System Selector; To Display Pictures Complying With The Srgb Standard; Note - Panasonic PT-DS100XE Operating Instructions Manual

PICTURE menu

SYSTEM SELECTOR

This enables the projector to automatically recognize
input signals. Furthermore, if unstable signals are
input, the system format can be selected manually.
1 ) Press ▲▼ to select [SYSTEM
SELECTOR].
2 ) Press <ENTER> button.
3 ) Press ▲▼ to switch [SYSTEM
SELECTOR].
4 ) Press <ENTER> button.
VIDEO/S-VIDEO terminal input
J
signal
Select from AUTO, NTSC, NTSC4.43, PAL,
PAL-M, PAL-N, SECAM, and PAL60.
Attention
[AUTO] mode is selected by default.
z
When the projector is not working properly in [AUTO]
z
mode, change the setting according to each SYSTEM
SELECTOR type.

Note

[AUTO] automatically selects from NTSC, NTSC4.43,
z
PAL, PAL-M, PAL-N, SECAM, and PAL60.
RGB1/RGB2 terminal input signal
J
480i, 576i, 576p signals
z
Select from RGB and YC
VGA60, 480p signals
z
Select from VGA60, 480p, and 480pRGB.
Other signals
z
Select from RGB and YP
Note
Refer to "List of compatible signals" (
z
available signals.
DVI-D terminal input signal
J
480p, 576p signals
z
Select from RGB and YC
Other signals
z
Select from RGB and YP
Note
Refer to "List of compatible signals" (
z
available signals.
Malfunction may occur or other problems could be
z
encountered with some equipment.
58
- ENGLISH
C .
B R
P .
B R
Æ page 123) for
C .
B R
P .
B R
Æ
page 123) for
HDMI terminal input signal
J
480p, 576p signals
z
Select from Auto, RGB, and YC
Other signals
z
Select from Auto, RGB, and YP
Note
Refer to "List of compatible signals" (
z
available signals.
Malfunction may occur or other problems could be
z
encountered with some equipment.
SDI terminal input signal
J
(PT-DZ110XE/PT-DS100XE only)
Select from AUTO, 1 080/60i, 1 035/60i,
z
720/60p, 1 080/24p, 1 080/50i, 1 080/30p,
1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i.
Refer to "List of compatible signals"
z
( Æ page 123) for available signals.
To display pictures complying
with the sRGB standard
sRGB is the international color reproduction standard
(IEC61966-2-1) established by IEC (International
Electrotechnical Commission).
To reproduce colors more faithfully in compliance
with the sRGB standard, perform the following setting
procedure.
1 ) Set [COLOR MATCHING] adjustment to
[OFF].
Refer to "COLOR MATCHING"
z
2 ) Display the [PICTURE] screen.
Refer to "PICTURE menu" (
z
3 ) Press ▲▼ to select [PICTURE MODE].
4 ) Press ◄► to select [NATURAL].
5 ) Press ▲▼ to select [COLOR].
6 ) Press <DEFAULT> button on the
remote control to restore the factory
default.
7 ) Follow the same procedure (steps
5-6) to restore the factory default for
[TINT], [COLOR TEMPERATURE] and
[GAMMA].
Note
sRGB is only enable when RGB signals are being input.
z
C .
B R
P
B R
Æ
page 123) for
Æ
( page 69).
Æ page 53).