 & Prism-9 Emulations CHARACTER SET SELECTION Assign G0 label to * character set ESC ( * Assign G1 label to * character set ESC ) * Assign G2 label to * character set ESC * * (second * is parameter) Assign G3 label to * character set ESC + * Assign G0 labelled set to 7 bit codes...
Page 413 Host Command Summary Set tab stops at specified * column numbers ESC [ *c ; *c ; ..*c SP N Clear tab stops (0 = at cursor position, 2 & 3 = all on page) ESC [ * g Set tab stop at current cursor position ESC [ 0 W Clear tab stops (2 = at cursor position, 4 &...
Page 414 Host Command Summary Bold, Flashing, Inverse & Underline attributes ETX W Blank & Underline attributes ETX X Bold, Blank & Underline attributes ETX Y Flashing, Blank & Underline attributes ETX Z Bold, Flashing, Blank & Underline attributes ETX [ Inverse, Blank & Underline attributes ETX \ Bold, Inverse &...
Page 415 Host Command Summary Move cursor to start of next line ESC E Move cursor up one line ESC M Move cursor to start of new page Move cursor one column left Repeat last displayable character * times (default 1) ESC [ * b KEYBOARD Key presses generate codes which are sent to host ESC [ 2 l...
Page 416 Host Command Summary where *o = output type as listed below, default 0 0 = print page, 1 = print partial page, 2 = hardcopy off 3 = hardcopy on, 4 = direct print off, 5 = direct print on *s = starting line number, default start of scrolled region *e = ending line number, default end of scrolled region Media copy...
Page 417: System Messages
Host Command Summary *c = number of columns displayed (80 or 132) *g = general status (1 = multiple active page format, 2 = per-character attributes) Printer status report (*g = general status, *b = buffer left) ESC [ < 12 ; *g ; *b n Keyboard status report (*m = mode, *g = general status) ESC [ <...
Page 418 Host Command Summary Set S-mode Hex E1 Cursor on Hex E2 Start of system message Hex E3 * Cursor off Hex E4 End of system message Hex E5 Give terminal status Hex E6 Set screen format Hex E7 * Display system message Hex E8 Display user line 25 Hex E9...
Page 419 Host Command Summary PT250 Emulation AREA & LOGICAL ATTRIBUTES Assert defined logical attributes ESC [ > 3 h Assert defined logical attributes disabled ESC [ > 3 l Clear (reset) selected areas ESC $ K Define area qualification ESC [ * o * = All printing characters Numeric characters Alphabetic characters...
Page 420 Host Command Summary CURSOR Autowrap disabled ESC [ > 9 h Autowrap enabled ESC [ > 9 l Carriage return = carriage return only ESC [ > 1 l Carriage return = carriage return & line feed ESC [ > 1 h Cursor invisible ESC $ S Cursor movement keys immediate effect...
Page 421 Host Command Summary Display system line (data on line preserved) ESC $ U Display system line (blank) ESC $ V Display visible ESC $ P Jump scroll enabled ESC [ > 5 l Lock lines (*l = screen line number to begin, *n = # of lines) ESC [ *l ; *n u Next page (* = 1 page one, 2 page two) ESC [ * U Page down...
Page 422 Host Command Summary Read cursor character ESC ; Read cursor character normal mode ESC [ > 23 l Read cursor character erase mode ESC [ > 23 h GENERAL OPERATION Action all control characters except CR & HT ESC [ > 14 h Action all control characters including CR &...
Page 423 Host Command Summary LOCAL EDITING Data block is cursor line ESC [ > 4 h Data block is page(s) (depends on display memory) ESC [ > 4 l Dump block data ESC 6 Enter character mode ESC [ > 2 l Enter edit (block) mode ESC [ >...
Page 424 Host Command Summary Change visual attributes of line ESC [ * t * = Active position to end of line Start of line to active position Entire line Select graphic rendition ESC [ * m Normal video Strike-through > 1 Dimmed Invisible >...
Page 425: Regis Emulation
Host Command Summary ReGIS Emulation MODE SELECTION Exit to VT100/VT200 mode ESC \ MOUSE BUTTON PROGRAMMING Program a mouse button (*c = clear, *b = button, ESC P *c $ w *b/*p/*r ESC \ *p = press code, *r = release code) SIXEL GRAPHICS Direct sixels to host ESC [ ? 2 i...
Page 426 Host Command Summary LOADING CHARACTER SETS Assign name to set currently selected for loading L(A ' set name ') Select set for loading & assign name L(A set number ' set name ') Select specified character set for loading L(A set number ) Specify character form in hex codes &...
Page 427 Host Command Summary TEXT DISPLAY Select 1 of 17 standard sets of char. cell, character matrix & char. cell spacing T(S standard set ) Select character cell size T(S[ cell width , cell height ]) Select character cell & matrix height multiplier T(H cell &...
Page 428: Sco Console Emulation
Host Command Summary SCO Console Emulation CONTROLLING TERMINAL PROCESSING Sound audible tone Select iBCSe2 compliance ESC [ = 2 L Deselect iBCSe2 compliance ESC [ = 3 L Save cursor position ESC 7 Restore cursor position ESC 8 KEYBOARD FUNCTIONS Disable keyboard input ESC [ 2 h Enable keyboard input...
Page 429 Host Command Summary Set inverse & foreground & background colour (* as above) ESC [ 7 ; *fg ; *bg ; m Set normal foreground colour (* = integer as above) ESC [ = * F Set normal background colour (* = integer as above) ESC [ = * G Set reverse foreground colour (* = integer as above) ESC [ = * H...
Page 430 Host Command Summary EDITING Erase from cursor to end of display ESC [ 0 J Erase from start of display to cursor ESC [ 1 J Erase entire display ESC [ 2 J Erase from cursor to end of line ESC [ 0 K Erase from start of line to cursor ESC [ 1 K...
Page 431 Host Command Summary Siemens 97801 Emulation CHARACTER SET SELECTION Assign International character set to G0 ESC ( @ Assign International character set to G1 ESC ) @ Assign International A character set to G0 ESC ( B Assign International A character set to G1 ESC ) B Assign German character set to G0 ESC ( K...
Page 432 Host Command Summary Save cursor position ESC [ s Move cursor to last saved position ESC [ u DISPLAY AREA MOVEMENT Roll mode (do not destroy data) ESC [ 10 u Scroll mode (destroy data) ESC [ 11 u Move display up * lines ESC [ * S Move display down * lines ESC [ * T...
Page 433 Host Command Summary Sound bell Key click disabled ESC [ 2 s Key click enabled ESC [ 3 s Report keyswitch status ESC [ 0 w Map scan codes corresponding to German keyboard values ESC [ 7 u Map scan codes corresponding to all other keyboard values ESC [ 6 u Load more national keyboards ESC R A ...
Page 434 Host Command Summary TA6530 Emulation Conversational & Block Mode ATTRIBUTES Set display attribute * ESC 6 * Normal video Inverse invisible Dimmed Underline dim Inverse video Underline italics Italics " Underline inverse Invisible Underline inverse dim Underline Underline inverse italics Inverse dim Underline invisible Inverse italics...
Page 435 Host Command Summary Select page * (Block mode) ESC : * Set current line to 40 (double width) columns ESC 8 Set current line to 80 (single width) columns ESC 9 Set max. number of pages for display (Block mode) ESC p * Set page size to 24 lines by 40 characters ESC t...
Page 436: Ansi Mode
Host Command Summary KEYBOARD Define Return key (Conversational mode) ESC u * Lock keyboard ESC c Unlock keyboard ESC b Simulate function key ESC d * REPORTS Report cursor address ESC a Report emulation status ESC ^ Report firmware revision level ESC _ ANSI Mode CHARACTER SETS...
Page 437 Host Command Summary DISPLAY Insert * spaces at cursor location ESC [ * @ Restore cursor position & video attribute ESC 8 Save cursor position & video attribute ESC 7 Set current line to single width (80 columns) ESC # 5 Set current line to double width (40 columns) ESC # 6 Scroll display down * lines...
Page 438: Tek 4010/4014 Emulation
Host Command Summary Tek 4010/4014 Emulation ALPHANUMARIC MODE Select G0 character set for alpha text ESC SI Select G1 character set for alpha text ESC SO CURSOR MOVEMENT Move cursor down 1 pixel ESC \ b Move cursor down 16 pixels ESC \ B Move cursor left 1 pixel ESC \ d...
Page 439 Host Command Summary Select Graphics Text mode Select Graphics Text mode Select Graphics Text mode ESC FF Select Incremental Point mode Select Point mode Select Vector mode Select Vector mode ESC \ GS VECTOR MODE Clear Vector mode screen ESC \ FF Deselect write-through &...
Page 440: Tvi 955 Emulation
Host Command Summary TVI 955 Emulation GENERAL OPERATION Block mode on ESC B Local mode on ESC c Half duplex mode on ESC D H Full duplex mode on ESC D F Return to previous conversational mode ESC C Set terminal operating mode(s) (0 = 955, 1 = 950) ESC [ = * h Reset terminal operating mode(s) (0 = 955, 1 = 950) ESC [ = * l...
Page 441: Editing Modes
Host Command Summary Read cursor's page, line & column position ESC / Read cursor's line & column position in decimal units ESC [ 6 n Read cursor's page, line & column position in decimal units ESC [ ? 6 n DISPLAY Turn screen on ESC n...
Page 442: Editing Data
Host Command Summary EDITING DATA Enable page edit mode ESC N Enable line edit mode ESC O Enable insert mode ESC q Enable replace mode ESC r Load a replacement character ESC e * Insert a replacement character at cursor position ESC Q Insert * replacement characters at cursor position ESC [ * @...
Page 443 Host Command Summary Additional *1 values: <space> Clear entire current function key set from memory Load function keys in sequence *2 message destination values: Send message to host Send message to terminal Send message to both host and terminal Save function key reprogramming in non-volatile memory ESC [ = 10 h Do not save function key reprogramming in non-volatile memory ESC [ = 10 l...
Page 444 Host Command Summary User Message Effect *m = Status line message field *e = Clears message before loading User message 1 Writes over existing message User message 2 Send contents of information line ESC Z * * = 0 User message 1 Status line User message 2 PRINTING...
Page 445 Host Command Summary Send unprotected characters in cursor line up to & including cursor ESC 4 Send unprotected page up to & including cursor ESC 5 Send entire cursor line characters up to & including cursor ESC 6 Send entire page up to & including cursor ESC 7 Send unprotected message between start of text and end of text ESC S...
Page 446 Host Command Summary Unisys T27 Emulation FORM OPERATIONS Set forms mode ESC W Reset forms mode ESC X Toggle forms mode Exit forms mode SEARCH OPERATIONS Set search mode ESC E Set search character (if 80 hex or less) ESC - * Set search character (if greater than 80 hex) ESC - ESC SO * ESC SI Reset search mode...
Page 447 Host Command Summary VIDEO ATTRIBUTE SEQUENCES Underline video highlight ESC 3 Reverse video highlight ESC 4 End highlight Start video blink Start secure video Start bright video Set reverse video ESC N Set normal video ESC O TERMINAL RECONFIGURATION SEQUENCES Store ASCII codes as data ESC R A *start *length *data ESC R C Configure Data Comm, Screen &...
Page 448 Host Command Summary Viewdata Mode COLOUR SELECTION Background cell colour = previous character colour ESC ] Cell background colour black (default) ESC \ Select blue alphanumeric character set ESC D Select blue graphics character set ESC T Select cyan alphanumeric character set ESC F Select cyan graphics character set ESC V...
Page 449 Host Command Summary VT640 Emulation ALPHANUMARIC MODE Select G0 character set for alpha text ESC SI Select G1 character set for alpha text ESC SO CURSOR MOVEMENT Move cursor down 1 pixel ESC \ b Move cursor down 16 pixels ESC \ B Move cursor left 1 pixel ESC \ d...
Page 450 Host Command Summary MODE SELECTION Select Alphanumeric mode Select Alphanumeric mode Select Alphanumeric mode ESC \ CAN Select GIN mode ESC SUB Select GIN mode ESC " 4 g Select GIN mode ESC " 5 g Select Graphics Text mode Select Graphics Text mode Select Graphics Text mode ESC FF...
Page 451 Host Command Summary W2119 Emulation ALPHANUMARIC MODE Select G0 character set for alpha text ESC SI Select G1 character set for alpha text ESC SO CURSOR MOVEMENT Move cursor down 1 pixel ESC \ b Move cursor down 16 pixels ESC \ B Move cursor left 1 pixel ESC \ d...
Page 452 Host Command Summary MODE SELECTION Select Alpha mode & erase alpha memory ESC EOT Select Alphanumeric mode Select Alphanumeric mode Select Alphanumeric mode ESC 2 Select Alphanumeric mode ESC \ CAN Select GIN mode ESC SUB Select Graphics Text mode Select Graphics Text mode Select Graphics Text mode ESC 1...
Page 453 Host Command Summary Wyse Emulations ATTRIBUTES Assign character display attribute ESC G *attribute Assign line attribute ESC G *line attribute Assign write-protected character attribute ESC ' *attribute Line attribute mode on ESC e 3 Page attribute mode on ESC e 2 Wyse 60 character attribute mode on ESC e 1 Wyse 60 character attribute mode off...
Page 454 Host Command Summary Clear unprotected page to nulls ESC : Clear unprotected page to nulls from cursor ESC y Clear unprotected page foreground to nulls from cursor ESC c Q Clear unprotected page to spaces ESC ; or SUB Clear unprotected page to spaces from cursor ESC Y Clear unprotected page foreground to spaces from cursor ESC c P...
Page 455 Host Command Summary Cursor right Cursor up (no scroll) Cursor to start of current line Cursor to start of next line Home cursor ESC { or RS Line lock mode on ESC ` H Line lock mode off ESC ` I Move cursor up;...
Page 456: Host Communications
Host Command Summary Restore normal display ESC ^ 0 Reverse display ESC ^ 1 Roll window up in page ESC w E Roll window down in page ESC w F Split screen ESC x C *line Split screen (two pages only) ESC x A *line Split screen &...
Page 457: Keyboard Functions
Host Command Summary Enhance mode on ESC ~ ! Enhance mode off ESC ~ SP Monitor mode on (display control codes) ESC U Monitor mode off ESC u or ESC X Block mode on ESC B Half-duplex mode on ESC C ESC D H Half-duplex block mode on ESC D H ESC B Full-duplex mode on...
Page 458 Host Command Summary Bidirectional mode on ESC d % Enable transmission (XON/XOFF handshaking) DC1 (XON) Stop transmission (XON/XOFF handshaking) DC3 (XOFF) Mark block beginning ESC 8 Mark block end ESC 9 Print entire formatted page ESC P Print formatted unprotected page ESC @ Print unformatted page ESC p or ESC L...
Page 459: Wyse Pc Term Emulation
Host Command Summary Wyse PC Term Emulation MONITOR MODE Monitor mode on ESC U Monitor mode off ESC u or ESC X SELECTING PERSONALITIES Enhance mode off ESC v SPACE Enhance mode on ESC v ! Select WYSE 50+ personality ESC v "...
Page 460: Programming Keys
Host Command Summary CAPS LOCK on (enhanced) ESC e & CAPS LOCK off (enhanced) ESC e ' Margin bell off ESC n Margin bell on ESC o Select standard ASCII key code mode ESC e H Select PC scan code mode ESC e I Key repeat off (enhanced) ESC e ,...
Page 461 Host Command Summary CURSOR CONTROL Cursor left (backspace) CTRL H Cursor right CTRL L Cursor up - no scroll CTRL K Cursor up - scroll ESC j Cursor down - no scroll CTRL V Cursor down - scroll CTRL J Cursor to start of line CTRL M Cursor to start of next line...
Page 462 Host Command Summary SENDING DATA Send line through cursor ESC 6 Send unprotected line through cursor ESC 4 Send page through cursor ESC 7 Send unprotected page through cursor ESC 5 Mark block beginning ESC CTRL B Mark block end ESC CTRL C Send entire block ESC s...
Page 463 Host Command Summary Assign foreground/background colours ESC SPACE h *CGAcol Assign fore/background colours to write-protected chars ESC SPACE i *CGAcol Assign foreground colours to write-protected chars ESC SPACE j *fc370 Assign background colours to write-protected chars ESC SPACE k *fc370 Assign display attribute to write-protected characters ESC SPACE 1 *assattr 370/350 COLOUR MISCELLANEOUS...
Page 464: Additional Commands
Host Command Summary Additional Commands DISPLAY COLOUR DEC VT modes: Foreground colour CSI = * F Background colour CSI = * G where * is one of the following numbers: Black Grey 12 Light Red Blue Magenta Light Blue 13 Light Magenta Green Brown 10 Light Green...
Page 465 Host Command Summary <Button Status> is of the format: 00110LMR where LMR indicates which button caused the event. <Column> and <Row> are the alphanumeric position of the mouse. REPORTS Report application name & version (in DEC VT modes) ESC [ 0 ; 1234 c C-95...
Page 466 Host Command Summary Notes C-96...
Page 467: Product Specification
Product Specification Product Specification This appendix describes the level of support provided by each terminal emulation. Introduction The following sections describe the level of support provided by each terminal emulation throughout the product range. Note that your product version may not support all the terminal emulations listed here.
Page 468 Product Specification Telnet Specification: Implements RFC 854, 855, 856, 857, 858, 860, 1091, 1408, 1571, 1572. Implements RFC 1205, 2877 for IBM 5250. Implements RFC 2355, 1576, 1646, 1647 for IBM 3270. AixTerm Limitations: No Vertical tab stops. No Select Alternate presentation variant. No Select reversed string.
Page 469: Digital Vt Emulation
Product Specification Data General D200/D410 Specification: Dasher D410 Display Terminals User’s Manual (014-000761-02 December 1983). Digital VT Emulation Specification: Digital VT 420 Programmer's Manual (EK-VT420-RM-001). Limitations: The DEC Multisession and SSU protocols are not implemented. HP 700/92 Emulation Specification: HP 2392A Reference Guide (02394-90001. April 1984). IBM 3270 Emulation Specification: 3270 Information Display System Data Stream Programmer's Reference...
Page 470 Product Specification IBM 5250 Emulation Specification: 5494 Remote Control Unit Functions Reference. Release 2.0. (SC30-3533-02). Limitations: No text assist in Right to Left writing mode. No double-byte printing. The 3812-1 Non Host Print Transform (Non-HPT) print protocol is not supported. No Calculator / Hex key.
Page 471: Stratus V102
Product Specification Stratus V102 Specification: V102 Display Terminal Operator’s Manual (TVI 131974-00 June 1985). Limitations: Page print flip mode not supported. Serial configuration commands not supported. Select character set commands not supported. Tandem 6526/6530 Emulation Specification: Tandem 653x Multi-Page Terminal Programmer’s Guide (82310-B00 December 1983).
Page 472: Televideo 955
Product Specification Televideo 955 Specification: Televideo 955 Display Terminal Operator's Manual (131969-00-B Sept 1985). Limitations: Page print flip mode not supported. Serial configuration commands not supported. Select character set commands not supported. Unisys T27 Specification: Burroughs T27 Programmer’s Reference Manual (1196904 Aug 1986). Limitations: Print protocol, printer sessions and auxiliary i/o are not supported.
Page 473 Product Specification Function key label save commands not supported. Automatic font loading not supported. Remote caps lock commands not supported. Ignore nulls commands not supported. Attribute overwrite mode not supported. Disable intensity commands not supported. Some select personality commands not supported. Wyseword mode not supported.
Page 474 Product Specification Notes...
Page 475 Index Index Symbols Status bar 8-3 Virtual key names A-2 4010/4014 Emulation Buffer Rows 6-76 Screen mapping 6-90 Button Tools Settings menu 6-89 Predefined functions (XPe) 5-1 Redefining (XPe only) 5-3 Windows CE 2-42 Windows XPe 2-45 AIXTerm Emulation Host command summary C-25 Specification D-2 Answerback String 6-29 Character Set Selection 6-77...
Page 476 Index Codes In Setup Entries 6-4 Replay) 20-8 Enable Debug Log Send & Colour Attributes 6-92 Receive 20-8 Colour Selection Enable plane masking 20-19 Line styles 6-92 Flashing for all sessions 20-17 Text attributes 6-92 Graphics redraw on resize 20-17 Command Bar (CE) 2-41 New session warning message 20-5 Preload Winsock DLL for PPP...
Page 477 Index Status line DEC VT emulations 7-4 DEC Multinational Set 6-77 IBM 3151 emulation 13-3 IBM 3270 emulation 11-5 DEC VT Emulations IBM 5250 emulation 12-5 Horizontal scrolling 7-5 Wyse emulations 19-4 Keyboard mapping 7-5 Specification D-3 Status bar 7-4 Default Setup Settings 6-4, 6-9 Edit Menu 6-23 DG 410/412 Emulation...
Page 478 Index Host Information Connection Wizard 2-2 GUI Overrides Hotspots Connection Wizard 2-36 Displaying all 2-47 Using 2-47 HP 700-92/96 Emulation Configuration selection 10-8 Hebrew Language Device control 10-8 Typing direction (DEC suite) Display attributes 10-16 6-77, 6-78, 7-8 Function keys & labels 10-3 Host Command Summary Host command summary C-35 AIXTerm emulation C-25...
Page 479 Index Swedish B-38 Fax image support 12-11 Swiss-French B-39 Introduction 12-1 Swiss-German B-39 Keyboard mapping 12-6 Close key 11-9 National character settings 6-58 Display right-to-left 11-9 Push mode 12-8 Display rule 6-51 Record/playback keystrokes 12-9 Introduction 11-1 Selecting 12-1 Keyboard mapping 11-10 Session configuration 12-1 National character settings 6-52 Setup 6-56...
Page 480 Index MDIS Prism functions 14-4 Mouse PT250 functions 15-6 Button tools 6-105 Siemens 97801 functions 16-4 GIN Button definitions 6-91 TA6530 functions 17-6 Middle button emulating 4-3 Unisys T27 functions 18-5 Mouse Functions 6-103 Wyse functions 19-6 Action hotspots 4-3 Entering control characters B-1 Default 4-1 Keypad mode 6-79...
Page 481 Index PT250 Emulation Disable Tools menu 20-15 Character sets Enable plane masking 20-19 Additional B-23 Graphics redraw on resize 20-17 Block Graphics B-25 New session warning message 20-5 Line Drawing B-24 Reflection 4 colour support 20-17 Displaying alternate characters 15-7 Save 4014 graphics display 20-18 Host command summary C-49 Set Tek graphics height 20-18...
Page 482 Index IBM 3270 emulation 11-1 Startup options 6-15 IBM 5250 emulation 12-1 TA6530 settings 6-48 MDIS Prism emulations 14-1 Tab Stops 6-82 PT250 emulation 15-1 Tek 4014 settings 6-89 Siemens 97801 emulation 16-1 Terminal settings 6-75 TA6530 emulation 17-1 Unisys T27 settings 6-61 Unisys T27 emulation 18-1 Wyse settings 6-43 Wyse emulations 19-1...
Page 483 Index DEC VT emulations 7-4 Terminal Settings 6-75 Unisys T27 emulation 18-3 Terms & Conventions 1-3 Status Line TN3270 Options 2-11 DEC host writable 6-76 TN5250 Options 2-13 IBM 3151 emulation 13-3 Toolbar IBM 3270 emulation 11-5 Predefined button tools (XPe) 5-1 IBM 5250 emulation 12-5 Redefining (XPe only) 5-3 PT250 emulation 15-3...
Page 484 Index IBM 5250 Word Processing A-5 Screen mapping 6-90 Insert delay A-11 Window Elements MDIS Prism emulations A-6 Status line PT250 emulation A-6 PT250 emulation 15-3 Reading text from a file A-11 Wyse 60 Native Emulation SCO Console emulation A-7 Specification D-6 Serial port functions A-10 Wyse Emulations...

This manual is also suitable for:

Neoware e140 - thin client Neoware e370 - thin client Neoware e90 - thin client Neoware m100 - mobile thin client Teemtalk 5.0

Neoware c50 - Thin Client User Manual

Introduction

Initialization Commands

T

Getting Started

Keyboard Configuration

Mouse Functions

The Toolbar

Setup Menus

DEC VT Emulations

BQ 3107 Emulation

DG 410/412 Emulation

HP 700-92/96 Emulation

IBM 3270 Emulation

IBM 5250 Emulation

IBM 3151 Emulation

MDIS Prism Emulations

PT250 Emulation

Siemens 97801 Emulation

TA6530 Emulation

Unisys T27 Emulation

Wyse Emulations

Quick Links

Related Manuals for Neoware Neoware c50 - Thin Client

Summary of Contents for Neoware Neoware c50 - Thin Client