Cisco 2821 - Integrated Services Router Unified Communications Bundle Configuration
Power up and initial configuration procedures
Hide thumbs
Also See for 2821 - Integrated Services Router Unified Communications Bundle:
- Quick start manual (47 pages) ,
- User manual (204 pages) ,
- Overview (27 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Power Up and Initial Configuration Procedures
for Cisco 2800 Series Routers
This document describes how to power up your Cisco 2800 series integrated services router and perform
an initial configuration to provide network access. It includes the following sections:
•
•
Powering Up Cisco 2800 Series Routers
Warning
Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)
that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not
operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement
1029
This section covers the following topics:
•
•
•
•
Checklist for Power Up
You are ready to power up the Cisco router if the following steps are completed:
•
•
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Configuring the Router, page 4
Checklist for Power Up, page 1
Power Up Procedure, page 2
Chassis is securely mounted and grounded.
Power and interface cables are connected.
Advertisement
Table of Contents
Related Manuals for Cisco 2821 - Integrated Services Router Unified Communications Bundle
Summary of Contents for Cisco 2821 - Integrated Services Router Unified Communications Bundle
-
Page 1: Table Of Contents
Power Up and Initial Configuration Procedures for Cisco 2800 Series Routers This document describes how to power up your Cisco 2800 series integrated services router and perform an initial configuration to provide network access. It includes the following sections: Powering Up Cisco 2800 Series Routers, page 1 •... -
Page 2: Power Up Procedure
Cisco 2800 Series Software Configuration Guide document. To view the boot sequence, you must have a console connection to the Cisco router before it powers up. Note Make sure that your PC is powered up and connected as described in the “Checklist for Power Up”... -
Page 3: Verifying The Front Panel Led Indications
LED Color or State Meaning Solid green System is operating normally Blinking green System is booting or is in ROM monitor mode Amber System error Power is off or power fault Power Up and Initial Configuration Procedures for Cisco 2800 Series Routers OL-5788-01... -
Page 4: Configuring The Router
(VICs, WICs, HWICs), and advanced integration modules (AIMs). Configuring the Router This section covers the following topics: Initial Configuration Using Cisco Router and Security Device Manager, page 5 • Initial Configuration Using the Setup Command Facility, page 5 •... -
Page 5: Initial Configuration Using Cisco Router And Security Device Manager
If you make a mistake while using the setup command facility, you can exit and run the setup facility Note again. Press Ctrl-c, and type setup at the privileged EXEC mode prompt ( Router# Power Up and Initial Configuration Procedures for Cisco 2800 Series Routers OL-5788-01... - Page 6 Configure SNMP Network Management? [yes]: Community string [public]: A summary of the available interfaces appears: The interface numbering that appears is dependent on the type of Cisco modular router platform Note and on the installed interface modules and cards. Current interface summary...
- Page 7 Press RETURN to get started! The user prompt appears. Router> Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 9 Step 11 verification procedures. Power Up and Initial Configuration Procedures for Cisco 2800 Series Routers OL-5788-01...
-
Page 8: Initial Configuration Using The Cisco Cli-Manual Configuration
Use the copy running-config startup-config command to save the configuration to NVRAM. When you have finished the initial configuration, verify the initial configuration. See the “Verifying the Step 6 Initial Configuration” section on page 9 for verification procedures. Power Up and Initial Configuration Procedures for Cisco 2800 Series Routers OL-5788-01... -
Page 9: Verifying The Initial Configuration
To verify that you configured the correct hostname and password, enter the show configuration • command. When you have completed and verified the initial configuration, your Cisco router is ready to configure for specific functions. See the “Completing the Configuration” section on page 9 for information about locating documentation for advanced configuration procedures. - Page 10 Configuring the Router CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...