Advertisement
About the storage drawers,
gecom
Not aft features are on all models.
Snacks Drawer
The snacks drawer can be moved to tim
most useflfl location for your family's
needs.
About storage drawer and cover removal.
Not all features are on all models.
Humidity
Control
HIGH
LOW
Adjustable Humidity Drawer (onsomemodels)
Slide
the
control
all die
way to the
Slide
the
control
all die
way to the
LOW
HIGHsetdng to provide high humidity
setting to provide lower humidity levels
recommended
for most vegetables,
recommended
for most fl_uits.
Drawer and Cover Removal
Drawers can be removed easily by grasping the sides and lifting tap slighdy while pulling
drawers past the stop location.
Full-Width
Drawer
with
Plastic Cover
Toremove the cover,lift it off its supports,
pull it forward, tilt it and rake it out.
Twin Drawer Shelf
Toremove:
[-'7] Remove
tile drawers.
[_-] Reach in, push the flont of glass cover
up, and at tile same time, pull it forward
as far as it will come.
Tilt it and take it out. Avoid cleaning the cold
glass covet" with hot water becmlse the exu'eme
temperature
ditference
mW cause it m break.
[-_] Remove
tile drawer
fl_une. (Always
remove
tile ,glass cover before
you rake
out the drawer
fiame.)
Lift the fi'mne off the supports
at each side
and back, pull it forward,
flit it and take it out.
Toreplace:
F_ Lower the frame until it rests on the
supports at each side and back.
[_--]Replace tile glass covet; pushing its rear
edge firmly into the rear flame channel
and gendy lowering tile flont into place.
[j] Replace tile drawers.
About the automatic icemaker.
A newly-installed
refrigerator may take 12 to 24 hours to begin making ice.
ij)(( j ¸/i/
,qerArmin
le STOP
Feeler A rmin (Up)position
the ON (down)
position
Automatic Icemaker (on some models)
The icemaker will produce approximately
100-130 cubes in a 24-hour period,
depending on the fl'eezer compai'unent
temperature, room temperature, number of
door openings mad other ttse conditions.
If the refl'igeramr is operamd before the
water
connection is made
to the
icemaket; move tile
feeler arm to the
STOP
(up) position.
When the refrigerator
has been connecmd
m the wamr supply, move tile feeler am1 m
the ON (down) position.
You will hear a buzzing sound each time
the icemaker fills with wamt.
The icemaker will fill with water when it cools
to 15°E A newly-installed refi'igerator mW rake
12 m 24 hours to begin making ice cubes.
Throw away the fi_t few batches of ice m
allow the wamr line m cleat.
Be sure nothing inmrferes with the sweep
of the feeler arm.
When the bin fills m the level of the feeler
arm, the icemaker will stop producing
ice.
It is normal for several cubes m be joined
together.
If ice is not used fiequendy, old ice cubes
will become cloudy, tasm stole and shrink.
NOTE: In homes with lower-than-average water
pressure, youmayheartheicemaker c yclemultiple
timeswhenmaking onebatchof ice.
Icemaker Accessory Kit
If your refi'igerator
did not ah'eady come
equipped
with an mltomafic icemaket;
an
icemaker
accesso W kit is available at extra cost.
Check the back of the refligerator
for
tile specific icemaker
kit needed
for
your model.
5
Advertisement
