Page 26
PIN 1 P4U800-X ® P4U800-X IDE connectors P4U800-X FLOPPY1 PIN 1 ® NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. P4U800-X Floppy disk drive connector 1-16...
Page 27
ATXPWR1 ATX12V Pin 1 +12V DC +12.0VDC +5.0VDC +5VSB +5.0VDC PWR_OK -5.0VDC P4U800-X +5.0VDC +12V DC +5.0VDC PS_ON# +3.3VDC -12.0VDC ® +3.3VDC +3.3VDC P4U800-X ATX power connectors CD (Black) AUX (White) P4U800-X ® P4U800-X Internal audio connectors 1-17...
Page 28
CPU_FAN1 P4U800-X CHA_FAN1 ® P4U800-X Fan connectors P4U800-X ® USB56 P4U800-X USB 2.0 connector 1-18...
Page 29
FP_AUDIO P4U800-X MIC2 AGND MICPWR +5VA BLINE_OUT_R Line out_R ® Line out_L BLINE_OUT_L P4U800-X Front panel audio xonnector P4U800-X CHASSIS1 ® (Default) P4U800-X intrusion connector 1-19...
Page 30
P4U800-X GAME P4U800-X Game connector Speaker Connector Power LED P4U800-X Reset SW IDE_LED ® ATX Power Switch* P4U800-X System panel connector Requires an ATX power supply. • 1-20...
Page 45
IDE Primary Master Select Menu Item Specific Help IDE Auto-Detection [Press Enter] Enter the value. IDE Primary Master [Manual] Access Mode [CHS] Capacity 40020 MB Cylinder [19158] Head Sector 255] Transfer Mode UDMA 2 : Help : Select Item : Change Value F5 : Setup Defaults ↑...
Page 47
CPU Type Intel Pentium(R) 4 Select Menu CPU Speed 2.40GHz CPU Cache RAM 512K Item Specific Help Current FSB Frequency 533MHz Current DRAM Frequency 333MHz USB Legacy Support [Enabled] USB 2.0 Controller [Enabled] Init Display First [PCI Slot] Frequency/Voltage Control Chip Configuration I/O Device Configuration PCI Configuration...
Page 48
Frequency/Voltage Control Select Menu CPU Clock Ratio [17 X] Item Specific Help CPU/MEM Clock Selectable [Auto] x CPU Clock Setting [100] Sets the ratio between x MEM Clock Setting [DDR266] CPU core clock and Spread Spectrum [+/- 0.7%] the FSB frequency. : Help : Select Item : Change Value...
Page 49
Select Menu Chip Configuration Item Specific Help CAS Read Latency [Auto (By SPD)] Current CAS Latency Set the latency DRAM Performance [Auto (By SPD)] between the DRAM x DRAM Timing tRP command and the time x DRAM Timing tRAS the data actually x DRAM Timing tRCD becomes available.
Page 51
I/O Device Configuration Select Menu Item Specific Help Onboard Serial Port 1 [3F8/IRQ4] Onboard Parallel Port [378/IRQ7] Press [Enter] to select Parallel Port Mode [SPP] the I/O address & IRQ x ECP Mode USE DMA for COM1. EPP Mode Select [EPP1.7] Onboard AC97 Audio [Enabled]...
Page 52
Select Menu PCI Configuration Item Specific Help Onboard LAN Boot ROM [Disabled] Enable/Disable the Resources Controlled By [Auto (ESCD)] onboard SATA. x IRQ Resources PCI/CGA Palette Snoop [Disabled] Assign IRQ for VGA [Enabled] Assign IRQ for USB [Enabled] PCI Latency Timer (CLK) [ 64] PCI IRQ Actived By [Level]...
IRQ Resources Select Menu IRQ Resources Item Specific Help IRQ-3 assigned to [PCI Device] IRQ-4 assigned to [PCI Device] Legacy ISA for devices IRQ-7 assigned to [PCI Device] compliant with the IRQ-9 assigned to [PCI Device] original PC AT bus IRQ-10 assigned to [PCI Device] specification, PCI/ISA...
Page 54
ACPI Suspend Type [S1&S3] Select Menu Suspend Mode [Disabled] AC Power Loss Restart [Disabled] Item Specific Help Power Up Control Select the ACPI state Hardware Monitor used for System Suspend. : Help : Select Item : Change Value F5 : Setup Defaults ↑...
Page 55
Power Up Control Select Menu Item Specific Help Power Up On PCI Devices [Disabled] Power Up By PS/2 Keyboard [Disabled] Press [Enter] to select. Power Up By PS/2 Mouse [Disabled] Power Up by Onboard LAN [Disabled] RTC Alarm Resume [Disabled] Date (of Month) Resume Time (hh:mm:ss) 0 : 0 : 0...
Page 57
Hardware Monitor Select Menu ° Item Specific Help CPU Temperature ° MB Temperature Press [Enter] to enable CPU Fan Speed 5443RPM or disable. Chassis Fan Speed 0RPM VCore 1.79V + 3.3V 3.37V + 5V 4.94V + 12V 11.36V : Help : Select Item : Change Value F5 : Setup Defaults...
Page 58
Select Menu First Boot Device [HDD-0] Second Boot Device [CDROM] Item Specific Help Third Boot Device [Floppy] Fourth Boot Device [Disabled] Select your boot device Plug & Play OS [Yes] priority. Reset Configuration Data [Disabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Disabled]...
Page 60
Select Menu Save & Exit Item Specific Help Exit Without Saving Load SETUP Defaults This option saves data Discard Changes to CMOS and exits the Save Changes BIOS Setup. : Help : Select Item : Change Value F5 : Setup Defaults ↑...