Specifications - Behringer U-Control UMX250 User Manual

12
U-CONTROL UMX250 User Manual
3) Release the ASSIGN button.
4) Press the number keys on the keyboard to enter the controller number of
your choice (as described in Chapter 4.2.7).
5) Confirm your selection with ENTER. To discard your assignments either press
the CANCEL key or the ASSIGN button again. In either case the ASSIGN LED
goes out.
Remember to assign the OCTAVE SHIFT buttons to an individual MIDI channel if
you do not want to use the GLOBAL CHANNEL (see Chapter 4.2.2).
4.2.10 Velocity sensitivity
The sensitivity of the UMX250 can be regulated so that the velocity of the keys
has an effect on the volume level.
1) Press the ASSIGN button and keep it pressed.
2) Use the number keys to enter the keyboard velocity (see Table 4.1).
3) Release the ASSIGN button.
4) Confirm your selection with ENTER. To discard your assignments either press
the CANCEL key or the ASSIGN button again.
KEY
OFF: velocity value is fixed to 110. Change of key pressure has no
( 0 )
effect on volume level.
SOFT: key pressure is very sensitive; low velocity changes create
( 1 )
high changes in volume level.
MEDIUM: key pressure is "normal"; (very) hard hit notes are
( 2 )
(very) loud, (very) soft hit notes produce (very) low volume.
HARD: key pressure is more unsusceptible compared to all
( 3 )
other settings.
to
invalid input.
( 4 ) ( 9 )
Table 4.1: Effect of RANGE definition on keyboard velocity
4.2.11 The factory reset command
Please proceed as follows to reset all UMX250 settings to their factory defaults:
1) Press the ASSIGN button and keep it pressed.
2a) Press both OCTAVE SHIFT buttons for a temporary FACTORY RESET.
All currently modified control elements will be reset to their factory
defaults. However, the USERMEMORY remains as before and is not reset!
2b) Press keys ( 8 ) , ( 9 ) and ( 0 ) simultaneously for a complete FACTORY
RESET: Now not only the control elements of the FACTORY MEMORY but also
those of the USER MEMORY will be overwritten.
3) Release the ASSIGN button. The ASSIGN LED stays on.
4) Confirm your selection with ENTER. If you do not want to RESET the unit,
either press the CANCEL key or the ASSIGN button again.
EFFECT ON KEY VELOCITY

5. Specifications

USB Connections
Type
MIDI Connections
Type
Control Elements
Controller
Buttons
Keyboard
Switch Plug
Foot pedal
Power Supply
USB
Battery
Power connector
USA/Canada
China/Korea
UK/Australia
Europe
Japan
Power consumption
Dimensions/Weight
Dimensions (H x W x D)
Weight
BEHRINGER is constantly striving to manintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or liiustrated.
Type B; USB1.1
5-pin DIN plug OUT
1 control wheel with center reset
1 control wheel without center reset
8 rotary knobs
1 fader
12 buttons
25 keys; velocity-sensitive
¼" mono jack with automatic
polarity recognition
3 x 1.5 Volt Mignon (Type "AA")
2 mm DC jack, negative center 9 V,
100 mA regulated
120 V~, 60 Hz
220 V~, 50 Hz
230 V~, 50 Hz
230 V~, 50 Hz
100 V~, 50–60 Hz
max. 0.9 W
approx. 8 15/�� x 3 26/�� x 19 15/��"
approx. 215 x 97 x 495 mm
approx. 4 30/�� lbs / 2.24 kg